• Steel and Composite Structures
• /
• v.43 no.3
• /
• pp.389-401
• /
• 2022

This study investigated the flowability and mechanical properties of cost-effective steel fiber reinforced ultra-high performance concrete (UHPC) by using locally available materials for field-cast application. To examine the effect of mixture constituents, five mixtures with different fractions of silica fume, silica powder, ground granulated blast furnace slag (GGBS), silica sand, and crushed natural sand were proportionally prepared. Comprehensive experiments for different mixture designs were conducted to evaluate the fresh- and hardened-state properties of self-consolidating UHPC. The results showed that the proposed UHPC had similar mechanical properties compared with conventional UHPC while the flow retention over time was enhanced so that the field-cast application seemed appropriately cost-effective. The self-consolidating UHPC with high flowability and low viscosity takes less total mixing time than conventional UHPC up to 6.7 times. The X-ray computed tomographic imaging was performed to investigate the steel fiber distribution inside the UHPC by visualizing the spatial distribution of steel fibers well. Finally, the tensile stress-strain curve for the proposed UHPC was proposed for the implementation to the structural analysis and design.

• Korean Journal of Materials Research
• /
• v.30 no.10
• /
• pp.550-557
• /
• 2020

Used in the ceramic tile market as a representative building material, relief ceramic tile is showing increased demand recently. Since ceramic tiles are manufactured through a sintering process at over 1,000 ℃ after uniaxial compression molding by loading granule powders into a mold, it is very important to secure the flowability of granular powders in a mold having a relief pattern. In this study, kaolin, silica, and feldspar are used as starting materials to prepare granule powders by a spray dryer process; the surface of the granule powders is subject to hydrophobic treatment with various concentrations of stearic acid. The effect on the flowability of the granular powder according to the change of stearic acid concentration is confirmed by measuring the angle of repose, tap density, and compressibility, and the occurrence of cracks in the green body produced in the mold with the relief pattern is observed. Then, the green body is sintered by a fast firing process, and the water absorption, flexural strength, and durability are evaluated. The surface treatment of the granule powders with stearic acid improves the flowability of the granule powders, leading to a dense microstructure of the sintered body. Finally, the hydrophobic treatment of the granule powders makes it possible to manufacture relief ceramic tiles having a flexural strength of 292 N/cm, a water absorption of 0.91 %, and excellent mechanical durability.

• Journal of Powder Materials
• /
• v.29 no.5
• /
• pp.363-369
• /
• 2022

AlSi10Mg alloys are being actively studied through additive manufacturing for application in the automobile and aerospace industries because of their excellent mechanical properties. To obtain a consistently high quality product through additive manufacturing, studying the flowability and spreadability of the metal powder is necessary. AlSi10Mg powder easily forms an oxide film on the powder surface and has hydrophilic properties, making it vulnerable to moisture. Therefore, in this study, AlSi10Mg powder was hydrophobically modified through silane surface treatment to improve the flowability and spreadability by reducing the effects of moisture. The improved flowability according to the number of silane surface treatments was confirmed using a Carney flowmeter. In addition, to confirm the effects of improved spreadability, the powder prior to surface treatment and that subjected to surface treatment four times were measured and compared using s self-designed recoating tester. The results of this study confirmed the improved flowability and spreadability based on the modified metal powder from hydrophilic to hydrophobic for obtaining a high-quality additive manufacturing product.

• YAKHAK HOEJI
• /
• v.42 no.3
• /
• pp.284-289
• /
• 1998

The effect of reaction condition, solvent addition and thermal treatment on the bulk density, crystallinity and chemical properties of the freeze-dried cefazohn sodium was inves tigated to prepare the cefazolin sodium powder for injection with good flowability. Crystalline cefazolin sodium powder with high untapped-bulk density (about 45%) and low compressibility (about 40%) was obtained by solvent addition to the very highly concentrated cefazohn sodium solution followed by subsequent thermal treatment before freeze-drying. The desirable solvent was low substituted alcohol such as isopropyl alcohol and anhydrous ethanol with the final concentration of about 9%. The pH adjustment and nitrogen gas purging during the reaction did not give significant effect on the chemical properties such as content, color, transmittance and pH of the reconstituted cefazolin sodium aqueous solution.

• Computers and Concrete
• /
• v.20 no.3
• /
• pp.297-310
• /
• 2017

A CFD software was used to simulate free surface flow of SCC in the T-Box test. In total, seven simulations were developed to study the effect of rheological parameters on the non-restricted flow performance of SCC in both horizontal and vertical directions. Different suspending fluids having five plastic viscosity values between 10 and 50 Pa.s, three yield stress values between 14 and 75 Pa, one density of $2500kg/m^3$, and one shear elasticity modulus of 100 Pa were considered for suspension of 178 spherical particles of 20-mm diameter and $2500kg/m^3$ density. The results of the simulations are found to correlate well to changes in rheological parameters of the suspending fluid. Plastic viscosity was shown to be the most dominant parameter affecting flowability and dynamic stability compared to the yield stress. A new approach was proposed to evaluate performability of SCC based on a trade-off between flowability and dynamic stability.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.128-129
• /
• 2014

In this study, flowability of the mortar added with length change and combination of steel and inorganic fiber has been tested to evaluate the performance of fiber-reinforced mortar. The following results could be made as the conclusion. Early age flow of the mortar has been decreased when fibers added. Slump also decreased with the adding of fibers. For the air content, comparing with Plain, all the specimens with fibers showed higher air content than Plain., Addition of every kinds fibers showed the similar EIS test results.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.11a
• /
• pp.209-210
• /
• 2011

This study is aimed to draw a optimum combined fiber mix condition to improve spalling resistance and flowability of ultra high-strength concrete. As a result, W/B 12.5% concrete specimens were prevented spalling with PE0.05+ PP0.1, PE0.05+NY0.1 and W/B 12.5% concrete specimens were prevented spalling with all of combined organic fiber mix condition. But There is no significant influence of steel fiber under 5% volume ratios to prevent spalling. In the scope of this study, we suggest that condition of optimum volume ratio PE0.05+NY0.1 is to improve spalling resistance, flowability and residual compressive strength.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.10a
• /
• pp.1-7
• /
• 1995

In this paper, we decribed the basic elements required for the practical usage of super flowing concrete. The flowability and filingability of fresh concrete was measured by using six different testing methods. Also, two actual size members were used for investigating characteristics of the hardened concrete through variious experiments. As the result of the experimentation, the developed super flowing concrete shown high flowability and fillingability good enough for the requirement. Furthermore, inner uniformity of the no-vibrated concrete was verified by testing distribution of aggregates and core cylinders. Therefore, quality control and workability of concrete can be secured by using the super flowing concrete even without vibrating However, it ha been felt that development of easy evaluation methods for the super flowing concrete is in need.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.204-205
• /
• 2017

In this study, flowability and strength on ultra high performance concrete(UHPC) pre-mixed binders with fiber was investigated. The flow of UHPC with pre-mixed binders was higher than that of seperate mixing conditions. The UHPC using PVA fiber with high specific surface area showed a low flow compared to steel fiber. An pre-mixing method led to improved strength of UHPC and low deviation of specimens due to dispersion effect of each materials.

• Journal of Dairy Science and Biotechnology
• /
• v.40 no.3
• /
• pp.134-142
• /
• 2022

Protein-enriched dairy powder is widely consumed to promote muscle synthesis. Recently, in Korea, elderly people have also begun consuming protein powder products to prevent muscle loss. However, these protein-enriched powders have poor flowability and hydration properties because of the fine particles of spray-dried milk protein powder. Therefore, in this study, the fluidized bed agglomeration process was used to solve these problems. The rheological and physical properties of milk protein isolate (MPI)/skim milk powder (SMP) mixtures were effectively improved via fluidized bed agglomeration. The particle size of the MPI/SMP mixtures significantly increased from 35.7-58 ㎛ to 118-136 ㎛, the flowability level improved from fair (21.4-26.3) to good (15.7-16.3), and the cohesiveness level changed from intermediate (1.27-1.36) to low (1.18-1.19) after fluidized bed agglomeration. In addition, the wetting time of the agglomerated MPI/SMP mixtures was effectively reduced to 4.67-58.3 s by fluidized bed agglomeration. These findings may be useful for manufacturing protein-enriched dairy powders with good instant properties.