• Journal of Korean Society for Atmospheric Environment
• /
• v.29 no.5
• /
• pp.656-667
• /
• 2013

The non-exhaust coarse, fine, and ultrafine particles were characterized by on-road driving measurements using a mobile sampling system. The on-road driving measurements under constant speed driving revealed that mass concentrations of roadway particles (RWPs) were distributed mainly in a size range of 2~3 ${\mu}m$ and slightly increased with increasing vehicle speed. Under braking conditions, the mode diameters of the particles were generally similar with those obtained under constant speed conditions. However, the PM concentrations emitted during braking condition were significantly higher than those produced under normal driving conditions. Higher number concentrations of ultrafine particles smaller than 70 nm were observed during braking conditions, and the number concentration of particles sampled 90 mm above the pavement was 6 times higher than that obtained 40 mm above the pavement. Under cornering conditions, the number concentrations of RWPs sampled 40 mm above the pavement surface were higher than those sampled 90 mm above the pavement. This might be explained that a nucleation burst of a lot of vapor evaporated from the interaction between the tire and the road pavement under braking conditions continuously occurred by cooling during the transport to the sampling height 90 mm, while, for the case of cornering situations, the ultrafine particle formation was completed before the transport to the sampling height of 40 mm.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.3
• /
• pp.263-273
• /
• 2003

P $M_{2.5}$ fine particles have been collected at the Cosan measurement station in Jeju Island, and the major water-soluble components have been analyzed in order to Investigate the aerosol compositions and pollution characteristics. The mean concentrations of the components were in the order of S $O_4$$^{2-}$> N $H_4$$^{+}$> N $O_3$$^{[-10]}$ > N $a^{+}$> $K^{+}$>C $l^{[-10]}$ >C $a^2$$^{+}$>M $g^2$$^{+}$. The major components were S $O_4$$^{2-}$, N $H_4$$^{+}$ and N $O_3$$^{[-10]}$ , whose compositions were 58％, 18％ and 10％ of the total ions, respectively. Most of the components showed higher concentrations in spring season, and especially $Ca^2$$^{+}$, N $O_3$$^{[-10]}$ and S $O_4$$^{2-}$ concentrations were increased 2.8, 1.9 and 1.2 times higher than the annual mean concentrations. The most parts of S $O_4$$^{2-}$ and N $H_4$$^{+}$ were distributed in fine particles below 2.1 ${\mu}{\textrm}{m}$ size, but the $Ca^2$$^{+}$, N $a^{+}$ and C $l^{[-10]}$ showed relatively higher concentrations in coarse particles. Based on the factor analysis, the P $M_{2.5}$ fine particles were considered to be largely influenced by anthropogenic sources, and followed by sea salt and soil sources. In the variations of concentrations as a function of wind direction, most components have shown higher concentrations notably as the northwesterly prevails.thwesterly prevails.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.04a
• /
• pp.239-242
• /
• 2004

Pilot-scale soil washing facility was developed and operation condition was determined in order to remediate a soil contaminated with As, Ni and Zn. Soil washing facility is composed of soil particle separation, soil washing and wastewater treatment process. Both oxyanionic As and cationic Ni and Zn were effciently removed using HCl rather 0than H$_2$SO$_4$ and H$_2$PO$_4$. This is why oxyanion and cation metals can be extracted simultaneously from the contaminated soil in acidic solution. Further, the contaminated soils include calcite and then demand much acidity, that is consumption of acid solution. Fine particles are enriched with contaminants, and coarse particles are removed effectively rather than fine particles. As, Ni and Zn are strongly associated with minerals, and then the residence time should be increased for a reaction with washing solution.

• Asian Journal of Turfgrass Science
• /
• v.10 no.1
• /
• pp.49-59
• /
• 1996

This report is researched on the cause and mechanism of soil erosion in comparison among Kwangnung, Mt. Kaya, Mt. Chili, and Mt. Soorak by physical and chemical analyses of their for- est soils. Clay, silt, and fine sand of Mt. Soorak are far less than those of Mt. Chili, Mt. Kaya, and Kwangnung area while coarse sand is very high level. The clay ratio of soil at Mt. Soorak is the most high level in comparison with that of other area. Denudation at Mt. Soorak, therefore, is cause of erosion by the result of transportation of soil particles. The eroding velocity increase for larger particle size and stronger cohesion between soil particles. Very fine sand, silt, and clay can be present in suspension near the bottom and the size of the particles in suspension depends upon the velocity of the current near the bottom and the roughness of the bottom. Key words: Theoretical analyses, Soil erosion and conservation, Forest soils.

• Analytical Science and Technology
• /
• v.30 no.4
• /
• pp.182-193
• /
• 2017

In order to examine the variation characteristics of chemical compositions in relation to the inflow pathways of Asian dust, $PM_{10}$ and $PM_{2.5}$ aerosols were collected at Gosan site of Jeju Island during the Asian dust days between 2010 and 2015, and their chemical compositions were analyzed. The mean mass concentrations of $PM_{10}$ and $PM_{2.5}$ during Asian dust days were $130.0{\pm}90.2$ and $38.2{\pm}24.7{\mu}g/m^3$, respectively. The composition ratios of major secondary pollutants ($nss-SO_4{^{2-}}$, $NH_4{^+}$, $NO_3{^-}$) were high as 53.7 % for $PM_{10-2.5}$ and 90.6 % for $PM_{2.5}$. When the Asian dusts had been transported to the Korean Peninsula via Loess Plateau of central China, the concentrations of $nss-Ca^{2+}$, $NH_4{^+}$, $nss-SO_4{^{2-}}$, and $NO_3{^-}$ increased more noticeably. Whereas in case when the inflow pathways of Asian dust had been through the Bohai bay, the concentrations of the crustal species such as Al, Fe, and Ca were relatively high in coarse particles. The atmospheric aerosols were acidified largely by sulfuric and nitric acids. They were neutralized mainly by calcium carbonate in coarse particle mode passed through Manchuria area, but by ammonia in fine particle mode passed through Loess plateau and Bohai bay. Ammonium salts are assumed to exist as ammonium sulfate and ammonium nitrate in coarse particles, but mostly as ammonium sulfate in fine particles.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.4
• /
• pp.106-113
• /
• 2002

This research was performed to investigate the effect of moulding conditions on properties of the table top for student desk manufactured by wood waste materials. The table top manufactured using the mat mixed properly with fine particles and coarse particles generally showed better physical properties than those manufactured using either fine particles or coarse particles did/ Especially, highest performance for overlaying was observed when fine particles were used for face layer and coarse particles were used for core layer. The internal bond (IB) strength, the bending strength and thickness swelling increased with the increase of density. Most of physical properties were improved with the increase of hot pressing temperature. The best physical properties were found at 190℃ when the first hot pressing and the second hot pressing times were two minutes. However, the effect of the second hot pressing time of two minutes on the physical properties was not markedly different from that of one minute. This result suggests that the second hot pressing time of one minute is enough to increase the productivity in manufacturing the table top with the least decrease of the physical properties.

• Geomechanics and Engineering
• /
• v.13 no.6
• /
• pp.947-961
• /
• 2017

An innovative spiral variable-section capillary model is established for piping critical hydraulic gradient of cohesion-less soils causing water/mud inrush in tunnels. The relationship between the actual winding seepage channel and grain-size distribution, porosity, and permeability is established in the model. Soils are classified into coarse particles and fine particles according to the grain-size distribution. The piping critical hydraulic gradient is obtained by analyzing starting modes of fine particles and solving corresponding moment equilibrium equations. Gravities, drag forces, uplift forces and frictions are analyzed in moment equilibrium equations. The influence of drag force and uplift force on incipient motion is generally expounded based on the mechanical analysis. Two cases are studied with the innovative capillary model. The critical hydraulic gradient of each kind of sandy gravels with a bimodal grain-size-distribution is obtained in case one, and results have a good agreement with previous experimental observations. The relationships between the content of fine particles and the critical hydraulic gradient of seepage failure are analyzed in case two, and the changing tendency of the critical hydraulic gradient is accordant with results of experiments.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.2
• /
• pp.58-67
• /
• 2001

MOW (Mixed Office Waste) mainly consisted of photocopied paper is being recycled to produce tissue or fine paper products. Toner particles that are fused and set on paper surface in photocopying process turns into large and plate-shaped particles after repulping which prevents them to be removed effectively in flotation deinking. The immediate purpose of this study is to find the effective deinking technology that increases the recycling potential of photocopied papers for manufacturing tissue and fine paper products. In this study the effects of pulping temperature and the type of hydrophobic groups of nonionic surfactants on the deinking efficiency of photocopied paper has been investigated. Particle size distribution of the toner particles after pulping and flotation, brightness, yield and ash removal were investigated. The size of toner particles after pulping increased as the pulping temperature was increased. When pulping at the low temperature finer toner particles were generated, however, greater amount of toner particles was found to attach to the fiber. When the pulping temperature was greater than Tg of the toner, the amount of coarse hairy particles increased. When nonionic surfactants with a double bond in hydrophobic groups were used, toner removal efficiency, brightness and ash removal were increased. As the addition level of surfactant was increased, yield decreased rather sharply without improving brightness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.237-241
• /
• 2000

The effects of Si addition on the precipitation processes of in Al-Cu-Si alloy films were studied by the transmission electron microscopy. Deposition of an Al-1.5Cu-1.5Si (wt. %) film at $305^{\circ}C$ resulted in formation of fine, uniformly distributed spherical $\theta$-phase particles due to the precipitation of the $\theta$ and Si phase particles during deposition. For deposition at $435^{\circ}C$, fine $\theta$-phase particles precipitated during wafer cooldown, while coarse Si nodules formed at the sublayer interface during deposition. The film susceptibility to corrosion is discussed in relation to the film microstructure and deposition temperature.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.217-221
• /
• 2002

In the coarse grain HAZ adjacent to the fusion line, most of the TiN particles in conventional Ti added steel are dissolved and austenite grain growth is easily occupied during welding process. To avoid this difficulty, thermal stability of TiN particle is improved by increasing the nitrogen content in steel. In this study, the effect of high nitrogen TiN particle on preventing austenite grain growth in HAZ was investigated. Increased thermal stability of TiN particle is helpful for preventing the austenite grain growth by pinning effect. High nitrogen TiN particle in simulated HAZ were not dissolved even at high temperature such as 1400 C and prevented the austenite grain growth in simulated HAZ. Owing to small austenite grain size in HAZ the width of coarse grain HAZ in high nitrogen TiN steel was decreased to 1/10 of conventional TiN steel. Even high heat input welding, the microstructure of coarse grain HAZ consisted of fine polygonal ferrite and pearlite and toughness of coarse grain HAZ was significantly improved.