• Journal of The Geomorphological Association of Korea
• /
• v.17 no.1
• /
• pp.15-27
• /
• 2010

This study investigated the sedimentary environment changes in the Baramarae beach of Anmyeondo through spatio-temporal surface sediment analysis. In the winter season 2009, surface sediments were classified into 7 sedimentary facies such as gravel, sand, gravelly sand, gravelly muddy sand, muddy sand, silty sand, and sandy silt. Time-series analysis of average grain size from 2002 to 2009 revealed that the average grain size of sediments became finer and sorting was much worse. On the contrary, during the same period, the grain size became coarsening-trend and sorting was much better in beach area. These different grain size patterns resulted from the different change characteristics of beach and tidal flats. The southwestern beach area was connected to the open sea and thus fine sediments were removed by the environments with relatively high-energy. The sedimentation of fine sediments in the bay resulted from the tidal current action and the reduction of energy by the topographic effects. Fine sediments in the outer part of southwestern tidal flats could be explained such that the Seomot isle blocked ocean waves and as a result, low-energy environments accelerated sedimentations of fine sediments.

• Journal of the Korean Ceramic Society
• /
• v.31 no.8
• /
• pp.849-860
• /
• 1994

The microstructural evolution and crystalline phases of this infiltration of Ti+Al liquids in TiC, SiC, TiC+C, and SiC+C preforms have been investigated. As the Ti and Al mixing ratio in Ti+Al infiltrated liquid changes, the newly formed reaction products, which were reacted from the Ti+Al liquid with preforms, consisted of three major phases as Ti3AlC, Al2Ti4C2 or Al4C3. The TiC grain shape was changed to spheroid, when Ti3AlC was formed. In case of Al2Ti4C2 formation, the platelet grain was formed from the original TiC grain. When Al4C3 was formed, nodular or intergranular fine-grained Al4C3 was formed around the TiC grain, while the original TiC grain shape was not changed.

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.551-558
• /
• 1998

Detection of microcrack in {{{{ {Al }_{2 } {O }_{3 } }} ceramics were studided by AE(acoustic emission) technique with 4-point bending test in order to evaluate the fracture process and formation of microcrack. Fully-dense alu-mina ceramics having a different grain size were fabricated by varing the hot-pressing temperature. The grain size of alumina increased with increasing the hot-pressing temperature whereas the bending strength decreasd. The microcracks were observed by SEM and TEM. The generation of AE event increased with increasing the applied load and many AE event was generated at maximum applied load. Alumina with smaller grain size shows the generation of many AE event resulting in an increase of microcrack formation. An intergranular fracture is predominantly observed in fine-grained alumina whereas intragranular fracture occurs predominantly in coarse-grained alumina,. Analysis of micorstructure and AE prove that primary mi-crocracks occur within grain-boundaries of alumina. The larger microcracking were formed by the growth and/or coalesence of primary microcracks. Then the materials become to fracuture by main crack gen-eration at the maximum applied load.

• Transactions of Materials Processing
• /
• v.29 no.1
• /
• pp.5-10
• /
• 2020

Heat treatment conditions of 88.5% asymmetrically cold rolled oxygen free copper (OFC) sheets have been studied to obtain an equiaxed fine microstructure with a grain size of less than 10 ㎛. The commercial OFC sheets with the thickness of 10 mm were asymmetrically cold rolled by using equal speed asymmetric rolling (ESAR) processes and total rolling reduction. The thickness of the rolled sheets were 88.5% and 1.15 mm, respectively. An equiaxed fine microstructure of OFC sheets with a grain size of 6.0 ㎛ were obtained when the asymmetrically cold rolled OFC sheets were heat treated at 180℃ for 40 minutes. The tensile strength of the asymmetrically cold rolled specimen increased from 217.6 MPa to 396.1 MPa, while the elongation of the specimen asymmetrically cold rolled and heat treated increased from 29.0% to 66.9% along with an 8% increase of the tensile strength.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.52 no.2
• /
• pp.134-139
• /
• 2007

The research was conducted with the aim of determining effects of seedling age on the yield of four fine rice varieties viz., Kalizura, Tulshimala, BRRI (Bang-ladesh Rice Research Institute)-37 and BRRI-38. The seedling of different ages such as 15, 25, 35 and 45 days were transplanted on the same day maintaining $25cm{\times}15cm$ spacing. The experiment was laid out in a randomized complete block design with three replications. The yield and yield contributing characters were influenced by seedling age, variety and their interaction. BRRI-38 gave the highest number of effective tillers $hill^{-1}$, panicle length, total spikelets $panicle^{-1}$, grains $panicle^{-1}$, 1000-grains weight and grain yield. Likewise, yield and yield contributing characters were the highest in 35 days old seedling. On the other hand, the variety (BRRI-38) with the same age as of seedlings 35 days old seedlings was found superior to other interactions, but, in the production of grains $panicle^{-1}$ and 1000-grains weight there was no significant effect in this interaction. From the findings it may be inferred that BRRI-38 with 35 days old seedlings produced the highest grain yield.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.2
• /
• pp.81-92
• /
• 1997

The effect of alloying elements, precipitate size, its distribution, and dislocation substructure resulted from warm rolling or cold rolling in the superplastic Al-Mg alloy system was investigated. One of the major requirements for fine structure superplasticity is that the grain size should be very small. Fine grain structure is controlled by the dislocation substructure and the dynamic recrystallization during hot or warm working. The recovery of Al-Mg base alloys was constrained resulting in relatively high dislocation density when the alloys were warm rolled. In particular, Al-Mg-Zr alloy exhibited the smallest sub-grain size among Al-Mg alloys containing Mn, Cu, Zr as a third element. The Al-Mg-Mn alloy cold rolled 80% after hot rolling showed the maximun strain rate sensitivity exponent, m, of 0.75 under strain rate of $7.1{\times}10^{-4}/s$ at $500^{\circ}C$. The elongation of the alloys was limited in spite of high m values due to large dispersoids containing appreciable amount of Fe impurities.

• Journal of Powder Materials
• /
• v.24 no.2
• /
• pp.108-114
• /
• 2017

We fabricate fine (<$20{\mu}m$) powders of $Bi_{0.5}Sb_{1.5}Te_3$ alloys using a large-scale production method and subsequently consolidate them at temperatures of 573, 623, and 673 K using a spark plasma sintering process. The microstructure, mechanical properties, and thermoelectric properties are investigated for each sintering temperature. The microstructural features of both the powders and bulks are characterized by scanning electron microscopy, and the crystal structures are analyzed by X-ray diffraction analysis. The grain size increases with increasing sintering temperature from 573 to 673 K. In addition, the mechanical properties increase significantly with decreasing sintering temperature owing to an increase in grain boundaries. The results indicate that the electrical conductivity and Seebeck coefficient ($217{\mu}V/K$) of the sample sintered at 673 K increase simultaneously owing to decreased carrier concentration and increased mobility. As a result, a high ZT value of 0.92 at 300 K is achieved. According to the results, a sintering temperature of 673 K is preferable for consolidation of fine (<$20{\mu}m$) powders.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.64-76
• /
• 1997

This paper deals with development of brackets by using aluminum alloy sheets which is indispensable for weight reduction of autobody. The press formability of aluminum alloy sheet is estimated by means of tensile test, V bending test, sample manufacturing test and photograph of microstructure. The results show that the elongation, strength, work hardening exponent, plastic anisotropy coefficient of Al 6***series are better than those of Al 5***series, but for general press formability, Al 5***series are better than Al 6***series due to lower yield strength. Since most of mechanical properties of aluminum sheet are generally inferior to those of cold-rolled steel sheet, shape fixability and press formability of aluminum sheet are very poor. For making components of autobody by use of die for steel sheet application, it is essential that die should be nodified for least bending and stretching. With the modified die for aluminum, it could be possible to make brackets, the component of autobody. Microstructure of Al 5***series has fine grain and small the 2nd phase and that of Al 6***series has relatively coarse grain. Therefore, it seems that fine grain and small the 2nd phase of Al 5***series is one of the factor of lower yield strength, resistance to stamping work, formation of Luder's line.

• Journal of Powder Materials
• /
• v.23 no.6
• /
• pp.447-452
• /
• 2016

Neodymium-iron-boron (Nd-Fe-B) sintered magnets have excellent magnetic properties such as the remanence, coercive force, and the maximum energy product compared to other hard magnetic materials. The coercive force of Nd-Fe-B sintered magnets is improved by the addition of heavy rare earth elements such as dysprosium and terbium instead of neodymium. Then, the magnetocrystalline anisotropy of Nd-Fe-B sintered magnets increases. However, additional elements have increased the production cost of Nd-Fe-B sintered magnets. Hence, a study on the control of the microstructure of Nd-Fe-B magnets is being conducted. As the coercive force of magnets improves, the grain size of the $Nd_2Fe_{14}B$ grain is close to 300 nm because they are nucleation-type magnets. In this study, fine particles of Nd-Fe-B are prepared with various grinding energies in the pulverization process used for preparing sintered magnets, and the microstructure and magnetic properties of the magnets are investigated.

• Journal of Powder Materials
• /
• v.3 no.3
• /
• pp.181-187
• /
• 1996

Cobalt and VC powders were ball milled with M2 grade high speed steel powders under various ball to powder ratios. The powders milled under higher ball to powder ratio become finer, more irregular and have a broader size distribution, and thus possess a lower compressibility and a better sinterability regarding densification. Increasing the ball to powder ratio lowered the sintering temperature to obtain the density level necessary to isolate all the pores. Lowering the sintering temperature is very critical to maintain fine microstructure since grain and carbide coarsening are accelerated by higher sintering temperature due to more liquid phase formation. The powders obtained by ball milling at 20 to 1 ratio has the lowest compressibility but has the best sinterability, almost compatible to unmilled pure M2 powders. A sintered body over 97% theoretical density with fine microstructures having average grain size of ~10 microns was obtained from the powder by sintering at 1260 $^{\circ}C$ for 1 hour in vacuum. XRD results indicate that two types of carbides are mainly present in the sintered structure, MC and $M_{6}C$ type. The MC type carbides are more or less round shaped and mainly located at the grain boundaries whereas the $M_{6}C$ type are angular shaped and mainly located inside the grains.