• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.240-240
• /
• 2011

The first neutral beam injector (NBI-1) has been developed for the Korea Superconducting Tokamak Advanced Research (KSTAR) tokamak. A first long pulse ion source (LPIS-1) has been installed on the NBI-1 for an auxiliary heating and current drive of KSTAR core plasmas. Performance of ion and neutral beam extractions in the LPIS-1 was investigated initially on the KSTAR NBI-1 system, prior to the neutral beam injection into the main plasmas. The ion source consists of a JAEA magnetic bucket plasma generator with multi-pole cusp fields and a set of KAERI prototype-III tetrode accelerators with circular apertures. The inner volume of plasma generator and accelerator column in the LPIS-1 is approximately 123 liters. Final design requirements for the ion source were a 120 kV/ 65 A deuterium beam and a 300 s pulse length. The extraction of ion beams was initiated by the formation of arc plasmas in the LPIS-1, called as an arc-beam extraction method. A stable ion beam extraction of LPIS-1 has been achieved up to an 100 kV/42 A for a 4 s pulse length and an 80 kV/25 A for a 14 s pulse length. Optimum beam perveance of 1.21 microperv has been found at an accelerating voltage of 80 kV. Neutralization efficiency has been measured by using a water flow calorimetry (WFC) method of calorimeter and an operation of bending magnet. The full-energy species of ion beams have been detected by using the diagnostic method of optical multichannel analyzer (OMA). An arc efficiency of the LPIS was 0.6~1.1 A/kW depending on the operating conditions of arc discharge.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.478-478
• /
• 2012

Recently, there are many researches in order to increase the deposition rate (D/R) and improve film uniformity and quality in the deposition of microcrystalline silicon thin film. These two factors are the most important issues in the fabrication of the thin film solar cell, and for the purpose of that, several process conditions, including the large area electrode (more than 1.1 X 1.3 (m2)), higher pressure (1 ~ 10 (Torr)), and very high frequency regime (VHF, 40 ~ 100 (MHz)), have been needed. But, in the case of large-area capacitively coupled discharges (CCP) driven at frequencies higher than the usual RF (13.56 (MHz)) frequency, the standing wave and skin effects should be the critical problems for obtaining the good plasma uniformity, and the ion damage on the thin film layer due to the high voltage between the substrate and the bulk plasma might cause the defects which degrade the film quality. In this study, we will propose the new concept of the large-area multi-electrode (a new multi-electrode concept for the large-area plasma source), which consists of a series of electrodes and grounds arranged by turns. The experimental results with this new electrode showed the processing performances of high D/R (1 ~ 2 (nm/sec)), controllable crystallinity (~70% and controllable), and good uniformity (less than 10%) at the conditions of the relatively high frequency of 40 MHz in the large-area electrode of 280 X 540 mm2. And, we also observed the SEM images of the deposited thin film at the conditions of peeling, normal microcrystalline, and powder formation, and discussed the mechanisms of the crystal formation and voids generation in the film in order to try the enhancement of the film quality compared to the cases of normal VHF capacitive discharges. Also, we will discuss the relation between the processing parameters (including gap length between electrode and substrate, operating pressure) and the processing results (D/R and crystallinity) with the process condition map for ${\mu}c$-Si:H formation at a fixed input power and gas flow rate. Finally, we will discuss the potential of the multi-electrode of the 3.5G-class large-area plasma processing (650 X 550 (mm2) to the possibility of the expansion of the new electrode concept to 8G class large-area plasma processing and the additional issues in order to improve the process efficiency.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.148-148
• /
• 2011

Recently, there have been many research activities to develop the large-area plasma source, which is able to generate the high-density plasma with relatively good uniformity, for the plasma processing in the thin-film solar cell and display panel industries. The large-area CCP sources have been applied to the PECVD process as well as the etching. Especially, the PECVD processes for the depositions of various films such as a-Si:H, ${\mu}c$-Si:H, Si3N4, and SiO2 take a significant portion of processes. In order to achieve higher deposition rate (DR), good uniformity in large-area reactor, and good film quality (low defect density, high film strength, etc.), the application of VHF (>40 MHz) CCP is indispensible. However, the electromagnetic wave effect in the VHF CCP becomes an issue to resolve for the achievement of good uniformity of plasma and film. Here, we propose a new electrode as part of a method to resolve the standing wave effect in the large-area VHF CCP. The electrode is split up a series of strip-type electrodes and the strip-type electrodes and the ground ones are arranged by turns. The standing wave effect in the longitudinal direction of the strip-type electrode is reduced by using the multi-feeding method of VHF power and the uniformity in the transverse direction of the electrodes is achieved by controlling the gas flow and the gap length between the powered electrodes and the substrate. Also, we provide the process results for the growths of the a-Si:H and the ${\mu}c$-Si:H films. The high DR (2.4 nm/s for a-Si:H film and 1.5 nm/s for the ${\mu}c$-Si:H film), the controllable crystallinity (~70%) for the ${\mu}c$-Si:H film, and the relatively good uniformity (1% for a-Si:H film and 7% for the ${\mu}c$-Si:H film) can be obtained at the high frequency of 40 MHz in the large-area discharge (280 mm${\times}$540 mm). Finally, we will discuss the issues in expanding the multi-electrode to the 8G class large-area plasma processing (2.2 m${\times}$2.4 m) and in improving the process efficiency.

• 한국농공학회지
• /
• 제24권1호
• /
• pp.44-52
• /
• 1982

Recently, estuary reserovoirs have been actively constructed in Korea and also in Japan there are a large number of estuary reservoirs constructed. But most of the estuary reservoirs are located at the downstream of a river where geographical condition is best for the construction of an enclosing dam. And an effective utilization of water from the estuary reservoir seems to be difficult even if estuary reservoirs are considered to be the water resources the most available for their watershed. Studies on estuary reservoirs so far have been mainly concentrated on the physical and engineering problems of the dam construction itself. The purpose of the present study is to review the estuary reservoir planning in connection with the water resources development and to study a basis of the planning. First, the levels of water use in Korea and Japan were compared with those of other countries in the world. And then, some representative reservoirs were selected to study the roles of a reservoir and water-using conditions in the watershed. Based on the study, a survey was given on the relation between a dam construction upstream and an estuary reservoir construction downstream of a river. Finally, a comprehensive examination was made of the bases of estuary reservoir planning. (1) The estuary reservoir planning is deeply related to the plan for water use develo- pment in the watershed. After the upstream water resources were fully developed up to the most, water reso- urces development by an estuary reservoir should be started. (2) If an estuary lake has a capacity big enough, it can store flood discharge of the watershed without any loss and become a basic facility that will bring about the maxi- mum use of water from the watershed. (3) Estuary reservoirs store water used in the upstream watershed, so recycling of water use is attained by the reservoir. Water in the estuary lake is difficult to be fresh water in its long run. Therefore, estuary reservoir should be located at a place where polluted water is purified and refused. All the planning should be based on the assumption that water in the estuary lake is not fresh but polluted after a long time. (4) The estuary lake can only supply water to the lower basin directly. But the upstream area is benefited from the estuary lake by exchange of irrigation water sources between the lower and the upper area. So a large-scale exchange plan between new and existing water resources is important. By constructing estuary reservoirs and the exchange of water sources between upper and lower areas, the reasonable maximum use of water from the whole watershed is at- tained. (5) The big problem coming from the water resources development by an enclosing estuary is salt water intrusion into the lake. To maintain the estuary lake salt-free, multi-purpose use of the lake should be avoided. It is necessary to take such fundamental measures as abolition of back flow operation of gate, and the closing of the fish port and the fish ladder. The results mentioned above were found in this study and these results of this study could be used for the adequate planning of estuary reservoirs in connection with the maximum water use of the watershed.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 2005년도 학술발표논문집
• /
• pp.490-495
• /
• 2005

Organic compost has been widely applied to the cropland because it has been thought as Environmentally Sound Agriculture (ESA) in Korea. However, many field researches have been done to investigate water quality impacts of organic compost uses, compared to those from chemical fertilizer applications. It was found that pollutant loads from organic compost applied croplands were higher than those from chemical fertilizer applied areas. However, there might be other unknown factors affecting the results since the experiments were performed at the outside fields. In this study, indoor rainfall experiments using the Norton rainfall simulator systems were done to minimize and exclude errors from unknown sources by controlling soil characteristics, rainfall amount, rainfall intensity, and fertilizer treatments. The amounts of surface runoff and groundwater percolated from 10% and 20% slope plots were measured and water quality samples were collected and analyzed for BOD, COD, and T-P. Flow weighted mean concentration (FWMC) values were computed to assess effects of different fertilizer treatments. It was found that average concentration values of BOD were 5.57 mg/L from chemical fertilizer treated plot and 8.08 mg/L from organic compost treated plots. For 10% slope, FWMC BOD values from organic compost treated plots were higher by 29.9% than those from chemical fertilizer treated plots. For 20% slope, FWMC BOD values from organic plots were higher by 38.8% than those from chemical fertilizer plots. FWMC BOD values for 20% slope plots were higher than those from those for 10% slope plots. The similar trends were found for COD and T-P. In Korea, excessive use of organic compost has caused extremely high levels of organic matter contents at the cropland. Organic compost are usually applied to the cropland to improve soil quality, while chemical fertilizer is applied to help crop growth. Since organic compost is very slow in releasing its nutrients to the soil, farmers usually apply excessive organic compost for immediate effects and maximum crop yields, which has been causing soil and water quality degradations. Therefore, thorough investigations for better nutrient management plans are needed to develop the ESA strategy in Korea.

• 에너지공학
• /
• 제28권4호
• /
• pp.35-41
• /
• 2019

기존에 차량용 안개등으로 사용되었던 할로겐 광원은 전력소모가 증가하고 수명이 짧기 때문에 이러한 단점을 극복하기 위해 자동차 광원은 LED로 점차 바뀌고 있다. 그러나 차량용 LED 안개등을 점등하였을 경우에는 LED에서 발생하는 고열로 인해 안개등 수명을 단축시키는 단점이 있다. 안개등 내부에서 LED에 의해 발생된 열은 주로 히트싱크에 의해 배출되지만, 나머지 열은 거의 대부분 대류를 통해 외부로 배출된다. 이러한 대류에 의한 냉각효율이 저하되면 열에너지는 램프의 주요부품인 렌즈, 리플렉터, 베젤 등에 열을 발생시키거나 LED 광원에 고온을 발생시켜 LED 안개등의 수명을 단축시킨다. 따라서, 본 연구에서는 히트싱크에 의한 방열방식 이외에도 냉각효율에 중요한 영향이 미치는 대류에 의한 방열성능을 개선하고자 하였다. 이를 위해 차량용 LED 안개등 내부공기를 외부로 흡·배출시킬수 있는 통풍구 설치 위치를 결정하기 위한 열유동해석을 수행하여 최적의 설계가 되도록 하였다. 공기의 평균속도는 기존 프로토타입인 Case1에 비해 Case3, Case2의 순으로 증가되었고 Case3의 증가폭이 다른 Case에 비해 상대적으로 큰 것을 알 수 있었다. 이는 안개등 상·하에 설치된 통풍구가 온도차이에 따라 생성되는 대류현상을 적절하게 유도하기 때문에 공기의 속도 증가와 함께 열을 효율적으로 배출시켰기 때문인 것으로 판단하였다.

• 생태와환경
• /
• 제37권2호통권107호
• /
• pp.205-212
• /
• 2004

아시아 몬순지역에서 대형댐의 인순환(phosphorus cycle)과정의 특징을 파악하기 위하여 소양호를 대상으로 인순환 과정을 조사하였다. 또한, 이를 모의하기 위해 2차원 수질모델인 CE-QUAL-W2를 적용하여 수중생태계의 물질순환과정을 모의하였다. 소양호는 수심이 깊고성층이 강하여 수직적인 변이가 뚜렷한 인의 분포를 보였다. 인의 부하량은 유역면적의 90%를 차지하는 주유입하천인 소양강의 인농도를 측정하여 산정하였다. 소양강의 인농도는 강우시 유량 증가에 따라 크게 증가하는 변동을 보였으므로 인의 부하량은 간헐적으로 발생하는 폭우 유출에 집중되었다. 폭우시 유출수는 수온이 낮아지기 때문에 호수의 중층으로 잠류하여 중층 탁수대를 형성하는 것으로 관측되었다. 여름 우기가 끝난 후 중층에는 두께 20${\sim}$30m의 인함량이 높은 탁수층이 형성되었으며 이탁수층은 댐 중간수심에 만들어진 발전방류구를 통하여 서서히 방류되었다. CE-QUAL-W2 모델은 호우시 탁수의 잠류현상과 인함량이 높은 중층의 형성, 인의 수평수직분포 등의 인순환 과정이 잘 모의 하여,아시아 몬순지역의 댐에서 수질모델로서 육수학적 현상을 잘 모의하는 것으로 평가된다.

• 한국세라믹학회지
• /
• 제40권10호
• /
• pp.967-972
• /
• 2003

직경 5 cm cold hollow cathode 이온원을 박막의 이온보조증착법 또는 이온보조반응법에 사용하기에 적합한 이온빔으로 넓은 면적을 균일하게 조사할 수 있는 이온원을 설계, 제작하기 위한 방안으로 연구하게 되었다. 이온원은 글로우 방전을 위한 음극과 이온화 효율의 증가를 위한 자석, 플라즈마 챔버, 그리드 전극으로 이루어진 이온광학시스템, 직류전원공급장치로 이루어진다. 전자인출전극의 구조 및 형태로 구분하여 한개의 노즐로 이루어진 (I) 형태와 복수개의 노즐로 변형된 (II) 형태로 제작하였다. 서로 다른 구조의 전자인출전극 (I)형태와 (II) 형태를 부착한 이온원에 beam profile을 측정한 결과 (I) 형태의 전자인출전극을 부착한 경우에는 이온원의 중심에서 140 $\mu\textrm{A}$/$\textrm{cm}^2$으로 측정되어 졌으며, 외곽으로 멀어질수록 급격히 전류밀도가 감소하여 균일한 영역(최대값의 90%)은 직경 5 cm로 측정되어졌다. (II) 형태로 변형되어진 이온원의 경우 중심에서 65 $\mu\textrm{A}$/$\textrm{cm}^2$으로 (I) 형태와 비교하여 상대적으로 낮은 전류밀도가 측정되었지만 외각으로 멀어졌을 경우에도 전류밀도는 완만하게 감소하여 균일한 영역은 직경 20 cm로 측정되었으며, 본 연구목적에 부합되는 특성이 측정되었다. 이온빔 균일도가 증가한 (II) 형태의 전자인출전극을 부착한 이온원으로 주입하는 아르곤 가스량의 변화, 이온광학시스템의 플라즈마 그리드 전극과 가속 그리드 전극 간격의 조절, 이온빔 에너지 변화에 따른 beam profile 및 특성을 괸찰하였다.

• 한국농림기상학회지
• /
• 제1권1호
• /
• pp.29-35
• /
• 1999

본 연구는 경기도 광주지역의 낙엽송 임분에 인공 강우기를 설치하여 수리특성과 관련한 공간 변이와 상관관계를 구명하기 위하여 수행되었다. 수분유속과 보유능은 원래 토성, 구조와 유기물을 근거로 지표면에서 인공가우기로 수분을 일정속도로 가하면서 측정하였다. 이 방법은 간단히 유기물을 제거하거나 기존의 상태에서 수평한 지표면에 3가지의 강우 강도에서 실시하였으며 한편 경계면은 안정하며 포화상태의 습윤 토양에서 투수계수와 매트릭 유속기능을 조사하였다. 투수계수는 $_1$( $Z_{c}$) = $_2$( $Z_{c}$) = $_{c}$ 이라는 지속적 유속 조건하에서 $K_{i+}$$_1$ $_{c}$= $K_{i}$( $_{c}$) [1-d /dz]의 공식을 적용하였다. 본 연구 결과 토양내에서 유속에 영향을 미치는 공극 특성과 유기물 함량이 광범위하게 수분 보유능과 포화투수계수의 공간 변이에 영향을 미치는 것으로 조사되었다.것으로 조사되었다.되었다.

• Journal of Acupuncture Research
• /
• 제21권6호
• /
• pp.281-289
• /
• 2004

Objective : Blepharoptosis is drooping of eyelid which causes impairment of visual field by covering partially or completely, and it is classified into congenital ptosis and acquired one. In western medicine, idiopathic blepharoptosis is usually treated by tarsectomy. Contrary to that concept, we consider eyelid is assigned to Yookryoon(肉輪) among Ohryoon(五輪) which matches to spleen. In oriental medicine, it can be treated by promoting spleen and kidney. Here I report two cases of idiopathic blepharoptosis improved by conservative acupuncture therapy and herb medicine. Methods : The changes in clinical symptoms of general body weakness, anorexia, dizziness, dry eye, etc, in degree of eyelid drooping and in individual expression were described as they were treated with acupuncture therapy, herb medicine, Bojoong-ikgi-tang(補中益氣湯) and some physical therapy including Negative, I.C.T, S.S.P and Carbon. Results : Symptoms(ex) general body weakness, anorexia, dizziness, dry eye, etc) at admission improved and disappeared gradually with acupuncture therapy and herb medicine. The patients could discharge with favorable recovery. Conclusions : In oriental medicine, blepharoptosis is mainly treated by promoting Qihyul(氣血) and enhancing flow of that. If the patient has deficiency of Suhnchun-poomboo(先天稟褓賦) and Mungmoon-hwa(命門火), he is treated by promoting Shin-yang(腎陽). If he is weak in Bee-qi(脾氣), he needs to be treated by strengthening Bee-yang(脾陽) where patient with lack of Ganhyul(肝血) is supposed to be treated by promoting Hyul(血). These following two cases were managed by acupuncture, herb medicine and physical therapy on idiopathic blepharoptosis.