• Journal of the Korea Convergence Society
• /
• v.8 no.12
• /
• pp.391-395
• /
• 2017

In this research, we conducted a questionnaire survey of contents necessary for eyeglass dispensing & fitting fee and characterization solution of eyeglass dispensing & fitting fee. From August 1, 2016 to September 30, questionnaires were set up for 202 spectators of Seoul and Gyeonggi area, questionnaire survey was conducted online and offline. Statistical processing of all data was performed using Origin Pro 8.5. 92.1% (186 people) and 93.1% (188 people) were positively evaluating the necessity of introduction for the necessity of introducing eyeglass dispensing & fitting fee, respectively. The result suggested that it is necessary to establish the position of the optician as a medical service expert by providing a more stable policy through analysis of overseas cases of eyeglass dispensing & fitting fee.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.4 s.334
• /
• pp.45-52
• /
• 2005

This paper presents the characterization of through hole vias on printed circuit board (PCB) through the time domain and frequency domain measurements. The time domain measurement was performed on a single via using the TDR, and the model parameters were extracted by the fitting simulation using HSPICE. The frequency domain measurement was also performed by using 2 port VNA, and the model parameters were extracted by fitting simulation with ADS. Using the ABCD matrices, the do-embedding equations were derived probing in the same plane in the VNA measurement. Based on the single via characterization, the differential via characterization was also performed by using TDR measurements. The time domain measurements were performed by using the odd mode and even mode sources in TDR module, and the Parameter values were extracted by fitting with HSPICE. Comparing measurements with simulations, the maximum calculated differences were $14\%$ for single vias and $17\%$ for differential vias.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.18 no.1
• /
• pp.191-203
• /
• 2016

The 3D virtual fitting system is a new and very efficient system replacing real fitting in apparel industry and on-line shopping. It is a win-win system for both of consumer and manufacturer which not only reduces design and production time but also resolves consumer's complaints by checking the wearing image beforehand. It is a must-have item in the future. The purpose of this study is to analyze sizing menu, terms, and current status and to figure out problems of avatar sizing programs which substitute human bodies in virtual fitting. We chose three existing outstanding programs in domestic and global market, compared and analyzed the program, manual, and terms that are used in avatar sizing, and investigated the strengths, weaknesses, problems of options and terms and finally suggested an alternative terms. The revealed problems are as follows: each program supports various avatars ranging from male to female, from child to adult, and from oriental style to western style. The image of the avatar could be changed through the options for hair style, shoes and accessories. But we found out some problems. The avatar body types are far from actual human body types, avatar sizing menus and item terms are different from program to program, and terms not yet standardized. Cooperative efforts of industry and academy on standardization of sizing menus and terms should be emphasized for the virtual fitting system to be widely used like the other computer graphic programs or word editors.

• Journal of Korean Ophthalmic Optics Society
• /
• v.1 no.1
• /
• pp.73-84
• /
• 1996

Satisfactory for children's spectacles fitting can only be achieved with the resonable selection and assortment of frames of different pad shapes, size, materials, the general property of sample frame are flexibility for the temple. Loughness for bridge and variety for the length of temple, a selection of the lens is chosen usually by the characteristic of the power, safty, size and so on, it will be comport fit of frame controlled the hight and width of pad and angle of pad between the nose side, frontal angle of pad will be determinded that whether a frame may be capable of providing a comport fit. An important part of the fitting of spectacles is the final adjustment before the wearer takes them away, and also their continued adjustment to maintain the optimum comport and lens efficiency. It is suggested that spectacle adjustment is essentially a practical art that can only be acquired by continual practice.

• Korean Journal of Human Ecology
• /
• v.17 no.1
• /
• pp.115-126
• /
• 2008

The construction of an athlete's tight-fitting garments is very important to the wearer in terms of athletic performance. Therefore pattern development of tight-fitting garments must allow for the full range of human movement and postures. In this study the relationship between the construction of a skate pants pattern and clothing fitting was explored with the aim of improving the comfort of the clothing. The four male subjects were university students between the ages of 20 to 24. Subjective wear sensations of the experimental garments were rated using a seven-point Likert scale on four consecutive days. While wearing the garments, subjects were asked to take five different postures including waist flexion, sitting and others. A Likert-type scale was used for the evaluation, with 7 points indicating the best fit in tight-fitting pants. Results showed differences in the front-rise length and back-rise length between basic pants(A) and modified pants(B,C,D) were -5.16cm and +5.64cm. Comparing the basic pants pattern(A) with modified pants pattern(B), the latter was superior to basic pants(A) in terms of pressure sensation and closeness of fit, but there was no significant difference. Among the four tight-fitting skate pants, A and B pants were superior to the others in terms of fitting and stability of waist and hip sections. In the case of the skate pants, the number of cutting lines in the pattern had an influence on clothing comfort. A minimum cutting line for tight skate pants was better than a maximum cutting line in terms of clothing comfort.

• Fashion & Textile Research Journal
• /
• v.20 no.4
• /
• pp.410-421
• /
• 2018

The study is designed to develop a educational basic pants patterns for men, and has been analyzed focusing on the university textbooks published since 2000. We also used CAD programs and virtual fitting programs to analyze the fitness of pants. To do this purpose, after choosing 7 Men's Wear textbooks, selected patterns were drawn and measured using PAD system and were compared and analyzed. Also, the appearance evaluation was examined through virtual fitting and then evaluated 21 male and female university students in their 20s. After supplementing the problems of the patterns in the existing textbooks, a pattern was developed and verified the fitness of the developed pattern. The results of comparing the proposed measurement items of each textbook for the pants pattern indicated a significant differences in terms of hip circumference of each pattern, which were between 96~105cm. A comparison of the drafting methods of each pattern showed the drafting methods for the crotch length, the front crotch extension, the back crotch extension were the difference. The results of appearance evaluation were pattern E presented the slimmest fit and pattern D presented the loosest fit. As a result of analysis of pants pattern, a waist circumference 82cm, a hip circumference 98cm, a crotch length 24cm, a pants length 104cm and a ham line width 46cm were most suitable. The development pattern was evaluated as superior to the existing pattern through the appearance evaluation of the virtual fitting.

• Journal of Computational Design and Engineering
• /
• v.2 no.4
• /
• pp.218-232
• /
• 2015

Piecewise linear (G01-based) tool paths generated by CAM systems lack $G_1$ and $G_2$ continuity. The discontinuity causes vibration and unnecessary hesitation during machining. To ensure efficient high-speed machining, a method to improve the continuity of the tool paths is required, such as B-spline fitting that approximates G01 paths with B-spline curves. Conventional B-spline fitting approaches cannot be directly used for tool path B-spline fitting, because they have shortages such as numerical instability, lack of chord error constraint, and lack of assurance of a usable result. Progressive and Iterative Approximation for Least Squares (LSPIA) is an efficient method for data fitting that solves the numerical instability problem. However, it does not consider chord errors and needs more work to ensure ironclad results for commercial applications. In this paper, we use LSPIA method incorporating Energy term (ELSPIA) to avoid the numerical instability, and lower chord errors by using stretching energy term. We implement several algorithm improvements, including (1) an improved technique for initial control point determination over Dominant Point Method, (2) an algorithm that updates foot point parameters as needed, (3) analysis of the degrees of freedom of control points to insert new control points only when needed, (4) chord error refinement using a similar ELSPIA method with the above enhancements. The proposed approach can generate a shape-preserving B-spline curve. Experiments with data analysis and machining tests are presented for verification of quality and efficiency. Comparisons with other known solutions are included to evaluate the worthiness of the proposed solution.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.8
• /
• pp.49-58
• /
• 2004

The cone pressuremeter test (CPM) is a new in-situ test which combines a standard cone penetration test with a pressuremeter. The cone pressuremeter tests in clay are presented and analyzed. An analytical solution of CPM incorporated non-linear soil behavior with no volume change is presented, and curve fitting technique is proposed to make use of both the loading and unloading portions of the pressuremeter test. The proposed method is accomplished by putting greater emphasis on the unloading portion. Twenty CPM tests are analyzed using the proposed method, and the derived undrained shear strength of soil is compared with other tests such as field vane tests and laboratory tests. The interpreted soil parameters had resonable values when compared to other in-situ and laboratory test results. The cone pressuremeter has provided reliable measures of undrained shear strength using curve fitting method.

• Korean Journal of Human Ecology
• /
• v.15 no.3
• /
• pp.481-490
• /
• 2006

Adjusting pressure level in the construction of athletes' tight-fitting garments by reducing the elastic knit pattern is a challenging subject, which influences the performance of the wearer directly. Therefore, in this study, relationship between the reduction rates of the basic pattern obtained from 3D human scan data and resultant clothing pressure was explored to improve the fit and pressure exerted by clothing. 3D scan data were obtained using Cyberware and they were transformed into a flat pattern using software based on Runge-Kutta method. Reduction rate was examined by subjective wear test as well as objective pressure measurement. As a result, difference in the length between the original 3D body scan data and the 2D tight-fitting pattern was 0.02$\sim$0.50cm (0.05$\sim$1.06%), which was within the range of tolerable limits in making clothes. Among the five garments, the 3T-pattern was superior in terms of subjective sensation and fit. The pressure of the 3T pattern was 2$\sim$4 gf/cm2 at five locations on the body, which is almost the same or a bit higher than that of Z-pattern. In the case of tight-fitting overall garment, the reduction rate of the pattern in the wale direction is more critical to the subjective sensation than the course direction. It is recommended that the reduction grading rules of course direction should be larger than that of Ziegert for a better fit of tight-fitting garments. In the case of wale direction, however, reduction grading rule should be kept the same as suggested earlier by Ziegert (1988).

• Journal of Korea Multimedia Society
• /
• v.15 no.7
• /
• pp.941-950
• /
• 2012

A virtual garment fitting system which fits the top and bottom of a garment on 3D body data is introduced. This system uses the laser scanned 3D body data and the digital images photographed the front and back of a garment. The digital images are modeled to reflect tensions among particles in the images and the friction and gravity effects are considered in the fitting process to the body data. When a bottom is fitted, a virtual belt to hold the bottom in the waist is introduced since gravity effects pull down it. Also the process for fitting the top and bottom on layers is proposed here. The system has the strengths that it uses only the front and back image of a garment instead of using complicated patterns of a garment, and provides a realistic fit result as a 3D figure. As on-line retailing shop in present displays front and back images of garments, this system also does. However this system provides a differentiated service to user than present retailing shop as showing a 3D fit image. It will make a new trend in online shop retailing of garment.