• KEPCO Journal on Electric Power and Energy
• /
• v.1 no.1
• /
• pp.151-156
• /
• 2015

In order to improve the properties of high-temperature superconducting wire for superconducting cable system, we optimized the electro-polishing (EP), ion-beam assisted deposition (IBAD), superconducting (SC) layer, and baking (heat) treatment. The buffer layer was deposited on electro-polished substrate with RMS roughness ($R_{RMS}$) less than 5 nm. The IBAD process was carried out at $V_{beam}$: 1100 V and $V_{accel}$: 850 V that resulted in highly crystalline film of $LaMnO_3$. Chemical composition of SC layer is key to higher critical current, and we found that composition can be determined by surface color of SC layer. We adopt a proprietary contorl system based on RGB analysis of the surface and achieved critical current of 150 A/4 mm-width. The proposed baking treatment resulted in decreasing of about 10% of fraction defects.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1053-1056
• /
• 2004

Chunghwa Picture Tubes, LTD. (CPT) has developed a Novel TFT-LCD Driving Techniquel. This new technique is developed in combination with other state-of-the-art image processing solutions such as image compression / decompression, motion detection, and noise reduction. By applying the Novel Driving Technique to the high resolution TFT-LCD, it was found that the response time can be effectively reduced with a lower overall system cost by smaller frame memory requirement, lower EMI by less memory band-width. Likewise, higher display quality can also be achieved in that the unexpected noises generated by over-drive can be eliminated. The Novel TFT-LCD Driving Technique has been successfully implemented to the 30 inch WXGA (1280${\times}$768) resolution TFT LCD commercial TV module. It was found that the quality of moving picture was better improved compared with that of the conventional fast response driving method.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.2
• /
• pp.132-138
• /
• 2000

The effect of fluid flow on corrosion and erosion-corrosion of metal is a well-recognized phenomenon in pipelines and machinery equipment, and so on. Not only are fluid hydrodynamics important, but also the corrosiveness of the process or production stream affects the corrosion system. Recent research demonstrates that it is possible to erosion-corrosion(E/C) phenomena in terms of hydrodynamics, electrochemical corrosion kinetics and film growth/removal phenomena. Stress corrosion cracking behavior under cavitation erosion-corrosion of mild steel(SS41) was investigated of base metal and weldment under loaded stress. Main result obtained are as follows : 1) The cavitation erosion sensitivity of base metal affected weight loss is more susceptive than heat affected zone, 2) The corrosion sensitivity affected weight loss of welding heat cycle is less susceptive on stress corrosion under cavitation erosion-corrosion than stress corrosion.

• Journal of the Korean Vacuum Society
• /
• v.2 no.4
• /
• pp.474-479
• /
• 1993

Submicron contact hole filling with aluminum alloys has been achieved with a multistep metallization method, which utilizes a metal " flow" or self-diffusion process at elevated temperatures after the metal was sputter-deposited. A multi-chamber, modular sputtering system was employed to deposit aluminum alloys and subsequently to anneal the deposited metal films under vacuum at high temperatures. The film were deposited on 200 mm wafers with planar, dc magnetron sputtering sources without anysubstrate bias. The basic process steps studied for the multistep metallization include an initial layer deposition at low temperatures less than $100^{\circ}C$, and an annealin gstep at elevated temperatures, between 450 and $550^{\circ}C$. The degree of planarization or step coverage was dependent strongly upon the temperature and time of the flow step and complete filling of the submicron contacts with aluminum alloys was achieved. Responsible mechanisms for the enhancement in step coverge and factros determining uniform and reproducible flow of aluminum alloys during the high temperauture step are discussed.discussed.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.4
• /
• pp.173-178
• /
• 2015

In lieu of the excellent radio frequency (RF) performance of microelectromechanical system ( MEMS) switches, these micro switches need higher actuation voltage for their operation. This requirement is secondary to concerns over the swtiches’ reliability. This paper reports high reliability operation of RF MEMS switches with low voltage requirements. The proposed switch is optimised to perform in the Q-band, which results in actuation voltage of just 16.4 V. The mechanical stress gradient in the thin micro membrane is computed by simulating von Mises stress in a multi-physics environment that results in 90.4 MPa stress. The computed spring constant for the membrane is 3.02 N/m. The switch results in excellent RF performance with simulated isolation of above 38 dB, insertion loss of less than 0.35 dB and return loss of above 30 dB in the Q-band.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.584-587
• /
• 2006

An energy generating greenhouse based on fluoropolymer envelope and fresnel lens is proposed. The outstanding properties of the fluoropolymer films make them very suitable for large scale solar applications. Extremely high optical transmission over the whole solar spectrum, combined with mechanical strength, and durability allows us to design a highly optimized greenhouses for both plant growing and energy generation. Systems such as photovoltaic triple junction cells are especially attractive since they have up to 35% efficiency with much less cell material when the sun beam is focused with concentrators such as fresnel lenses. Cooling such devices will enhance the efficiency and provide useful thermal energy that could be further utilized for various applications depending on the local demands. This article introduces the basic ideas and principles of the energy generating greenhouses as a first step towards the actual deployment of such systems under Korean environment.

• Journal of Bio-Environment Control
• /
• v.22 no.2
• /
• pp.175-181
• /
• 2013

These studies were identified the effect of four types of non-perforated breathable (NPB) packing film and three sizes on storage ability of fresh-cut for ready to eat packaging at $5^{\circ}C$ for 25 days and $10^{\circ}C$ for 15 days storage in Salicornia herbacea. The fresh weight loss was less than 2% in every films at $5^{\circ}C$ condition after 25 days storage, and the $10^{\circ}C$ also had same result on 15 days storage except 100,000 cc NPB film. Compare with storage after 15 days, storage condition at $5^{\circ}C$ had shown better result under the 1% fresh weight loss rate. The 5,000 cc and $5^{\circ}C$ condition had been shown the characteristics of MA packaging in carbon dioxide and oxygen concentrations. The ethylene concentration in vacuum film was higher 10 to 100 times than in NPB film treatments during storage. But ethylene concentration was not statistically significant differences among size treatments. Every conditions had been measured the anti-oxidant activity by DPPH method after storage at $5^{\circ}C$ for 25 days and $10^{\circ}C$ for 15 days. S. herbacea at $5^{\circ}C$ had been more than twice of activity compare with that at $10^{\circ}C$. 100,000 cc NPB film had been higher contents of anti-oxidant activity at $5^{\circ}C$ and $10^{\circ}C$. As the fresh-cut sizes, 3 cm and 5 cm sizes had changed depending on film types but 10 cm were not effected by the film types in the DPPH activity. When panel test had been tried to measure the visual quality and off-flavor after storage, $5^{\circ}C$ with a filme of 5,000 cc treatment had established higher value than other treated conditions. As these results, it's may be suggested that the $5^{\circ}C$ with 5,000 cc non-perforated breathable film for MA storage in Salicornia herbacea at fresh cut distribution system. Fresh cut size 10 cm with 100,000 cc NPB film also had the good quality for 15 dyas storage at $10^{\circ}C$, and this result can be applied for short term distribution system in Korea.

• Korean Journal of Weed Science
• /
• v.32 no.2
• /
• pp.107-114
• /
• 2012

This study was conducted to evaluate the weed suppressing effects of different cropping system including hairy vetch (Vicia villosa) and rye (Secale cereale) cover crops, polyethylene plastic film, and transplanting film mulching in direct sowing and transplanted sorghum field in 2011. Crop growth and development and weed occurrences in the fields were examined to know the efficiency of proposed cropping system. In polyethylene film mulching treatment, heading date of sorghum was earlier by 3 days than control, on the other hands, rye cover crop mulching delayed heading date by 11 days. Besides the effect of cover crop on the heading of sorghum, the residues changed growth characteristics. Plant height of sorghum was increased by 27.3% at hairy vetch treatment although it was reduced by 47.5% in the rye cover crop treatment. Hairy vetch treatment showed beneficial effects on sorghum growth reduced the occurrences of grasses and broadleaf weeds to 84% and 96%, respectively, as compared to control in sorghum fields. While rye cover crop treatment showed poor sorghum growth reduced less strongly grasses and broadleaf weeds by 35% and 71%, respectively. At harvest, yield of sorghum was greater in order of hairy vetch cover crop > polyethylene film mulching > rye cover crop ${\fallingdotseq}$ control in both transplanted and direct sown fields.

• Korean Journal of Materials Research
• /
• v.2 no.1
• /
• pp.58-64
• /
• 1992

TCR modifying oxides which have negative TCR were added to the $\textrm{RuO}_2$ thick film resistors and how they affect the TCR and resistivity of the systems were investigated. Two types of resistor systems whose ratio of $\textrm{RuO}_2$ to glass were 20/80 and 12/88 were used as standard resistors. It was observed that the modifiers did not always lower the TCR of the resistors and the direction of the TCR change were different from system to system. It was confirmed, however, that the feasibility of optimization of TCR of the resistors. When more than two TCR modifiers were added simultaneously there was no interaction between them. The resultant TCR of the resistor wart just sum of the effects from individual modifier. It was found to be desirable that the amount of addition of the TCR modifiers should be less than 2 to 3 percent.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.253-256
• /
• 2009

In the micro turbojet engine less than 350kw power class, it is not easy to find out the good atomization fuel injector with good spray quality. However conceptually, rotating fuel injection system can give high atomization quality by only the centrifugal force of a high speed rotating shaft of the engine without high-pressure fuel pump. With this motivation, we manufactured very small rotating fuel injector of 40 mm diameter and performed under a variety of injection orifices. We measured droplet size, velocity and spray distribution by the PDPA(Phase Doppler Particle Analyzer) system. Also spray was visualized by using high speed camera. From the test results, we could understand that the length of liquid column from the injection orifice is mainly controlled by the rotational speeds. Furthermore, droplet size(SMD) is decreased with the rotational speeds and is influenced by the diameter of the injection orifice and liquid film thickness.