• 대한기계학회논문집B
• /
• 제32권8호
• /
• pp.621-628
• /
• 2008

A numerical study for the flow, heat and mass transfer characteristics of the evaporating tube with the films flowing down on both the inside and outside tube walls has been carried out. The condensation occurs along the outside wall while the evaporation occurs at the free surface of the inside film. The transport equations for momentum and energy are parabolized by the boundary-layer approximation and solved by using the marching technique. The calculation domain of 2 film flow regions (evaporating and condensation films at the inside and outside tube wall respectively) and tube wall is solved simultaneously. The coupling technique for the problem with the 3 different regions and the 2 interfaces of them has been developed to calculate the temperature field. The velocity and temperature fields and the amount of the condensed and evaporated mass as well as the position where the evaporating film is completely dried out are successfully predicted for various inside pressures and inside film inlet flow rates.

• 설비공학논문집
• /
• 제13권12호
• /
• pp.1236-1244
• /
• 2001

In the present study, the possibility of continuous slurry ice making using flowing water solution in a cooled tube has been investigated. The experiments were carried out at various concentration and velocity of water solution, temperature of cooled tube wall, and control pressure in a tube. As a result, four types of operating conditions, that is super-cooling, continuous ice making, intermittent ice making and ice blockage, were classified. And it was found that the critical condition for the continuous ice making was acquired as a function of these experimental parameters.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.415-420
• /
• 2003

Sedimentation phenomenon of suspended solids occurs by the gravitational force. Pollution particles are separated from slowly flowing wastewater in clarifier. Recently, the sludge suction collector is preferred rather than the scraper type sludge collector due to enhancement of the clarifier efficiency. The sludge suction collector is usually operated by the user's experiences without any scientific and/or technical consideration. To evaluate the performance of sludge suction collector, the three dimensional computer simulation was conducted by the finite volume method. To analyze the performance, the velocity vectors and the suction flow rates of the orifices were investigated. The result showed that each suction flow rate through out the collector was equivalent in the sludge suction collector and the efficiency of suction collector was good to remove high concentrated sludge in clarifier.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 A
• /
• pp.24-26
• /
• 1995

In this paper, we investigated transient fault currents in a magnetic coupling High-Tc superconducting current limiter(HCL). It has an important effect on the reliability and stability of the power system. In order to analyze transient fault characteristics of HCL, we fabricated a magnetic coupling HCL and tested it in different fault conditions. An important parameter of design and manufacture which makes HCL inherently reliable is reduction of inrush fault currents. Without inrush fault currents, the currents flowing under such conditions can be limited to a desired-value within one cycle. Inrush fault current depends on saturation, normal spot propagation velocity, turns ratio and the fault angle.

• Computers and Concrete
• /
• 제30권5호
• /
• pp.369-375
• /
• 2022

Current exertion reports the numerical analysis of boundary layer slip flow of Casson Nano fluid along a permeable cylinder that is stretching in exponential manner. The modeled PDEs are changed into nonlinear ODEs through appropriate nonlinear transformations. Numerical results are attained using a renowned numerical scheme shooting method with Runge-Kutta procedure of 6^th-order. Influential role of relevant parameters like Reynolds, suction, Casson fluid and slip parameters on velocity profile is investigated. The effect of influence of slip parameter γ on temperature profile is seen through graph. To ensure the authenticity of numerical procedure, outcomes of some special cases of present work are compared with published work and strong agreement is noticed.

• 한국산업융합학회 논문집
• /
• 제26권5호
• /
• pp.945-952
• /
• 2023

In this study, the sand casting process was applied to design the gating system and perform casting simulation in order to domestically produce the submarine mast cover. Based on simulation results, casting experiments were conducted to produce a soundness prototype. The design concept of the mast cover's gating system was based on the design of bell casting. By arranging eight tower-type gates in a circle at 45° intervals, the flow of melt flowing into each gate was uniform and did not mix with each other, and the velocity of melt was also uniform. The mast cover made of Ni-Al-Bronze alloy has no unfilled parts. However, small porosities and flow marks occurred on the surface in several places. Yield strength and ultimate tensile strength are 279.3 MPa and 675.7 MPa, respectively, and elongation is 21.2%.

• Tribology and Lubricants
• /
• 제2권2호
• /
• pp.12-19
• /
• 1986

냉각성, 난연성, 그리고 경제성의 면에서 우수한 윤활특성을 갖고 있는 이멀션윤활제를 사용하여 로울러와 프레이트간의 선접촉 및 광간섭계의 실험장치를 통하여 탄성유체윤활 영역에서의 윤활기구 및 분산립자의 거동기구를 명확히 하여 다음과 같은 결론을 얻었다. 1. 스퀴즈 유막내의 유동은 윤활간극이 비교적 넓은 경우와 좁은 경우로 대별하여 전자의 경우에는, 입자분포 및 속도분포의 영향이 크게 나타나며, 후자의 경우는 이멀션입자가 간극내에 정지하여 유막두께의 감소와 더불어 변형되어 간다. 2. 스퀴즈 유막내의 O/W, W/O 각 이멀션의 유동은 간극이 클 경우, 입경에 의한 속도차가 역으로 나타나고, 작은 경우에는 잔류액적의 분포가 서로 다르며 그밖에 O/W 형은 W/O 형에 비하여 분산입자가 쉽게 변형하는 것을 알 수 있다. 3. EHL영역입구부에서는 입자의 유동속도가 극히 적은 정체영역이 존재하며, 그 부근에서의 입자의 거동은 입경에 따라서 다르다. 4. 2색광에 의한 광간섭선의 관찰에 의하여 탄성유체윤활 영역내를 통과하는 이멀션유를 확인함과 동시에 EHL영역입구부에서의 분열거동이 관찰되었다.

• 한국항해항만학회지
• /
• 제30권1호
• /
• pp.113-117
• /
• 2006

이 실험의 목적은 튜브형 증발관에서 입구 공기 속도, 온도와 상대 습도에 따른 서리층 생성의 비교 검토에 있다. 입구 공기 속도와 온도는 각각 $0.3^m/_s,\;0.6^m/_s,\;0.9^m/_s,\;15^{\circ}C,\;20^{\circ}C,\;25^{\circ}C$로 하였고, 상대 습도는 $70\%\~90\%$로 하였다. 그리고 일반적인 공조기용 열교환기에서의 서리발생 현상을 파악하기 위하여 냉각튜브의 온도를 $-15^{\circ}C$로 일정하게 유지하였다. 그 결과 공급공기의 상대습도, 유속 및 온도가 증가할수록 서리 생성량이 증가함을 알 수 있었다.

• 한국해양학회지
• /
• 제14권2호
• /
• pp.71-77
• /
• 1979

낙동강은 유역이 약 2.4 $10^{4}$$\textrm{km}^2$ 이고 길이가 525km에 달하는 대하천으로 농업, 공업, 생활용수 등 영남지방의 용수 공급원으로서 중요하다. 최근에는 하구역 에서 천해어장, 홍수대책, 하도개수, 간척, 매립 등 다양한 이용개발이 계획 또는 실시 되고 있다. 따라서 이 하구역의 효육적 이용과 관리를 위하여는 하구수의 유동을 지배하는 요인인 하천조석에 관한 기초적인 연구가 불가결하다.

• Journal of Biosystems Engineering
• /
• 제33권6호
• /
• pp.384-389
• /
• 2008

Three prototype chestnut harvesters were constructed and evaluated their chestnut collection ability and field efficiency. Air-lock paddle system successfully picked up all loose material, and pick up efficiency was about 56 kg/h. Power required to operate this system was evaluated to be 8.7 kW with an air flow rate of $32.6\;m^3/min$. A radial blade type blower with 0.41 m impeller diameter was considered to be a minimum size for this system. For the auger system, air was sucked into the cylinder as the hinged flat cover began to be opened by the material pushed by the auger, and the empty burrs flew back to the container through the space between auger flights and collected in the bottom of the container. It was considered to add a device to prevent air from flowing back or to use the back flowing air for separation of burrs and nuts inside the container. The venturi system could not pick up chestnuts, as they only carried part way up to the suction hose. Consideration was given to an idea that the venturi could be used as a cleaning and separation mechanism for containers filled with both empty burrs and good nuts. A minimum vacuum of 129 mm wg was required to pick up chestnuts, and the corresponding inlet air velocity was 19.3 m/s. 104 mm of vacuum, which was about 81 % of that required for nuts, was enough to pick up burrs with nuts inside. Also, empty burrs with higher moisture content recorded the same pressure as for the burrs with nuts.