• 한국항해항만학회지
• /
• 제37권6호
• /
• pp.673-680
• /
• 2013

본 연구는 요트체험 활동 참여자들의 몰입도가 만족도 및 자아존중감에 미치는 영향에 관한 것으로서 우리나라 요트문화 및 레저산업의 대중화 실현에 기초자료를 제공하는데 그 목적이 있다. 이러한 연구 목적을 달성하기 위해 부산 울산 경남지역 주민을 대상으로 해양레저 아카데미 및 해양레저 체험 프로그램에 참여한 경험이 있는 대상자 총 428명을 모집단으로 선정하여 설문조사를 실시하였으며, 자료처리 방법은 빈도분석, 신뢰도분석, 타당도분석, 단순회귀분석, 다중회귀분석을 사용하였다. 이상과 같은 연구방법 및 자료분석의 결과를 통해 도출된 결론은 다음과 같다. 첫째, 요트체험 참가자들의 몰입도는 만족도에 정적인 영향을 미치는 것으로 나타났다. 둘째, 요트체험 참가자의 몰입도는 자아존중감(일반요인, 가정요인, 직장요인, 사회요인)에 정적인 영향을 미치는 것으로 나타났다. 셋째, 요트체험 참가자의 만족도는 자아존중감(일반요인, 가정요인, 직장요인, 사회요인)에 정적인 영향을 미치는 것으로 나타났다.

• 한국도로학회논문집
• /
• 제15권5호
• /
• pp.217-226
• /
• 2013

PURPOSES : Under the capacity conditions with balanced approach flows, roundabouts give less delay than existing signalized intersections; however, flows over 450 vehicles/hour/lane with unbalanced approach flow conditions, roundabouts efficiency drops due to the short time difference between the critical gap and the follow-up headway. The purpose of this study is developing a roundabout Signal Metering operation method by considering approach lanes degree of saturation. METHODS : A four-way-approach with one-lane roundabout is selected to compare the Signal Metering performance for the case of 16 different unbalanced flow conditions. Based on these traffic conditions, the performance is evaluated for 64 different cases of Signal Metering combinations by using SIDRA software. A degree of saturation(V/C ratio) sum for two adjoined approaches is used for the performance index of choosing Metered Approach and Controlling Approach. RESULTS : When the V/C ratio sum is 0.29~0.81 and Metered Approach flow is less than Controlling Approach flow, the average delay saving per vehicle is about 7 seconds; however, after this rage the delay saving decreases gradually until the V/C ratio sum reaches around 1.0. The range of V/C ratio sum 0.93~1.09 provides average delay saving per vehicle about 3 seconds. In case of V/C ratio sum is grater than 1.0 and the flows of Metered Approach is grater than Controlling Approach, the average delay per vehicle increases 3~11 times respectively. CONCLUSIONS : As expected, the Signal Metering provides substantial improvements in delay saving for the case of V/C ratio sum is 0.3~1.0 under the traffic flow conditions of Metered Approach is less than Controlling Approach.

• 디지털융복합연구
• /
• 제20권2호
• /
• pp.389-398
• /
• 2022

최근 관광 및 레저 관련 VR(가상현실) 콘텐츠가 관심을 받고 있다. 따라서 본 연구는 360° VR 관광 콘텐츠의 이용동기, 플로우, 지속사용의도가 콘텐츠 이용자들의 방문의도에 영향을 미치는지를 중국인 유학생을 대상으로 설문 분석하였다. 연구결과, 360° VR 관광 콘텐츠의 이용동기 중에서 쾌락적 혜택과 개인적 혜택은 콘텐츠 이용자들의 방문의도에 유의한 영향을 주는 것으로 나타났다. 그러나 생생함과 편리성은 방문의도에 영향을 미치지 않았다. 또한, 플로우는 방문의도에 긍정적인 영향을 미치는 것으로 나타났으나 지속사용의도는 방문의도에 영향을 주지 않았다. 이는 360° VR 관광 콘텐츠의 이용동기, 플로우, 지속사용의도가 방문의도에 영향을 주는지에 대해 규명한 것에 의의가 있고 360° VR 관광 콘텐츠 소비가 방문의도를 강화시키는 마케팅 도구가 될 수 있다는 것을 시사한다.

• 센서학회지
• /
• 제30권3호
• /
• pp.125-130
• /
• 2021

In this study, the degree of alignment of polymer microfibers produced by electrospinning using a rotating water collector was evaluated. Aligned micro- and nano-fibers are required in various practical applications involving anisotropic properties. The degree of fiber alignment has many significant effects; hence, and accurate quantitative analysis of fiber alignment is necessary. Therefore, this study developed a simple and efficient method based on two-dimensional fast Fourier transform, followed by ellipse fitting. As a demonstrative example, the polymer microfibers were electrospun on the rotating water collector as the alignment of microfibers can be easily controlled. The analysis shows that the flow velocity of the liquid collector significantly affects the electrospun microfiber alignment, that is, the higher the flow velocity of the liquid collector, the greater is the degree of microfiber alignment. This method can be used for analyzing the fiber alignment in various fields such as smart sensors, fibers, composites, and textile engineering.

• Restorative Dentistry and Endodontics
• /
• 제27권1호
• /
• pp.77-86
• /
• 2002

Current composites are made with dimethacrylate monomers and silane-treated silica microfillers, either alone or with silane treated glass fillers The main reasons for clinical failure of dental composites are secondary caries, wear and fracture. Most of practitioner want to get a composite which is more tougher under occlusal stress, less polymerization contraction, and better handling properties in application clinically. The aim of this study was to investigate the influence of resin matrix with various flows on the physical proper-ties such as fracture toughness and degree of conversion of the experimental resins. It was hypothesized that flexible or tough resin composites can be designed by judicious choice of monomer composition Various flow resin matrices containing Bis-GMA, UDMA, and TEG-DMA were made by altering the pro-portion of the monomers. After the unfilled resins were light-cured for different light intensity, the fracture toughness(K$_{1c}$) was measured according to ASTM standard using the single edge notched geometry, and degree of conversion(DC) was measured by FTIR. And experimental composites were formulated with variations in the proportion of silanated quartz and strontium glass fillers as 60, 75, and 77wt%. Also, the physical properties of composites with various filer contents were evaluated as same manner. All resulting data were compared by ANOVA/Tukeys test at 0.05 level. The results were as follows; 1. The degree of conversion of high flow resin containing less Bis-GMA was higher than that of low flow unfilled resin 2. While the degree of conversion of unfilled resin was increased according to light intensity for polymerization, there was no significant increase with moderate and high light intensity. Also, the fracture toughness was not increased by high light intensity. 3. The fracture toughness was high in the low flow unfilled resin containing higher contents of Bis-GMA. 4. There was a significant increase for fracture toughness and a tendency for degree of conversion to be reduced when the content of fillers was increased. 5. In the experimental composites, the flow of resin matrix did not affected on the fracture toughness, even, which was decreased as increase of viscosity. These results showed that the physical properties of a dental composite could be attributed to the flow of resin matrix with relative content of monomers. Specific combination of resin monomers should be designed to fulfil the needs of specific indication for use.

• 동력기계공학회지
• /
• 제21권3호
• /
• pp.45-50
• /
• 2017

This paper presents the Coefficient of performance(COP) and mass flow ratio of cascade refrigeration system with respect to refrigerants appling to high temperature cycle. The operating parameters considered in this study include degree of superheating and subcooling, compressor efficiency, evaporating temperature, condensing temperature and internal heat exchanger effectiveness in high temperature cycle. The result of this study is as follows : The COP of cascade system increases with increasing degree of superheating and subcooling, compressor efficiency and internal heat exchanger effectiveness except increasing condensing temperature. The mass flow ratio of low and high temperature cycle increases with increasing evaporating temperature and condensing temperature, but decreases with increasing internal heat exchanger effectiveness, degree of superheating and subcooling. Also, the mass flow ratio has no correlation with compressor efficiency at high temperature cycle.

• 대한기계학회논문집
• /
• 제12권3호
• /
• pp.582-589
• /
• 1988

본 연구에서는 작동유체로서 습공기를 사용하였을때 수반되는 응축에 의한 전 압손실을 실험과 수치해석을 통하여 정체점에 있어서의 습공기의 온도, 과포화도 및 노즐 팽창율의 효과와 액적 질량비 (g)과의 관계로서 구명하였다.

• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.75-81
• /
• 2003

In this paper, the study of effects of flow variables on flame structure and NOx emission concentration was performed in co-axial laminar partially premixed methane/air flames. the objectives are to reveal its effect as parameters were varied and to understand the correlation between flame structure and NOx emission characteristics in the reaction zone. equivalence ratio(${\Phi}$), fuel split degree(${\sigma}$), and mixing distance(x/D) were defined as a premixing degree and varied within $1.36{\sim}3.17$(equivalence ratio), $50{\sim}100$(fuel split degree), and $5{\sim}20$(mixing distance). the image of $OH{\ast}$ and $CH{\ast}$, and NOx concentration were obtained with an ICCD camera and a NOx analyzer. additionally the maximum intensity location of $OH{\ast}$ chemiluminescence and $CH{\ast}$ chemiluminescence were measured to compare each flame structures. In conclusion flame structure and NOx emission characteristics were changed from diffused to premixed flame when mixing degree was on the increase. the main effect on flame structure and NOx production was at first equivalence ratio(${\Phi}$), and next fuel split degree(${\sigma}$), and finally mixing distance(x/D).

• 한국산림과학회지
• /
• 제104권2호
• /
• pp.213-220
• /
• 2015

본 연구는 부산 및 울산광역시의 토석류 유출 위험지역 총 15개소에서 토석류 유출에 영향을 미치는 산림 환경인자에 대한 인자별 발생분포비율을 분석하였다. 토심은 중(30~99 cm), 방위는 동사면과 북동사면 및 북서사면, 표고는 100~200 m, 산지평균경사는 $20^{\circ}$ 미만, 모암은 화성암, 과거 토석류 유출이 있었던 지역, 최대시우량은 50~100 mm, 1일 최대강우량은 300 m 이상, 수계밀도는 $3{\sim}4km/km^2$, 산사태 발생 가능성이 있는 경사 $20^{\circ}$ 이상의 분포비율은 20~40%와 40~60%, 산사태 위험도 2등급 이상 비율은 40~60%, 유목이 있는 상태, 사방공작물 시설이 없는 지역, 4영급, 임분이 밀한 지역, 혼효림 등의 인자가 토석류 발생에 기여하는 것으로 분석되었다.

• 문화기술의 융합
• /
• 제6권4호
• /
• pp.165-170
• /
• 2020

본 연구에서는 정맥수액주입 교육을 위해 VR 360도 영상콘텐츠를 졸업학년의 간호대학생에게 적용한 후 감정이입과 몰입을 파악함으로서 향후 VR 360도 교육용 콘텐츠 활용에 대한 기초자료를 제시하고자 시도되었다. VR 360도 정맥수액주입 교육용 콘텐츠는 기획, 제작, 수정 및 완료의 4단계 과정으로 개발되었다. 본 연구의 설계는 서술적 조사연구로 연구기간은 2019년 11월 9일에서부터 11월 22일까지였다. 연구대상은 일개 대학의 4학년 간호대학생으로 총 64명이었다. 간호대학생은 연구자의 안전관리 하에 HMD(head mounted display)를 이횽한 VR 360도 정맥주입 교육용 콘텐츠를 감상하였다. 연구결과 간호대학생의 감정이입은 7점 만점 기준에 5.32±0.88점이었고, 몰입은 6.02±0.84점이었다. 본 연구에서 개발된 VR 360도 정맥수액주입 교육용 콘텐츠는 교과 및 비교과에서 교육매체로 사용할 수 있을 것이며, 향후 연구에서 교수학습방법을 구체적으로 개발하고 검증할 필요가 있다.