• 산업기술연구
• /
• 제7권
• /
• pp.49-58
• /
• 1987

To investigate the effect of the Retrogression and Reaging (RRA) treatment on the strength and the stress corrosion cracking in AA 7039 the measurement of hardness, tensile properties and the time to failure in a constant rate method were measured. Transmission electron microscope was used to examine the microstructural changes within graln and grain boundary. The results show that the RRA treatment of the T6 condition results in a significant increase in the time to failure without sacrifying the original T6 strength. It is believed that high density and even distribution of precipitates in RRA condition were observed within grain so that the RRA condition could have similar strength to the T6 condition. The presence of fine dispersion of semicohernt ${\eta}^{\prime}$ transition phase is also believed to contribute to that effect. Examination of the grain boundary microstructure shows that the RRA treatments increases significantly the average size of the grain boundary preciptates. It is suggested that the benificial effect of the RRA treatment on the susceptibility to SCC be due to the increase in the size of grain boundary precipitates obtained during the retrogression treatment.

• 전기화학회지
• /
• 제11권4호
• /
• pp.227-241
• /
• 2008

This article involves a unified treatment of equilibrium thermodynamics of the chemical reaction coupled with other interfacial (phase boundary) reactions. The modified (restrictive) chemical potential ${\mu}_k^+$, such as electrochemical potential, hydrostatic-chemical (mechanochemical) potential (exceptionally in the presence of the pressure difference) and surface-chemical potential, was first introduced under the isothermal and isobaric conditions. This article then enlightened the equilibrium conditions in case where the release of chemical energy is counterbalanced by the supply of electrical energy, by the supply of hydrostatic work (exceptionally in the presence of ${\Delta}p$), and finally by the release of surface energy, respectively, at constant temperature T and pressure p in terms of the modified chemical potential ${\mu}_k^+$. Finally, this paper focussed on the difference between chemical and electrochemical equilibria based upon the fundamentals of the isothermal and isobaric equilibrium conditions described above.

• 한국주조공학회지
• /
• 제15권6호
• /
• pp.566-573
• /
• 1995

In this study, the microstructural characteristics such as primary silicon, eutectic silicon, $SiC_p$ dispersion behavior, compound amount and Si solubility in $Al/SiC_p$ composite fabricated by the squeeze casting under various conditions were investigated systematically. As applied pressure(MPa) increases, cooling rate and compound amount are increased. In gravity casting, the cooling rate of hypereutectic composite is slower than of hypoeutectic composite by exothermic reaction of primary Si crystallization. But the cooling rate of hypereutectic composite is faster than that of hypoeutectic composite fabricated by same applied pressure, because amount of primary Si crystallization in hypereutectic composite was decreased, on the contrary, primary ${\alpha}-Al$ in hypoeutetic composite was increased due to increase of Si solubility in matrix by applied pressure. The crystalized primary silicon in hypereutectic composite fabricated by squeeze casting become more fine than that in non-pressure casting This is because mush zone became narrow due to increase of Si content of eutectic composition by pressure and time for growth of primary silicon got shorter according to applied pressure. It is turned out that eutectic temperature and liquidus are decreased by the increasing of squeeze pressure in all the composite due to thermal unstability of matrix owing to increasing of Si solubility in matrix by the increasing of applied pressure, as indicated in thermal anaiysis(DSC) results.

• 암석학회지
• /
• 제22권4호
• /
• pp.273-289
• /
• 2013

강하화산재는 농업과 기반시설에 다양한 형태의 피해를 발생시킬 수 있는 악명 높은 재해이며, 특별히 항공과 인체 건강에 가장 유해하다. 본 연구는 백두산 화산으로부터 폭발적 분화에 의하여 화산재가 확산되고 퇴적되는 것을 모델링하기 위한 목적으로 개념적인 모델 설계를 논의하고자 한다. 이는 모델의 가정과 경계 조건에 대한 토의와 더불어 개념적인 모델의 상세 다이어그램, 가능한 입력 파라미터, 단위, 방정식에 대한 논의를 포함한다. 모델에 포함되어 있는 두 가지 주요 과정은 화산재의 확산과 퇴적이며, 만약 모델이 설계되면 모델을 실행시켜 얻을 수 있는 것은 분연주에 포함된 미세 화산재의 총량, 화산재의 이동 거리, 지표면에 침적되는 화산재 두께 등이다.

• 한국수소및신에너지학회논문집
• /
• 제22권4호
• /
• pp.415-423
• /
• 2011

HI decomposition step certainly demand catalytic reaction for efficient production of hydrogen in SI process. Platinum catalyst can apply to HI decomposition reaction as well as hydrogenation or dehydrogenation. Generally, noble metal is used as catalyst which is loaded form for getting high dispersion and wide active area. In this study, Pt was loaded onto zirconia, ceria, alumina, and silica by impregnation method. HI decomposition reaction was carried out under the condition of $450^{\circ}C$, 1atm, and $167.76h^{-1}$ (WHSV) in a fixed bed reactor for measuring catalytic activity. And property of a catalyst was observed by BET, TEM, XRD and chemisoption analysis. On the basis of experimental results, we discussed about conversion of HI according to physical properties of the loaded Pt catalyst onto each support.

• 한국재료학회지
• /
• 제23권3호
• /
• pp.199-205
• /
• 2013

The mechanical properties and microstructures of aluminum-matrix composites fabricated by the dispersion of fine alumina particles less than $20{\mu}m$ in size into 6061 aluminum alloys are investigated in this study. In the as-quenched state, the yield stress of the composite is 40~85 MPa higher than that of the 6061 alloy. This difference is attributed to the high density of dislocations within the matrix introduced due to the difference in the thermal expansion coefficients between the matrix and the reinforcement. The difference in the yield stress between the composite and the 6061 alloy decreases with the aging time and the age-hardening curves of both materials show a similar trend. At room temperature, the strain-hardening rate of the composite is higher than that of the 6061 alloy, most likely because the distribution of reinforcements enhances the dislocation density during deformation. Both the yield stress and the strain-hardening rate of the T6-treated composite decrease as the testing temperature increases, and the rate of decrease is faster in the composite than in the 6061 alloy. Under creep conditions, the stress exponents of the T6-treated composite vary from 8.3 at 473 K to 4.8 at 623 K. These exponents are larger than those of the 6061 matrix alloy.

• 한국재료학회지
• /
• 제28권9호
• /
• pp.495-498
• /
• 2018

Intermetallic compound matrix composites have been expected to be established as high temperature structural components. $Ni_3Al$ is a representative intermetallic alloy, which has excellent ductility even at room temperature by adding certain alloying elements. $Ni_3Al$ matrix composites with aluminum oxide particles, which are formed by the in-situ reaction between the alloy and aluminum borate whiskers, are fabricated by a powder metallurgical method. The addition of aluminum borate whiskers disperses the synthetic aluminum oxide particles during sintering and dramatically increases the strength of the composite. The uniform dispersion of reaction synthesized aluminum oxide particles and the uniform solution of boron in the matrix seem to play an important role in the improvement in strength. There is a dramatic increase in strength with the addition of the whisker, and the maximum value is obtained at a 10 vol% addition of whisker. The $Ni_3Al$ composite with 10 vol% aluminum oxide particles $0.3{\mu}m$ in size and with 0.1 wt% boron powder fabricated by the conventional powder metallurgical process does not have such high strength because of inhomogeneous distribution of aluminum oxide particles and of boron. The tensile strength of the $Ni_3Al$ with a 10 vol% aluminum borate whisker reaches more than twice the value, 930 MPa, of the parent alloy. No third phase is observed between the aluminum oxide and the matrix.

• 한국세라믹학회지
• /
• 제43권9호
• /
• pp.519-526
• /
• 2006

A full-factorial design of experiments with three input factors and two levels for each factor including center points was utilized for the preparation and characterization of twelve types of $BaTiO_3$ slips for tape casting. Ceramic powders with different particle sizes, different milling methods such as high energy milling and conventional ball milling, and two types of dispersant with different polymeric species were chosen as input factors in order to investigate their effects on slip and on green tape properties. Tape casting, a small rectangular-shaped K-square preparation, characterization and quantitative data analysis using statistical software were followed. Ceramic powder was the most significant among three input factors for the output responses of slip viscosity and green tape density, showing more favorable results with large particles than with very fine ones. In addition, high energy milling for only 30 min was more efficient than 24h of conventional ball milling in terms of powder dispersion and milling. The optimum condition based on the experimental results was a slip exposed to high energy milling with large ceramic particles along with a methylethyl acetate dispersant.

• Corrosion Science and Technology
• /
• 제7권4호
• /
• pp.201-207
• /
• 2008

$CO_2$ corrosion product scales formed on 13 Cr tubing steel in autoclave and in the simulated corrosion environment of oil field are investigated in the paper. The surface and cross-section profiles of the scales were observed by scanning electron microscopy (SEM), the chemical compositions of the scales were analyzed using energy dispersion analyzer of X-ray (EDAX), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) to confirm the corrosion mechanism of the 13 Cr steel in the simulated $CO_2$ corrosion environment. The results show that the corrosion scales are formed by the way of fashion corrosion, consist mainly of four elements, i.e. Fe, Cr, C and O, and with a double-layer structure, in which the surface layer is constituted of bulky and incompact crystals of $FeCO_3$, and the inner layer is composed of compact fine $FeCO_3$ crystals and amorphous $Cr(OH)_3$. Because of the characteristics of compactness and ionic permeating selectivity of the inner layer of the corrosion product scales, 13 Cr steel is more resistant in $CO_2$ corrosion environment.

• Nuclear Engineering and Technology
• /
• 제40권2호
• /
• pp.99-106
• /
• 2008

Through mechanical alloying, hot isostatic pressing and hot rolling, a 9%Cr Fe-based oxide dispersion-strengthened alloy sample was fabricated. The tensile strength of the alloy is significantly improved when the microstructure is modified during the post-consolidation process. The alloy samples were strengthened as the cooling rates increased, though the elongation was somewhat reduced. With a cooling rate of $800^{\circ}C/s$ after normalization at $1150^{\circ}C$, the alloy sample showed a tensile strength of 1450 MPa, which is about twice that of the hot rolled sample; however, at $600^{\circ}C$ the tensile strength dramatically decreased to 620 MPa. Optical microscope and transmission electron microscope were used to investigate the microstructural changes of the specimens. The resultant strengthening of the alloy sample could be mainly attributed to the interstitially dissolved nitrogen, the fraction of the tempered martensite, the fine grain and the presence of a smaller precipitate. The decrease in the tensile strength was mainly caused by the precipitation of vanadium-rich nitride.