• Journal of Korean Society of Steel Construction
• /
• v.25 no.5
• /
• pp.497-507
• /
• 2013

This study investigated the tension-field action induced strip angle changes and deformed mode shapes of SPSW for high-rise structures subjected to lateral forces. Based on the numerical analysis 3, 9, 14 and 20 story structures, shear and flexural modes were identified by comparing the numerical analysis results to the predicted strength by theory. Shear deformation mode exhibited a constant angle in tension-field; whereas, flexural mode of the numerical results, differed from the tension-field action theory.

• Computers and Concrete
• /
• v.22 no.2
• /
• pp.167-182
• /
• 2018

The modeling of loss of bond between reinforcing bars (rebars) and concrete due to corrosion is useful in studying the behavior and prediction of residual load bearing capacity of corroded reinforced concrete (RC) members. In the present work, first the possibility of using different methods to simulate the rebars-concrete bonding, which is used in three-dimensional (3D) finite element (FE) modeling of corroded RC beams, was explored. The cohesive surface interaction method was found to be most suitable for simulating the bond between rebars and concrete. Secondly, using the cohesive surface interaction approach, the 3D FE modeling of the behavior of non-corroded and corroded RC beams was carried out in an ABAQUS environment. Experimental data, reported in literature, were used to validate the models. Then using the developed models, a parametric study was conducted to examine the effects of some parameters, such as degree and location of the corrosion, on the behavior and residual capacity of the corroded beams. The results obtained from the parametric analysis using the developed model showed that corrosion in top compression rebars has very small effect on the flexural behaviors of beams with small flexural reinforcement ratio that is less than the maximum ratio specified in ACI-318-14 (singly RC beam). In addition, the reduction of steel yield strength in tension reinforcement due to corrosion is the main source of reducing the load bearing capacity of corroded RC beams. The most critical corrosion-induced damage is the complete loss of bond between rebars and the concrete as it causes sudden failure and the beam acts as un-reinforced beam.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.5
• /
• pp.1179-1185
• /
• 2007

The study of girder-to-column joints under experiment and numerical analysis was carried out to evaluate change of the flexural capacity of the joints with the 2-layer upper reinforcement of girder within rectangular section and the single-layered upper reinforcement at the girder flange. According to the analysis results using the flange width, the flange thickness and the location of reinforcements in the upper flange as variables, in the models with a same effective width, the increasing rate of capacity has nothing to do with the flange width with a same effective width. However, the capacity of the models with the upper reinforcements arranged close to the rectangular beam section is larger than that of the models with the upper reinforcements arranged remotely from the rectangular section. If the range of arrangement fur reinforcement exceeds the effective width, despite of increasing the flange thickness, the capacity is not increased.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.5
• /
• pp.483-492
• /
• 2009

In this study, nonlinear analysis of steel plane frame was performed using the refined plastic hinge method of advanced analysis techniques. In deterioration of stiffness in plastic zone, influences by flexural bending, residual stress, geometrical non-linearity, and semi-rigid connection are considered. And also, further reduced tangent modulus was used for geometrical non-linearity, top and seat angle were chosen for semi-rigid connection. Furthermore, 3 parameter power model was used for moment-rotation behaviour of beam to column connection. The loading conditions are combined with axial and lateral force and the inverse triangle distribution of lateral and eight type of analytical models were used in analysis. The results of analyses were compared with semi-rigid and rigid connection on behaviour of numerical analysis models. And also, the behaviors of frame with changes of semi-rigidity were analyzed by using the results obtained from MIIDAS-GENw.

• Proceedings of the Korean Society for Quality Management Conference
• /
• 1998.11a
• /
• pp.680-695
• /
• 1998

The objective of this study is to optimize the responses of the creep feed ceramic grinding process simultaneously by an off-1ine multicriteria optimization methodology. The responses considered as objectives are material removal rate, flexural strength, normal grinding force, workpiece surface roughness and grinder power. Alumina material was ground by the creep feed grinding mode using superabrasive grinding wheels. The process variables optimized for the above objectives include grinding wheel specification, such as bond type, mesh size, and grit concentration, and grinding process parameters, such as depth of cut and feed rate. A weighting method transforms the multi-objective problem into a single-objective programming format and then, by parametric variation of weights, the set of non-dominated optimum solutions are obtained. Finally, the multi-objective optimization methodology was tested by a sensitivity analysis to check the stability of the model.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1994.04a
• /
• pp.73-80
• /
• 1994

This paper is to study the mechanical behavor and structural safety of the wire-mesh half slab by an analytical method. Layer model was adopted by modelling the wire-mesh half slab as a flexural member composed of free cantilever beam and vertical supports (walls or beams). Reasonable results for the prediction of ultimate strength of the half stab at each loading direction and design recommendations for the reinforcement detail at wall(beam)-slab joints are acquired. On the other hand, ductility capacity of the wire-mesh half slab was overestimated by not considering the brittleness of wire-mesh reinforcements pre-manufactured at the form of Kaiser Truss.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.159-164
• /
• 2001

In this study, a polymer mortar sandwich panel (PMSP) was developed : Core was made with the polymer mortar whose compressive strength was about 840 kgf/$\textrm{cm}^2$, and both facings were made with the glass fiber reinforced plastics (GFRP). The results showed that the strain energies and the ductility indices increased 16-340 times and 2-8 times, respectively, as the thicknesses of facings increased from 0.6 to 3.0mm with fixing the core thickness to constants (12-36mm). On the other hand, these values showed a tendency of decrease as the core thickness increased regardless of thickness of facings. A set of basic data for the structural analysis could be provided by investigating the correlations, within the scope of this research, between the resisting moment and the thicknesses of core and facings.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.105-110
• /
• 2002

In this study, a MMA modified polymer mortal sandwich panels was developed : Core was made with the MMA modified polymer mortar whose compressive strength was about 1020 kgf/cm$^2$, and both facings were made with the glass fiber reinforced plastics (GFRP). The results showed that the strain energies increased 20-33 times, respectively, as the thicknesses of facings increased from 1.50 to 2.76 mm with fixing the core thickness to constants (30-50 mm). On the other hand, these values showed a tendency of decrease as the core thickness increased regardless of thickness of facings. A set of basic data for the structural analysis could be provided by investigating the correlations, within the scope of this research, between the resisting moment and the thicknesses of core and facings.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.799-804
• /
• 2002

The compatibility of concrete repairs is proposed by D. Cusson et al. and N. K. Emberson et al. But this is the general compatibility of concrete repairs. This study is actualized the general compatibility of concrete repairs on the flexural specimen under bending load. This study is obtained following results. 1) As a results of analysis for repair effects on failure shape, debonding between concrete and repairs, yielding load and ultimate/yielding ratio, the repair effects is ascertained that the repair R3 is much excellent than the repair R7, but on the other hand R7 is very high than R3 on the viewpoint of compressive strength, where repair R7, R3 is a product. 2) Therefore the compatibility of concrete repair proposed by D. Cusson et al. and N. K. Emberson et al. must be reanalyzed for structures types of column, beam, wall, slab et al.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.259-264
• /
• 2002

This paper describes an attempt to develop a unified design approach for reinforced concrete short beam failing in shear based on a Arch Factor. Designing for short beam in shear is not as straightforward as designing for flexure due to the complicated interdependency of the variables involved and to the nonexistence of a rational theory tn current design code. Shear failure of reinforced concrete beams with stirrups is influenced greatly because of the actual geometrical shape(a/d) of the concrete and flexural reinforcement steel ratio, stirrup reinforcement ratio and concrete compression strength, size effect etc. The objective of this paper is to present a pilot study to develop a simplified physical model for estimating shear behavior of reinforced concrete short beams. The Key idea incorporated with this model is the Arch factor, introduced by Kim and White.