• The Korean Fashion and Textile Research Journal
• /
• v.17 no.3
• /
• pp.327-340
• /
• 2015

Male skirt is found in traditional costumes all over the world. Due to the development of tailoring skills in the early Middle ages, men started wearing breeches and pantaloons gradually distinguishing the different characteristics of menswear and womenswear. Since then, skirt became the strong representation of the female gender, symbolizing the feminism. However, under the influences of technological development and diversification in 2000s, gender identity has been diversely expressed in modern fashion allowing male gender to embrace different sexual identities. The purpose of the study is to analyze the nature of male skirts, which have been popularized in modern men's fashion through both the expressional elements and compositional elements. This study associates design elements of male skirt, gradually appearing in the contemporary men's fashion with the sexual symbolism and reinterpreted it's significance in the flow of the modern fashion. Reinterpretation of the gender image in costumes are considered to contribute to the cultural context and extension in diversity. These research results forms a basic foundation to expand in studies of men's fashion design and gender image of costumes through cultural contexts and it's changes. It is considered that this can lay groundwork to make various attempts at passing over the archetype of the gender image besides the continuous appearance of male skirt in the field of fashion design.

• The Journal of Engineering Geology
• /
• v.10 no.1
• /
• pp.13-25
• /
• 2000

A three-dimensional discrete fracture network model based on probabilistic characteristics of fracture geometry and transmissivity was designed to calculate the conductivity tensor and to estimate theanisotropy of conductivity. The conductivities, $K_p$, obtained from the numerical simulation of single-holepacker test corresponded well to those from the field tests. From this, it can be concluded that thefracture network model designed in this study can represent hydraulic characteristics of in-situ fractured rock mass. Block-scale conductivities, $K_b$, estimated from the modelling of steady-state flow through the REV-scale block were ranged between the arithmetic mean and harmonic mean of theconductivity estimates from packer tests. The conductivity along north-south direction was 1.4 timesgreater than that along the east-west direction. It was concluded that the anisotropy of conductivitywas insignificant. It was also found that there was a little correlation between $K_b$ and $K_p$. This would be to that the conductivities from the packer test simulation was strongly dependent on thetransmissivity and the number of fractures within the packer test intervals.

• Solar Energy
• /
• v.12 no.3
• /
• pp.47-59
• /
• 1992

In the concentric tube type recuperator, which is the most typical type of radiation recuperator, installed on the exhaust-secion of industrial furnace, air flows between the adiabatic outer tube and the inner tube in which exhausted gas flows with high temperature. The waste heat of the exhausted gas is transferred to the inner tube, and transferred from the inner tube to the flowing air. The heat transfer by radiation In the concentric tube type recuperator is modeled using spherical harmonics approximation, namely, P-N method and numerically analyzed considering the effect of dynamic flow field. The results are compared with the existing empirical data. In addition, a theoretical method is presented for the analysis of the heat transfer characteristics of a recuperator with a reradiator installed in the inner tube, which causes re-radiant in the inner tube, and the characteristics of the recuperator is analyszed and defined.

• Aerospace Engineering and Technology
• /
• v.9 no.1
• /
• pp.78-83
• /
• 2010

In the present paper, a flap was optimized to maximize the lift. A 2-element fowler flap system was utilized for optimization with an initial shape of general aviation airfoil and a flap shape designed by Wentz. Response surface method and Hicks-Henne shape function were implemented for optimization. 2-D Navier-Stokes method was used to solve flow field around aGA(W)-1 airfoil with a fowler flap. Commercial programs including Visual-Doc, Gambit/Tgridand Fluent were used. Upper surface shape and the flap gap were optimized and lift for landing condition was improved considerably. The original and optimized flaps were tested in the KARI's 1-m low speed wind tunnel to examine changes in aerodynamic characteristics. For optimized flap tests, the similar trend to prediction could be seen but stall angle of attack was lower than what was expected. Also, less gap than optimized design delayed stall and produced better lift characteristics. This is believed to be the effect of turbulence model.

• Journal of Navigation and Port Research
• /
• v.32 no.10
• /
• pp.771-776
• /
• 2008

The main purpose in having a control surface on a ship is to control the motion of it. It is the important element to determine the maneuvering characteristics of the ship. In this paper, the measured results has been compared with each other to predict the performance characteristics of flapped rudder's 2-dimensional section at $Re=3.0{\times}10^4$ using 2-frame grey level cross correlation PIV method. The side force of the rudder could be mainly improved by the lift force at 10 degrees angle of attack and the drag force at 20 degrees angle of attack. The separation point and boundary layer could be controlled by the change of the only flap's angle at 10 degrees angle of attack.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.2
• /
• pp.78-88
• /
• 2005

The combustion characteristics of End-Burning hybrid combustor using different types of injector system are numerically investigated to visualize the temperature fields in the combustion chamber The basic characteristics of combustion with different O/F ratio is also analyzed in order to capture the main behavior of diffusion flame inside the swirl induced hybrid combustion chamber It was found that the arrangement of oxidizer injectors give strong effect on the temperature field dominating mixing between fuel and oxidizer. The results show that among five different oxidizer injectors arrangement, the counter flow injector has the highest mixing efficiency. However, the observed high wall temperature presence near the oxidizer injectors remains to be solved.

• Applied Chemistry for Engineering
• /
• v.30 no.1
• /
• pp.95-101
• /
• 2019

The cremation rate of Korea in 2016 was 82.7% which is four times greater than 20.5% in 1994. As increasing the cremation rate gradually, it cause a shortage of cremation facilities resulting in building more cremation facilities to meet the increasing inquiries on cremation or a large amount of fuels for the longer operation of the crematory. In this study, the crematory system optimizing its thermal efficiency characteristics and also responding to increasing inquiries on cremation was proposed in order for solving such problems, In particular, the heat flow characteristics including a heat transfer coefficient by performing a simulation using computational fluid dynamics (CFD) was investigated. The CFD model was validated with on-site experiments for a cremation facility. As a result of the simulation, the fuel consumption decreased nearly 25% and residence time increased in the main combustor. Also, the improved crematory was constructed with an expanded combustor, heat exchanger, second combustion air system, refractory and insulation material. From on-site experiments, the energy consumption was saved to approximately 54.4%, while the burning time reduced nearly 20 minutes.

• Ecology and Resilient Infrastructure
• /
• v.7 no.4
• /
• pp.294-299
• /
• 2020

Based on the combined results of field surveys and analyses of the road structure and traffic flow, we propose a new plan for reducing roadside non-point pollution in the Paldang Water Source Protection Zone. The results show that the soil surrounding the roads in Paldang is highly permeable, which mitigates the need for filtration facilities. Roads flanked by steep slopes are found to facilitate the reduction of non-point roadside pollution through vegetation and soils along road slopes without the need for pollution reduction facilities. These results highlight the need for a flexible roadside non-point pollution reduction plan for roadside non-point pollution, which can be tailored to compliment relevant regulations and design standards after analyzing the characteristics of the target road.

• Journal of Korean Society on Water Environment
• /
• v.27 no.5
• /
• pp.699-709
• /
• 2011

The uses of multi-dimensional hydrodynamic and water quality models are increasing to support a sustainable management of large dam reservoirs in Korea. Any modeling study requires selection of a proper spatial dimension of the model based on the characteristics of spatial variability of concerned simulation variables. For example, a laterally averaged two-dimensional (2D) model, which has been widely used in many large dam reservoirs in Korea, assumes that the lateral variations of hydrodynamic and water quality variables are negligible. However, there has been limited studies to give a justification of the assumption. The objectives of this study were to present the characteristics of spatial variations of water quality variables through intensive field monitoring in Daechung Reservoir, and provide information on a proper spatial dimension for different water quality parameters. The monitoring results showed that the lateral variations of water temperature are marginal, but those of DO, pH, and conductivity could be significant depending on the hydrological conditions and local algal biomass. In particular, the phytoplankton (Chl-a) and nutrient concentrations showed a significant lateral variation at R2 (Daejeongri) during low flow periods in 2008 possibly because of slow lateral mixing of tributary inflow from So-oak Stream and wind driven patchiness.

• Journal of Ocean Engineering and Technology
• /
• v.36 no.5
• /
• pp.313-325
• /
• 2022

Recently around the world, coastal erosion is paying attention as a social issue. Various constructions using low-crested and submerged structures are being performed to deal with the problems. In addition, a prediction study was researched using machine learning techniques to determine the wave attenuation characteristics of low crested structure to develop prediction matrix for wave attenuation coefficient prediction matrix consisting of weights and biases for ease access of engineers. In this study, a deep neural network model was constructed to predict the wave height transmission rate of low crested structures using Tensor flow, an open source platform. The neural network model shows a reliable prediction performance and is expected to be applied to a wide range of practical application in the field of coastal engineering. As a result of predicting the wave height transmission coefficient of the low crested structure depends on various input variable combinations, the combination of 5 condition showed relatively high accuracy with a small number of input variables defined as 0.961. In terms of the time cost of the model, it is considered that the method using the combination 5 conditions can be a good alternative. As a result of predicting the wave transmission rate of the trained deep neural network model, MSE was 1.3×10^-3, I was 0.995, SI was 0.078, and I was 0.979, which have very good prediction accuracy. It is judged that the proposed model can be used as a design tool by engineers and scientists to predict the wave transmission coefficient behind the low crested structure.