• Journal of Astronomy and Space Sciences
• /
• 제27권4호
• /
• pp.377-382
• /
• 2010

In lunar explorer development program, computer simulator is necessary to provide virtual environments that vehicle confronts in lunar transfer, orbit, and landing missions, and to analyze dynamic behavior of the spacecraft under these environments. Objective of simulation differs depending on its application in spacecraft development cycle. Scope of use cases considered in this paper includes simulation of software based, processor and/or hardware in the loop, and support of ground-based flight test of developed vehicle. These use cases represent early phase in development cycle but reusability of modeling results in the next design phase is considered in defining requirements. A simulator architecture in which simulator platform is located in the middle and modules for modeling, analyzing, and three dimensional visualizing are connected to that platform is suggested. Baseline concepts and requirements for simulator development are described. Result of trade study for selecting simulation platform and approaches of defining other simulator components are summarized. Finally, characters of lunar elevation map data which is necessary for lunar terrain generation is described.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제27회 추계학술대회논문집
• /
• pp.106-109
• /
• 2006

The purpose of this study is to analyze the installed performance of the PW206C turbo shaft engine used in the development of the smart UAV(Unmanned Ariel Vehicle) by KARI(Korean Aerospace Research Institute). It mainly aims to investigate performance behavior at installed conditions using both inlet and exhaust losses generated by CFD analysis of the ducts. The ways employed to be able to analyze the performance extensively were mainly rallied out by performing design point analysis of the engine where the performance simulation results from the commercial program 'GASTURB 9' used for simulation were used as inlet boundary condition for the ducts in CFD program The use of CFD tool involve modeling of the ducts to conform with the stipulated shape and sizes as defined by KARI with a grid density that allows reasonable flow characteristics applicable to aircraft components. Respective values of Shaft horse power obtained by varying flight Mach number, Gas generator RPM and Altitude considering several losses inclusive of those estimated by use of CFD tool were then plotted at three conditions with the ECS-OFF, ECS-MAX and at un-installed condition. Reasonable results were obtained as a result of using computational fluid dynamics that can hence be justified as an alternative tool for use in future flow analysis of engine and components.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.799-802
• /
• 2002

Korea Aerospace Research Institute has been developing a 50-meter class airship to demonstrate the technology to be used in the development of a stratospheric airship, and importance of accurate prediction of the dynamic behavior of an airship before flight test is widely conceived. The added mass has large impact on the dynamic characteristics of an airship unlike for an airplane and the added mass of the airship with empennage is predicted in this paper. At first, the usability of the strip theory is examined which integrates the analytic two dimensional results in the cross section along the longitudinal axis. A panel method with the surface distribution of sources is developed and its validity is also examined. Finally, the panel method with both source and doublet distributions is implemented, and it is validated and applied for the calculation of the added mass of a 50-meter class airship. Using the methods developed, the influence of empennage and control surface deflection on the added mass property of the airship is studied.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.575-580
• /
• 2004

In this work, the effect of composite couplings and mass distributions on hub loads of a hingeless rotor in forward flight is investigated. 1'he hingeless composite rotor is idealized as a laminated thin-walled box-beam. The nonclassical effects such as transverse shear and torsion warping are considered in the structural formulation. The nonlinear differential equations of motion are obtained by applying Hamilton's principle. The blade responses and hub loads are calculated using a finite element formulation both in space and time. The aerodynamic forces acting on the blade are calculated using the quasi-steady strip theory. The theory includes the effects of reversed flow and compressibility The magnitude of elastic couplings obtained by MSC/NASTRAN is compared with the classical pitch-flap($\delta$$_{3}$) coupling. It is observed that the elastic couplings and mass distributions of the blade have a substantial effect on the behavior of $N_{b/}$rev hub loads. About 40% hub loads is reduced by tailoring or redistributing the structural properties of the blade.f the blade.

• 한국소음진동공학회논문집
• /
• 제14권8호
• /
• pp.734-740
• /
• 2004

In this work, the effect of composite couplings and mass distributions on hub loads of a hingeless rotor in forward flight is investigated. The hingeless composite rotor is idealized as a laminated thin-walled box-beam. The nonclassical effects such as transverse shear and torsion warping are considered In the structural formulation. The nonlinear differential equations of motion are obtained by applying Hamilton’s principle. The blade responses and hub loads are calculated using a finite element formulation both in space and time. The aerodynamic forces acting on the blade are calculated using the quasi-steady strip theory. The theory includes the effects of reversed flow and compressibility. The magnitude of elastic couplings obtained by MSC/NASTRAN is compared with the classical pitch-flap($\delta$$_3$) coupling. It Is observed that the elastic couplings and mass distributions of the blade have a substantial effect on the behavior of $N_{b}$ /rev hub loads. About 40％ hub loads is reduced by tailoring or redistributing the structural properties of the blade.e.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권4호
• /
• pp.342-348
• /
• 1997

In this paper, the behavior of electron swarm parameters and energy distribution function of the discharge under high E/N condition in e$^{-10}$ -CF$_{4}$ gas have been analysed over the E/N range from 1-300(Td) by the MCS and BEq methods using set of electron collision cross section determined by the authors. The swarm parameters and energy distribution function have been calculated for the pulsed Townsend, steady-state Townsend and Time of Flight methods. The results gained that the value of electron swarm parameters such as the electron drift velocity, the electron ionization and attachment coefficients and longitudinal diffusion coefficients in agreement with the experimental and theoretical data for a range of E/N. The electron energy distribution function has been explained and analysed in e$^{-10}$ -CF$_{4}$ at E/N : 5, 10, 100, 200, 300(Td) for a case of the equilibrium region in the mean electron energy and respective set of electron collision cross sections. The validity of the results has been confirmed by TOF and SST methods.

• 영어어문교육
• /
• 제7권2호
• /
• pp.167-185
• /
• 2002

The purpose of this article is to examine the relationship between sin and grace represented in The Power and the Glory. This work is composed of two thriller patterns of the pursuer and the pursed. The first pursuit is that the whisky priest, the representative of religious order is pursued by the lieutenant, the representative of secular order. And the second pursuit is that the whisky priest is trying to escape from God. In the course of his flight from God the whisky priest discovers his sinful nature and this self-recognition helps him restore his proper relationship with God. When he was a young priest he had religious piety, but he didn't feel true love for others. Ironically, after he is corrupted he finds his sinful nature and regrets his wrong behavior. He then comes to understand God's will and his responsibility to have love for the miserable human beings. The whisky priest is willing to accept his destiny as a martyr, after having repented his sins to God. Though the lieutenant captures the whisky priest and executes him, he doesn't feel triumph or hope but feels empty. The Power and the Glory shows us the irony that the lieutenant's power is a symbol of his weakness, while the priest's weakness is a symbol of his power.

• Advanced Composite Materials
• /
• 제17권4호
• /
• pp.373-407
• /
• 2008

This paper will examine the possibilities of the virtual tests of composite structures by simulating mechanical behaviors by using supercomputing technologies, which have now become easily available and powerful but relatively inexpensive. We will describe mainly the applications of large-scale finite element analysis using the direct numerical simulation (DNS), which describes composite material properties considering individual constituent properties. DNS approach is based on the full microscopic concepts, which can provide detailed information about the local interaction between the constituents and micro-failure mechanisms by separate modeling of each constituent. Various composite materials such as metal matrix composites (MMCs), active fiber composites (AFCs), boron/epoxy cross-ply laminates and 3-D orthogonal woven composites are selected as verification examples of DNS. The effective elastic moduli and impact structural characteristics of the composites are determined using the DNS models. These DNS models can also give the global and local information about deformations and influences of high local in-plane and interlaminar stresses induced by transverse impact loading at a microscopic level inside the materials. Furthermore, the multi-scale models based on DNS concepts considering microscopic and macroscopic structures simultaneously are also developed and a numerical low-velocity impact simulation is performed using these multi-scale DNS models. Through these various applications of DNS models, it can be shown that the DNS approach can provide insights of various structural behaviors of composite structures.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.741-747
• /
• 2010

발사체의 추진공급시스템에 사용되는 벤트/릴리프밸브는 안전밸브의 조합체로 극저온의 산화제를 주입할 때와 비행 중에 기화된 산소기체를 배출시킨다. 벤트/릴리프밸브의 설계검증을 위해 AMESim과 FLUENT 상용코드를 이용하여 밸브모델을 구성하였다. AMESim 밸브모델을 검증하기 위해 밸브의 개폐압력, 개폐작동시간을 수학적 계산결과와 비교하였고 내부유동해석 결과를 반영하여 모델의 정확도를 높였다. 본 연구에서는 설계인자를 검증 및 작동성능을 분석하였다. 이 결과는 한국형 발사체에 사용되는 다양한 규격의 벤트/릴리프밸브 개발과정의 효율성을 높일 수 있을 것으로 판단된다.

• 한국추진공학회지
• /
• 제8권4호
• /
• pp.84-90
• /
• 2004

추진제 주입압력 350 psia 에서 0.95 lbf 의 정상상태 공칭추력을 내는 단일액체추진제 하이드라진 추력기의 성능평가 결과를 추력, 임펄스 비트, 비추력 등을 통하여 제시한다. 연소시험 형상과 절차에 대한 간략한 묘사와 더불어 정상상태 연소모드로부터 얻어지는 추진제 공급압력. 질량유량, 추력기 작동환경 진공도, 그리고 추력 등의 변이거동에 대한 전형적인 결과를 검토한다. 제시된 추력기 성능은 1-lbf급 표준형 단일추진제 로켓엔진의 기준성능에 성공적으로 비교된다. 선별된 추력기군을 위성체 추진시스템의 비행모델로 채택하기 위한 추력기간 성능편차에 대해 부연한다.