• Applied Chemistry for Engineering
• /
• v.8 no.1
• /
• pp.29-38
• /
• 1997

In the w/o concentrated emulsion, the volume fraction of the dispersed is greater than 0.74 and the hydrophilic liquid is dispersed in the hydrophobic liquid of the continuous phase. The emulsion has the same appearance and behaviour as a gel. The polarity of the hydrophilic liquids and hydrophobic liquids, the pH and the ionic strength of the hydrophilic liquid are found to be important factors in the stability at the polymerization temperature such as $50^{\circ}C$. The lower the polarity of the hydrophobic liquid and the higher the polarity of the hydrophilic liquid, the more stable the emulsion. Electron microscopy studies of the hydrophilic-hydrophobic polymer composites show that the particles of polyacrylamide, the dispersed phase, are separated by he network of the thin film of polystyrene, the continuous phase. This hydrophilic-hydrophobic polymer composites show higher permselectivity to water in the mixture of water-ethanol. The pervaporation experiment shows that the selectivity of the membrane ranges between 4-40 and increases with increasing enthanol concentration in the feed. The rate of permeation decreases with increasing ethanol concentration in the feed.

• Journal of the Korean Solar Energy Society
• /
• v.37 no.2
• /
• pp.47-57
• /
• 2017

CIGS thin film solar cells are technically suitable for BIPV applications than regularly used crystalline silicon solar cells. Particularly, CIGS PV has lower temperature coefficient than crystalline silicon PV, thus decrease in power generation is lowered in CIGS PV. Moreover, CIGS PV can decrease shading loss when applied to the BIPV system, and the total annual power generation is higher than crystalline silicon. However, there are few studies on the installation factors affecting the performance of BIPV system with CIGS module. In this study, BIPV curtain wall unit with CIGS PV module was designed. To prevent increase of temperature of CIGS PV module by solar radiation, ventilation was considered at the backside of the unit. The thermal specification and electrical performance of CIGS PV of the ventilated unit was analyzed experimentally. Non-ventilated unit was also investigated and compared with ventilated unit. The results showed that the average CIGS temperature of the ventilated curtain wall unit was $6.8^{\circ}C$ lower than non-ventilated type and the efficiency and power generation performance of ventilated CIGS PV on average was, respectively, about 6% and 5.8% higher than the non-ventilated type.

• Journal of Sensor Science and Technology
• /
• v.29 no.4
• /
• pp.266-269
• /
• 2020

In this study, we investigated the effect of a sulfur passivation (S-passivation) process step on the electrical properties of surface-channel In_0.7Ga_0.3As quantum-well (QW) metal-oxide-semiconductor field-effect transistors (MOSFETs) with S/D regrowth contacts. We fabricated long-channel In_0.7Ga_0.3As QW MOSFETs with and without (NH₄)₂S treatment and then deposited 1/4 nm of Al₂O₃/HfO₂ through atomic layer deposition. The devices with S-passivation exhibited lower values of subthreshold swing (74 mV/decade) and drain-induced barrier lowering (19 mV/V) than the devices without S-passivation. A conductance method was applied, and a low value of interface trap density D_it (2.83×10¹² cm^-2eV^-1) was obtained for the devices with S-passivation. Based on these results, interface traps between InGaAs and high-κ are other defect sources that need to be considered in future studies to improve III-V microsensor sensing platforms.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.275-277
• /
• 2007

유리를 기판으로 하는 superstrate pin 비정질 태양전지에서 전면투명전도막(TCO)과 p-layer의 계면이 태양전지의 효율을 내는데 가장 큰 기여를 한다. 전면투명전도막(TCO)으로 현재 일반적으로 사용되는 ZnO:Al는 $SnO_2:F$ 보다 전기,광학적으로 우수하고, 안개율(Haze)높으며, 수소 플라즈마에서의 안정성이 높은 특정을 갖고 있다. 그래서 박막 태양전지 특성향상에 매우 유리하나, 태양전지로 제조했을 때, $SnO_2:F$보다 충진율(Fill factor:F.F)과 V_{\infty}$ 가 감소한다는 단점을 가지고 있다. 본 실험실에서는 $SnO_2:F$의 F.F가 72%이 나온 반면 ZnO:Al의 F.F은 68%에 그쳤다. 이들 원인을 분석하기 위해 TCO/p-layer의 전기적 특성을 알아 본 결과, $SnO_2:F$보다 ZnO:Al의 직렬저항이 높게 측정되었다. 이러한 결과를 바탕으로 p-layer 에 R={$H_2/SiH_4$}=25로 변화, p ${\mu$}c$-Si:H/p a-SiC:H 로 p-layer 이중 증착, p-layer의 boron doping 농도를 증가시키는 실험을 하였다. 직렬저항이 가장 낮았던 p ${\mu$}c$-Si:H/p a-SiC:H 로 p-layer 이중 증착에서 Voc는 0.95V F.F는 70% 이상이 나왔다. 이들 각 p층의 $E_a$(Activation Energy)를 구해본 결과, ${\mu$}c$-Si:H의 Ea 가 가장 낮은 것을 관찰 할 수 있었다.

• Biomolecules & Therapeutics
• /
• v.19 no.2
• /
• pp.231-236
• /
• 2011

The aim of this study was to investigate the effect of charge carrier lipid on the skin penetration, retention, and hair growth of topically applied finasteride-containing liposomes. Finasteride-containing liposomes were prepared by traditional thin film hydration method using Phospholipon$^{(R)}$ 85 G and cholesterol with or without charge carrier lipid (1,2 dimyristoyl-sn-glycero-3-phosphate or 1,2-dioleoyl-trimethylammonium-propane for anionic and cationic charge, respectively). Freshly prepared finasteride-containing liposome suspension was applied on the hairless mouse skin, and skin penetration and retention were measured using Keshary-Chien diffusion cell. Non-liposomal formulation (ethanol 10% solution containing 0.5 mg/ml of FNS) was also used as a control. The amount of finasteride in the diffusion cell and mouse skin was measured by HPLC. The hair growth was evaluated using depilated male C57BL/6N mice. Mean particle size of all finasteride-containing liposomes was less than a micron, and polydispersity index revealed size homogeneity. Skin penetration and retention studies showed that significantly less amount of finasteride was penetrated when applied as anionic liposome while more amount of the drug was retained. Specifically, in liposome prepared with 10% anionic charge carrier lipid, penetration was 12.99 ${\mu}g/cm^2$ while retention was 79.23 ${\mu}g/cm^2$ after 24 h of application. In hair growth study, finasteride-containing anionic liposomes showed moderate efficacy, but the efficacy was not found when applied as cationic liposomes. In conclusion, topical application of finasteride using anionic liposome formulation appears to be useful option for the treatment of androgenetic alopecia to avoid systemic side effects of the drug.

• Tribology and Lubricants
• /
• v.34 no.3
• /
• pp.75-83
• /
• 2018

Microturbomachinery (< 250 kW) using gas foil bearings can function without oil lubricants, simplify rotor-bearing systems, and demonstrate excellent rotordynamic stability at high speeds. State-of-the-art technologies generally use bump foil bearings or leaf foil bearings due to the specific advantages of each of the two types. Although these two types of bearings have been studied extensively, there are very few studies on leaf-bump foil bearings, which are a combination of the two aforementioned bearings. In this work, we illustrate a simple mathematical model of the leaf-bump foil bearing with leaf foils supported on bumps, and predict its static and dynamic performances. The analysis uses the simple elastic model for bumps that was previously developed and verified using experimental data, adds a leaf foil model, and solves the Reynolds equation for isothermal, isoviscous, and ideal gas fluid flow. The model predicts that the drag torques of the leaf-bump foil bearings are not affected significantly by static load and bearing clearance. Due to the preload effect of the leaf foils, rotor spinning, even under null static load, generates significant hydrodynamic pressure with its peak near the trailing edge of each leaf foil. A parametric study reveals that, while the journal eccentricity and minimum film thickness decrease, the drag torque, direct stiffness, and direct damping increase with increasing bump stiffness. The journal attitude angle and cross-coupled stiffness remain nearly constant with increasing bump stiffness. Interestingly, they are significantly smaller compared to the corresponding values obtained for bump foil bearings, thus, implying favorable rotor stability performance.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.2
• /
• pp.157-168
• /
• 1994

The surface morphology, electrical properties, and optical properties of textured $SnO_2(:F)$ films according to deposition parameters such as HF and $H_2O$ content was studies. The electron concentration, resistivity, and mobility was $3{\Times}10^{20}/cm^3$, $7{\Times}10^4~9{\Times}10^4{Omega}cm$ and $18~25cm^2/V.sec$, respectively, when HF bubbling rate over 0.9 slm. The surface morphology was sharp edged pyramid shape without bubbling $H_2O$ but changed to round edged hemispherical shape when $H_2O$ was added.

• Journal of the Korean Society of Costume
• /
• v.23
• /
• pp.111-130
• /
• 1994

The purpose of this study was to illuminate eroticism represented din modern fashion. Art based on sex is very important like all of the other cultural values. But we feel that erotic art, neglected, suppressed , and persecuted for centuries, has an important contribution to make to the understanding of art, the social history of mankind, and human happiness and progress. It is our deep personal conviction that erotic art serves important social and therapeutic functions. Erotic art expresses the demand for sexual freedom-a freedom vital to individual happiness and mental well-being, And sexual freedom, in turn, cannot exist without a high degree of political and economic freedom as well. In that sense , erotic art came a truly revolutionaly message ; it demands no less than extension of freedom , not only in the sexual are, but in every sphere of social life. What is eroticism \ulcorner Eroticism must be distinguished from a mere animal reproduction . Eroticism is deeply rooted in the cultural tradition of myth, religion , customes and art. It also has a close relationship with psychological activities of our life. Eroticism is a kind of psychological revolution in the development of human civilization. Eroticism is related to different kinds of art, which express internal spirit of human especially Surrealism. Surrealism is above all a movement of the conquest and deepening of the unconscious. The exploitation of Freud's discoveries opended a new, practically unlimited path for artistic studies to Surrealism . Especially all theory of mental psychoanalysis a affected artists greatly in western art, Freud was appraised highly on his achievements by art critics in art history on his achievements by art critics in art history. As far as erotic subject matter was concerned, Surrealism provided a means of presentig it. Pop Art is not actually a movement , born at a specific time and place, nor is it an easy concept to define. The term first appeared in Great Britain during the fifties, when it referred, particularly in the decorative arts, to an inclination to go back and imitate the stereotyped images of the mass media : film, advertising , cartoons, and other popular consumer products. The eroticism expressed in Pop Art calls the modern's attentions to their devastated minds, taking advantage of the commercialized sex. Fashion has developed constantly reflecting the spiritual aspiration and social and cultural phenomona of man , and artistic steam. Eroticism in fashion is the style which expresses the internal meanings of sexuality through the texture, color, pattern , silhouette etc.

• The Journal of the Korea Contents Association
• /
• v.12 no.1
• /
• pp.112-124
• /
• 2012

The remarkable development of digital technologies and the success of 3D stereoscopic films have led to started drawing attention to stereoscopic images. The stereoscopic images have not become a passing fad in the present time unlike in the past, but have constantly showed their potentials. Unfortunately, the domestic stereoscopic images market is faced with difficulties, such as lack of the capital strength and of insufficient production infrastructure, and the production of 3D from 2D. As a result, it is not easy to produce creative stereoscopic animation contents. Therefore, in Korea, more efforts should be made in accumulating a plenty of data on production techniques. In order to make film production reflecting stereoscopy and effective stereoscopic implementation, which are necessary to produce high-quality stereoscopic contents, this thesis gave an explanation about a production technique studied on the basis of 3D graphic. Stereoscopic images are definitely one of the most promising image contents in the 21st digital contents industry. For the reason, in order to produce stereoscopic animation contents with high quality, fundamental studies on the stereoscopic images should be performed in a constant and cautions way.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.276-276
• /
• 2010

Large-area micropatterned array of Co/Ni bilayer anti-dots was fabricated using photolithography and wet etching process. The surface morphology as well as the surface topography was checked by scanning electron microscopy and atomic force microscopy, whereas the magnetic properties were studied by magneto-optical Kerr effect (MOKE) and magnetic force microscopy (MFM). Systematic studies of the magnetic-reversal mechanism, the in-plane anisotropy and the switching field properties were carried out. To get a comprehensive knowledge about the domain configuration, we also employed OOMMF simulations. It was found from the MOKE measurements that a combined effect of configurational and the magneto-crystalline anisotropy simultaneously works in such micropatterned bilayer structures. In addition, the inclusion of holes in the uniform magnetic film drastically affected the switching field. The MFM images show well-defined domain structures which are periodic in nature. The micromagnetic simulations indicate that the magnetization reversal of such a structure proceeds by formation and annihilation of domain walls, which were equally manifested by the field-dependent MFM images. The observed changes in the magnetic properties are strongly related to both the patterning that hinders the domain-wall motion and to the magneto-anisotropic bilayered structure.