• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.84-87
• /
• 2003

Microstructural evolution and dry sliding wear behavior of ultra-fine grained 5052 Al alloy obtained by an accumulative roll-bonding process have been investigated. After 7 ARB cycles, ultra-fine grains with large misorientations between neighboring grains were obtained. The grain size was about 0.2$\mu\textrm{m}$. The hardness, tensile and yield strengths of the ultra-fine grained alloy increased as the amount of accumulated strain increased with the ARB cycles. Sliding wear teats of the ultra-fine grained 5052 Al alloy were conducted at room temperature. Wear rate of the ultra-fine grained alloy increased in spite of the increase of hardness. Surfaces of the worn specimens were examined with SEM to investigate wear mechanism of the ultra-fine grained alloy.

• 소성∙가공
• /
• 제12권4호
• /
• pp.376-381
• /
• 2003

Microstructural evolution and dry sliding wear behavior of ultra-fine grained 5052 Al alloy obtained by an accumulative roll-bonding process have been investigated. After 7 ARB cycles, ultra-fine grains with a large misorientation between neighboring grains were obtained. The grain size was about 0.2 $\mu$m. The hardness, tensile and yield strengths of the ultra-fine grained alloy increased as the amount of accumulated strain increased with the ARB cycles. Sliding wear tests of the ultra-fine grained 5052 Al alloy were conducted at room temperature. Wear rate of the ultra-fine grained alloy increased in spite of the increase of hardness. Surface of the worn specimens were examined with SEM to investigate wear mechanism of the ultra-fine grained alloy.

• 한국안전학회지
• /
• 제22권2호
• /
• pp.15-21
• /
• 2007

Fine grained Al-5083 alloy produced by equal channel angular pressing (ECAP) at $120^{\circ}C$ was tested for investigating mechanical properties and crack growth propagation behavior. Also, FEM stress and strain analysis for the samples during ECAP were investigated, using a plastic deformation analysis software DEFORM 2-D. Coarse grained as-received samples exhibited UTS of 255.6MPa with a elongation to failure of 34.4%. By contrast, the ECAPed fine grained samples exhibited UTS of 362.0MPa with a elongation to failure of 12.9%. Fatigue crack growth resistance and threshold of fine grained samples were lower than that of as-received coarse grained samples. The higher fatigue crack growth rate in the fine grained ECAPed samples may partially arise from small roughness closure effect due to smoother fracture surfaces.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.1192-1201
• /
• 2009

The ground work with of the research is constructed by a SCP method to improve clay ground in the sedimentary layer and sand ground in the reclamation layer at the same time as a reclaimed soft ground by reclaiming deep depth. Improved fine-grained soils in the sand ground decrease the ground improvement effect and have an influence on replacement ratio of SCP method. Fine-Grained soils which advances in sand ground reduces a from improvement effect, Makes affect in replacement ratio of SCP method. In this study, consideration about replacement ratio of sand ground, Tried to observe affects in replacement ratio of fine-grained soils SCP method of dredging reclamation ground. The result, replacement ratio which follows in the Japan Geotechnical Society experience-chart(1988) recording where fine-grained soils content will increase feebly, was visible the aspect which increases progressively, replacement ratio in compliance with Gibbs and Holts(1973) methods according to fine-grained soils increase is visible the tendency which decreases gradually with the enemy. Specially, according to case fine-grained content of Mizuno(1987) methods increases, replacement ratio suddenly was showing the trend which rises from of 50% and according to fine-grained soils increase was overestimated.

• Journal of the korean society of oceanography
• /
• 제32권3호
• /
• pp.128-137
• /
• 1997

This study presents results from a detailed sedimentological investigation of surface sediments obtained from the Korea Strait region, the southern part of the East Sea (Sea of Japan). The distribution of different types of bottom sediments is controlled by the recent fine-grained sediment transport and deposition combined with the lowerings of sea level during the last glacial period, forming a diverse mixture of organic-rich fine-grained and shelly coarse-grained sediments. In comparison to high organic concentration of fine-grained sediments in the inner continental shelf and slope areas, the shell-rich coarse-grained sediments on the outer shelf are discernible being further modified. These coarse-grained sediments are confirmed as relict resulting from the sediment dynamics during the lower sea levels of the last glacial period. Clay mineral distribution of the fine-grained sediments gives information about the transport mechanism. Presence of present-day current system (the Tsushima Warm Current) is most probable source for the fine-grained particles into the open East Sea from the East China Sea, indicating that Holocene sediment dynamics may be used to explain the observed distribution of surface coarse-grained shell-rich sediments.

• 한국지반환경공학회 논문집
• /
• 제16권11호
• /
• pp.39-43
• /
• 2015

본 연구에서는 압밀 배수를 촉진하기 위한 공법에서 사용되는 조립토나 골재로의 세립토 관입 정도를 다양한 조건에서 실험을 통해 확인하여 세립토의 조립토나 골재로의 관입특성을 규명하였다. 지중응력에 대응하는 압력의 크기나 세립토 함수비의 변화에 상관없이 해성점토가 해사나 표준사로는 관입되지 않아 모래 배수/말뚝 체에서의 배수저항 현상은 전혀 발생하지 않은 것으로 확인되었고, 오히려 물다짐에 의한 모래 배수/말뚝 체의 전단강도가 크게 증대한 것으로 보인다. 골재의 경우에는 골재의 입경이 클수록 해성점토의 관입깊이는 증대하고, 같은 골재라도 압력이나 함수비가 클수록 해성점토의 관입깊이는 증대함을 알 수 있었으며, 액성한계보다 작은 함수비를 갖는 해성점토는 입자가 작은 편인 13mm 골재로의 관입깊이가 현저하게 줄어들어 그 관입깊이가 상당히 적다 하더라도 일단 관입된 세립토에 의해 배수/말뚝 체에서의 배수저항 현상이 발생할 것으로 사료된다. 따라서 자연함수비가 액성한계보다 큰 매우 연약한 세립토층에서는 모래보다 큰 입경을 갖는 쇄석이나 자갈 등 골재를 사용하는 gravel drain 공법 및 gravel compaction pile 공법 등의 적용을 지양해야 하고, 자연함수비가 액성한계보다 작은 연약한 세립토 지반에서도 gravel drain 공법 및 gravel compaction pile 공법 등과 같은 연직배수공법을 적용할 경우 그 효용성은 크게 저하할 것으로 사료된다.

• Geomechanics and Engineering
• /
• 제33권2호
• /
• pp.183-194
• /
• 2023

This study presents the prediction of the California bearing ratio (CBR) of coarse- and fine-grained soils using artificial intelligence technology. The group method of data handling (GMDH) algorithm, an artificial neural network-based model, was used in the prediction of the CBR values. In the design of the prediction models, various combinations of independent input variables for both coarse- and fine-grained soils have been used. The results obtained from the designed GMDH-type neural networks (GMDH-type NN) were compared with other regression models, such as linear, support vector, and multilayer perception regression methods. The performance of models was evaluated with a regression coefficient (R²), root-mean-square error (RMSE), and mean absolute error (MAE). The results showed that GMDH-type NN algorithm had higher performance than other regression methods in the prediction of CBR value for coarse- and fine-grained soils. The GMDH model had an R² of 0.938, RMSE of 1.87, and MAE of 1.48 for the input variables {G, S, and MDD} in coarse-grained soils. For fine-grained soils, it had an R² of 0.829, RMSE of 3.02, and MAE of 2.40, when using the input variables {LL, PI, MDD, and OMC}. The performance evaluations revealed that the GMDH-type NN models were effective in predicting CBR values of both coarse- and fine-grained soils.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.889-890
• /
• 2006

In recent years, PCB drills with smaller diameters less than 0.1 mm are used and thus there are growing needs for ultra-fine grained cemented carbides. However, ultra-fine WC powder usually causes extraordinary grain growth during sintering which weakens mechanical strength of ultra-fine grained cemented carbides. So we examined several kinds of WC powders to make new ultra-fine grained cemented carbides having superior performance. We found that direct carburized WC powder is very good as a WC raw material. The PCB drills made of the developed ultra-fine grained cemented carbides have higher hardness, toughness and stiffness than conventional ones.

• Tribology and Lubricants
• /
• 제14권4호
• /
• pp.114-120
• /
• 1998

The T-curve, wear and erosion behaviors of two different silicon carbides, i.e., the fine grained SiC and the in situ-toughened SiC(IST-SiC). Both materials exhibited an increasing T-curve behavior, although the T-curve of IST-SiC was steeper than that of fine grained SiC. The fracture toughness of IST-SiC was larger than that of fine grained SiC at long crack regime, whereas an opposite tendency occurred at short crack regime. The rate of material removal during wear and erosion tests was higher in IST-SiC compared to fine grained SiC. The difference between the material removal rates of two materials was discussed in the light of their R-curve behaviors.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.139-145
• /
• 1998

This paper addresses the R-curve properties, wear resistance, and erosion resistance of the two silicon carbide ceramics with different microstructures, i.e. , fine grained SiC and in situ-toughened SiC(IST SIC). Fine grained SiC exhibits a relatively flat R-curve behavior whereas the IST SiC exhibits a increasing R-curve behavior. The increasing R-curve behavior in IST SiC is attributed to relatively weak grain boundaries. The rate of material removal during wear tests and erosion tests was higher for IST SiC than that for fine grained SiC. This is attributed to the weaker grain boundaries in IST SiC than that in fine grained SiC. It is implied that fracture toughness in short crack regime should be taken into consideration in the interpretation of the microscopical material removal process. We show that the higher the strength of grain boundaries is, the higher wear and erosion resistances are.