• Journal of the Korea Safety Management & Science
• /
• v.22 no.2
• /
• pp.47-55
• /
• 2020

This study analyzed ignition probability about Lithium-polymer batteries of what variously were being produced wearable devices recently. The study analyzed ignition probability by PCM(Protection Circuit Module) operating state and overcharged, over-discharged, exposed to high temperatures of Lithium polymer batteries, analyzing wearable devices on the market. Then it classified experimental results to implement analysis comparison about weight, X-ray imaging, battery decomposition. With these experiments, the study analyzed combustion-possibility and fire patterns. These statistics will be used to measure and verify the cause of a fire when identify wearable devices using Lithium-polymer batteries.

• Fire Science and Engineering
• /
• v.29 no.6
• /
• pp.119-128
• /
• 2015

A fire broke out in a working wood-burning stove and destroyed an idyllic house about two years after it was built. This study analyzed data provided through the court by the fire station, police station, fire insurance investigation agency, house construction company, and wood-burning stove maker Based on the fire pattern of low-temperature long-term ignition that remained in the studs, the fire was found to be caused by the conduction of heat in the fire box to the studs of the wall next to the wood-burning stove. A fire simulation showed that the low-temperature long-term ignition of the studs next to the wood-burning stove occurred because a hole was not made for ventilation in the chimney.

• Fashion & Textile Research Journal
• /
• v.13 no.4
• /
• pp.624-634
• /
• 2011

The purpose of this study is to develop the pattern of safety clothes used at flat or mountainous areas and to identify the pattern of safety clothes by conducting experimental evaluation of virtual wear. Three subjects were selected, based on fire fighters' physical constitution. A prototype design for safety clothing was determined after in-depth interviewing of professionals and surveying of Forest service staff and related agency. Wearing test should be carried out in the order of pattern making, virtual and real wearing evaluation. For data analysis, technical statistical values should be obtained by using body measurements of subject, frequency analysis and T-test. The jacket is designed to have a front extension and the entire length of clothing enough for wearer to put on it over ordinary shirts or sweater. The collar of jacket is of round type. Cyber reality enables to identify the movement and activity of virtual fitting model and to find out errors or problems in safety clothing prior to on-the-spot wear test, thus raising the precision level of pattern. There was significant difference between real and virtual fit preference. The results show that the virtual try-on system need the development of a specific style.

• Journal of the Korea Safety Management & Science
• /
• v.10 no.4
• /
• pp.105-109
• /
• 2008

The purpose of this study is to distinguish the causes of broken glass on doors or windows when it is originally kept among the remains on the floor in fire site - whether it was broken due to heating or outer power-through test and characteristics of the broken plane including the pattern on the plane. Addition to it, the study tries to find characteristics to judge the point and direction of breakdown through the analysis of glass broken by outer power. With two assumed causes - a) breakdown due to heating and b) breakdown due to outer power-3 pieces of glass plates ($30cm{\times}30cm{\times}5mm$) were tested for each case, getting the results as following: First, for the glass broken due to the change of temperature, the broken plane is of slow and smooth curve without any pattern. Second, for the glass broken due to outer power, with the impact point as the center, the glass shows breakdown of radial type and the side shows breakdown of near-perpendicular type. The far the broken piece is from the impact point, the bigger the size is. The broken piece at the impact point is of long triangle type and the two long planes of the triangle shows semi-arc with the center of breakdown point and the other plane shows opposite pattern. Third, when glass that is damaged by outer power is heated, damaged forms and side patterns of the glass that is damaged by outer power are heated and disappeared.

• Journal of the Korean Society of Safety
• /
• v.30 no.6
• /
• pp.40-47
• /
• 2015

In this study, temperature characteristics and fire damage form were analyzed to investigate flame spreading form and fire probability from ignition sources subject to drivit component materials which is finishing material in architecture. Ignition sources were limited to a gas torch and exterior panel board fire, and the size of the sample was manufacture in 30 cm length ${\times}$ 50 cm height ${\times}$ 5cm thickness size. Marble (inner wall) + 3 mm drivit (outer wall), marble (inner wall) + 4 mm plaster stone (outer wall), sandwich panel + 3 mm driver bit (outer wall), sandwich panel + 3 mm driver bit + insulation (outer wall), and gypsum board (inner wall) + 3 mm drivit (outer wall) were prepared for the sample. As result of the research for temperature characteristics, large temperature difference by each material was shown in $218^{\circ}C{\sim}995^{\circ}C$ at 30 seconds and $501^{\circ}C{\sim}1078^{\circ}C$ at 300 seconds. Especially when the inner wall was a plaster board, lowest temperature of $501^{\circ}C$ was shown at 300 seconds and marble inner wall showed the following lowest temperature of $900^{\circ}C$. Temperature rising over $1000^{\circ}C$ was shown in other materials. Regarding fire damage form, drivit or gypsum board outer wall parts exposed to fire showed combustion and carbonization to show calcination(breaking phenomenon) and influence of heat exposure was higher as calcination became more severe.

• Fire Science and Engineering
• /
• v.34 no.4
• /
• pp.101-106
• /
• 2020

This study analyzed flame growth characteristics and carbonization patterns when floor materials were burned vertically using a needle flame produced for this study. It was found that PVC flooring was fire retardant and the area under direct flame contracted inward. Vertical combustion causes solidification in the form of a lump at the bottom and also generates soot in a pattern that progresses upwards. This study found that laminated flooring exhibited no fire retarding characteristics and that the laminated layer of its upper surface was destroyed by fire, causing irregular delamination. The carbonization ranges at the left and right sides were determined to be symmetrical. A vertical combustion test of a sample carpet showed that it exhibited no fire-retarding characteristics. It was observed that if heat accumulated in the carpet, the flame formed an ascending air current, and that when flammable materials were present around the flame, they further accelerated the diffusion of the flame. The carbonization pattern at the carpet surface exposed to direct flame revealed that the carpet surface had melted and had flown downwards and that many tiny holes formed on it.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2012.04a
• /
• pp.167-169
• /
• 2012

본 연구는 정수기 화재의 원인 판정을 위한 지식기반을 구축하기 위해서 인위적 착화가 발생했을 때의 연소 확산 패턴을 해석하였다. 실험이 재현되는 동안 외부에서 인위적인 에너지의 공급은 없었으며, 정수기는 정상 작동 상태를 유지시켰다. 인위적 화염으로 착화되어 50[sec] 경과하였을 때까지 불꽃은 외부에서 관측되지 않았다. 그러나 120[sec] 정도 경과되었을 때 일순간 화염은 확산되기 시작하였으며, 부분적인 소락이 발생되는 것이 관측된다. 화염이 180[sec] 동안 진행되었을 때 강제로 진압된 후 연소패턴 분석에서 최초의 착화점을 기준으로 정확한 브이패턴(V-pattern)이 형성되었으며, 외부에서 화염이 공격되었을 때와 확연한 차이가 있음을 알 수 있다. 또한 정수기 후면에 설치된 방열판의 열화 특성 분석에서 화열의 공격방향 판정이 가능한 것을 알 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.270-273
• /
• 2001

Electrical tree is studied widely by manufacture state of insulating material fare and blazing fire diagnosis system of use in phenomenon of part discharge that happen for main cause of dielectric breakdown of equipment for electric power. Use process that draw tree pattern here measuring above zero to study special quality of this electricity tree, real-time processing by image processing is proposed because reproduction of tree blazing fire process drops and pattern of tree is difficult correct quantification of tree growth by existent visual observation by involution. This research presents general process that need in image processing of tree blazing fire, and that remove various noises that happen in above zero by measuring electrical tree dividing background and complete view in measured above zero taking advantage of specially proposed complete view object abstraction techniques effectively and quantification of tree becomes easy naturally, can apply to dielectric breakdown estimate because can chase growth process of tree.

• Fire Science and Engineering
• /
• v.23 no.1
• /
• pp.15-20
• /
• 2009

For the effective management of forest fire, understanding of regional forest fire patterns is needed. In this paper, forest fire ignition and spread characteristics were analyzed based on forest fire statistics. Fire occurrences, burned area, rate of spread, and burned area per fire between 1991 and 2007 were parameterized for the cluster analysis, which results were displayed using GIS to detect spatial patterns of forest fire. Administrative districts such as cities and counties were classified into 5 clusters by fire susceptibility. Metropolitan areas had fire characteristics that were infrequent, slow rate of spread, and small burned area. However, 4 cities and counties showing fast rate of spread, and large burned area, in the eastern regions of Taeback Mountain range, were the most susceptible areas to forest fire. The next vulnerable cities and counties were located in the West and South Coast area.

• Fire Science and Engineering
• /
• v.23 no.2
• /
• pp.96-100
• /
• 2009

Because of dense forests and restriction of approaching for fire fighters, forest fire is easy to be a larger fire in Korea. For this result, the air attack was about 90% of extinguishing, so the application of aircrafts, especially helicopters, will be increased gradually. In the all process of forest fire attack, the method of heli-scattering water was the chief element of success of efficient forest fire attack and safe flight. Therefore, a standardized method of heli-scattering water was required. However, as it was not already standardized, a efficiency and safety of fire fighting have been decreased. In this study, we suggest a 11 patterns of methods for scatterling water based on a actual experience of air attack.