• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.03a
• /
• pp.101-109
• /
• 1996

Mini-mill process which is one of the new steel -marking technologies to be able to produce the hot rolled coils by thin slab caster of ISP(In-Line Strip Production) type, will be completed in the Kwangyang Steel Works of POSCO in August, 1996, SEt-Up Model of finishing mill which consists of 5 stands is the most basic and essential in mini-mill plant. Therefore, the simulation program of Finishing-mill Set-Up model were developed in this research , using new temeprature prediction model, roll gap model and rolling physical model. Using the developed FSU program , pass schedules to produce the strips with target strip thickness of 1.8mm, 2.0mm, 2.3mm, 2.7mm an d3.0mm were also determined respectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.89-96
• /
• 2000

This paper describes the characteristic of die finishing to obtain smooth surface using electro-chemical grinding after cutting process. Electro-chemical grinding is possible under lower load and tool wear comparing with those in the mechanical grinding. Conventionally, if the metal bonding material of the grinding wheel is directly t contacted with workpiece, the current is circulated without electrolytic phenomena. Sometimes, electrical discharge is occurred between tool and workpiece. To cope with this problem, the metal-resin bonded pellet was used in this study. This pellet is composed of optimal volume of metal and resin powders and its characteristics are changable with the each volume of powders. Finally, high efficient die finishing is realized using metal resin bonded pellet in electro-chemical grinding.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1994.10a
• /
• pp.387-392
• /
• 1994

Recently, as the problems according to lack of skilled labour and superior construction materials were gathering strength, there were required the advent of a special materials in building construction division. As a view of the point, the cement-based Self leveling mortar was developed for improvements of the former problems. The Self leveling mortar has the all kinds of the properties as followed the premixed products in plant, self-smoofhing, non shrinkgae etc, accordingly the finishing of concrete floor don't need skilled labour. The purpose of this study is to establish the introduction of a finishing construction method for concrete floor and slab using the cement-based self leveling mortar. Presented is a study on the basic properties of fresh and hardened self leveling mortar. To this end, an actual floor's finishing construction using the cement-based self leveling mortar was conducted in approximately 1,800㎡ floor as to compare the flatness and levelness after finighing.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2004.05a
• /
• pp.161-166
• /
• 2004

In recent years, living space of modern society have vared, and new methods to build have been introduced using new building materials and interior finishing materials as the life level is enhanced. But these kinds of materials release some harmful substances to people. The most of people living in new apartment have headache and dizziness, and feel sick of the stomach, sleepiness, eye stimulus, concentration decrease and allergies. That called 'sick house syndrome'is becoming new society problem. The purpose of this study is to investigate the kinds and various problems of the interior finishing materials and to pursue improvement of living place and pleasant interior surroundings.

• Textile Coloration and Finishing
• /
• v.31 no.4
• /
• pp.258-267
• /
• 2019

Synthetic suede without PFCs(perfluorinated compounds) are followed by subsequent high temperature treatment. But migration fastness of synthetic suede may be reduced due to sublimation of disperse dyes that results from the high temperature treatment. Therefore, in this study, chitosan treatment was used to improve the migration fastness before polyurethane dipping process. Polyester fiber was treated with sodium hydroxide aqueous solution before chitosan processing. This samples treated with a chitosan concentration upto 0.5% were dyed and coated with PUD(polyurethane dispersion). The migration fastness was most improved at 0.35% application. This is presumably due to the fact that the chitosan may increase the dye-binding capability through intermolecular hydrogen bonding.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.11
• /
• pp.47-56
• /
• 2013

Rolling speed, roll gap, and cooling pattern in hot strip finishing mill process should be determined before inserting strip into roll. Such parameters are initially calculated by a mathematical set-up model. The technique to find adequate roll speed via a mathematical model has inherently limit because required working conditions are various and rolling process is nonlinear. To improve the accuracy of initial rolling speed for a finishing mill, this paper suggests a correction technology for initial rolling speed. The proposed method was implemented in hot strip mill process. As the results, the magnitude of width error in strip head-end part caused by excessive strip tension was decreased remarkably.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.4
• /
• pp.296-303
• /
• 2007

This paper proposes a new width control system composed of an ANWC(Automatic Neural network based Width Control) and a fuzzy-PID controller in hot strip finishing mills which aims at obtaining the desirable width. The ANWC is designed using a neural network based width prediction model to minimize a width variation between the measured width and its target value. Input variables for the neural network model are chosen by using the hypothesis testing. The fuzzy-PlD control system is also designed to obtain the fast looper response and the high width control precision in the finishing mill. It is shown through the field test of the Pohang no. 1 hot strip mill of POSCO that the performance of the width margin is considerably improved by the proposed control schemes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.83-86
• /
• 1997

Even as many methods and technologies have been introduced on data generation, parts orientation and layer slicing to acquire the rapid prototyping(RP) parts that have useful surface to satisfy customers' needs such as stylingldesign verification directionlindirect tooling directly from the RP machine, these trials continue to suffer from the surface roughness due to the build characteristics of RP technology. A new postprocess finishing method is suggested in this paper to overcome the surface roughness problem on the surface of the RP parts. To prevent deterioration of dimensional accuracy from the conventional grinding-only, and coating-grinding methods, 4-step surface finishing process is applied. To satisfy the various requirements from the RP oriented industrial f elds, effective procedure, coating material, grmd~ng tools and methods are employed.

• Textile Coloration and Finishing
• /
• v.3 no.4
• /
• pp.7-12
• /
• 1991

Wool gabardines were treated with alkaline proteases, and their tensile strerigth and dyeing behavior were obtained. Enzylon ASA 30 and Alcalase 2.5L DX did not show much effect on the weight loss of wool, but Esperase 8.0L decreased the weight of wool to a great extent. Pretreatment of wool with dichloroisocyarturic acid before protease-treatment increased the weight loss of wool considerably. Weight loss was accompanied by serious strength decrease and the use of sodium sulfate in the protease-treatment had not effect on the strength retention, only lowering the weight loss of wool. Protease-treatment of wool increased dyeability considerably, which may be due to the change in the inner structure of wool fiber by protease.

• Textile Coloration and Finishing
• /
• v.9 no.4
• /
• pp.20-27
• /
• 1997

As a non-aqueous dyeing method, organic solvent dyeing was discussed, The dye uptakes on PET and the solubilities of C. I. Disperse Violet 1 in 24 kinds of organic solvents including water were investigated, and the partition coefficients in PET- solvents system were also obtained from their isotherms. Contrary to in the other solvents, the dye uptake of C. I. Disperse Violet 1 on PET in hexane was even much higher, and also considerable in cyclohexane. The logarithmic plot of the dye uptakes versus the solubilities showed that the dye uptakes are linear and inversely proportional to the solubilities. The effect of $T_g$ decrease of PET in organic solvents to dye uptake seems to be very small relative to the effect of solubility, and so negligible.