• 대한기계학회논문집B
• /
• 제37권8호
• /
• pp.725-732
• /
• 2013

본 논문에서는 가는 열선 주위를 흐르는 나노유체의 대류열전달 특성을 실험을 통하여 검토하였다. 입자 혼합 농도가 다른 4개의 나노엔진오일에 대하여 열선온도가 증가하는 경우, 유체온도가 증가하는 경우 그리고 막온도가 일정하게 유지되는 경우 등 세가지 온도경계조건에 대하여 대류열전달계수를 측정하였다. 내부유동에서 나노유체의 대류열전달계수 상승이 열전도율 상승을 초과한다는 결과가 최근 발표되기도 했지만 본 연구에서는 이 결과를 확인할 수 없었다. 온도조건에 따른 대류열전달계수의 변화 거동을 분석함으로써 나노유체의 열전도율과 경계층두께의 관계를 설명할 수 있었다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.525-528
• /
• 2004

The ion-induced secondary electron emission coefficient ${\gamma}$ and work function for MgO thin film with $O_2$ plasma treatment has been investigated by ${\gamma}$ -FIB (focused ion beam) system. The MgO thin film deposited from sintered material with $O_2$ plasma treatment is found to have higher ${\gamma}$ and lower work function than those without $O_2$ plasma treatment. The energy of various ions used has been ranged from 100eV to 200eV throughout this experiment. It is found that the highest secondary electron emission coefficient ${\gamma}$ has been achieved for 10 minutes of $O_2$ plasma treatment under RF power of 50W.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.507-510
• /
• 2004

Oblique ion-induced secondary electron emission coefficient(${\gamma}$) with low energy ..and work function ${\phi}_{\omega}$(${\theta}$ = 0 and ${\theta}$ = 20) of the MgO thin film in AC-PDPs has been measured by ${\gamma}$-FIB system. The MgO thin film has been deposited from sintered material under electron beam evaporation method. The energy of $He^+$ ions used has been ranged from 50eV to 150eV. Oblique ion beam has been chosen to be 10 degree, 20 degree and 30 degree. It is found that the higher secondary electron emission coefficient(${\gamma}$) has been achieved by the higher oblique ion beam up to inclination angle of 30 degree than the perpendicular incident ion beam.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1315-1320
• /
• 2003

The thermal expansion coefficient, which causes the micro failure at the interfacial state of thin films is necessary to consider for proper designing MEMS. The effect of temperature on the coefficient of thermal expansion(CTE) of $SiO_2$ and $Si_3N_4$ film was investigated. Thermal strain induced by mismatch of CTE between substrate and thin film continuously measured with resolution-improved electronic speckle pattern interferometry(ESPI). The thermal stress induced by mismatch of CTE derivate through thermal strain. The thermal expansion coefficients of thin film were calculated with the general equation of CTE and thermal stress in thin films, and it confirmed that CTE of $SiO_2$changed from $0.25{\times}10^{-6}/^{\circ}C$ to $1.4{\times}10^{-6}/^{\circ}C$ with temperature increasing from 50 to $600^{\circ}C$

• KSTLE International Journal
• /
• 제3권1호
• /
• pp.38-42
• /
• 2002

Diamond-like Carbon(DLC) films were deposited on Si wafers by an RF-plasma-assisted CVD using CH$_4$gas. Tribological tests were conducted with the use of a rotating type ball on a disk friction tester with dry air. This study made use of four kinds of mating balls that were made with stainless steel but subjected to different annealing conditions in order to achieve different levels of hardness. In all load conditions, testing results demonstrated that the harder the mating materials, the lower the friction coefficient was. The friction coefficients were fecund to be lower with austenite mating balls than with fully annealed martensite balls. Conversely, the high friction coefficient found in soft martensite balls appeared to be caused by the larger contact area between the DLC film and the ball. The wear tracks on DLC films and mating balls could prove that effect. Measuring the wear track of both DLC films and mating balls revealed a similar tendency compared to the results of friction coefficients. The wear rate of austenite balls was also less than that of fully annealed martensite balls. Friction eoefficients decrease when applied leads exceed critical amount. The wear track on mating balls showed that a certain amount of material transfer occurs from the DLC film to the mating ball during a high friction process. Raman Spectra analysis Showed that the transferred materials were a kind of graphite and that the contact surface of the DLC film seemed to undergo a phase transition from carbon to graphite during the high friction process.

• 한국재료학회지
• /
• 제21권8호
• /
• pp.456-460
• /
• 2011

Microelectromechanical systems (MEMS)-fabricated suspended devices were used to measure the in-plane electrical conductivity, Seebeck coefficient, and thermal conductivity of 304 nm and 516 nm thick InGaAlAs films with 0.3% ErAs nanoparticle inclusions by volume. The suspended device allows comprehensive thermoelectric property measurements from a single thin film or nanowire sample. Both thin film samples have identical material compositions and the sole difference is in the sample thickness. The measured Seebeck coefficient, electrical conductivity, and thermal conductivity were all larger in magnitude for the thicker sample. While the relative change in values was dependent on the temperature, the thermal conductivity demonstrated the largest decrease for the thinner sample in the measurement temperature range of 325 K to 425 K. This could be a result of the increased phonon scattering due to the surface defects and included ErAs nanoparticles. Similar to the results from other material systems, the combination of the measured data resulted in higher values of the thermoelectric figure of merit (ZT) for the thinner sample; this result supports the theory that the reduced dimensionality, such as in twodimensional thin films or one-dimensional nanowires, can enhance the thermoelectric figure of merit compared with bulk threedimensional materials. The results strengthen and provide a possible direction in locating and optimizing thermoelectric materials for energy applications.

• Journal of the Korean Wood Science and Technology
• /
• 제26권4호
• /
• pp.26-33
• /
• 1998

Acoustical properties of chestnut and paulownia woods have been determined in four film thicknesses of oriental lacquering and cashew varnishing on double surfaces of soundboard to elucidate effects of finishing. Accelerometer was attached to the specimen at one third position from one end, and specimen was hit by the impact hammer at one third position from opposite end. Data were processed by vibration analyzer. The ratio of axial-to-transverse sound velocity of untreated specimens of chestnut and paulownia were 3.25 and 5.34, respectively. Natural frequency, specific Young's modulus, acoustical coefficient, sound velocity, damping of sound radiation(DSR) and acoustical converting efficiency(ACE) decreased by oriental lacquering and cashew varnishing for both species. Damping of internal friction of chestnut decreased by oriental lacquering and cashew varnishing, but that of paulownia increased. Natural frequency. specific Young's modulus, acoustical coefficient, sound velocity, and DSR decreased with increased film thickness of both finishing materials. However, damping of internal friction and ACE showed irregular tendency with increased film thickness. Acoustical properties of cashew varnished chestnut specimen were better than those of oriental lacquered specimen. Acoustical properties of oriental lacquered paulownia specimen were better than those of cashew varnished specimen.

• Nuclear Engineering and Technology
• /
• 제55권8호
• /
• pp.2905-2918
• /
• 2023

The valve assembly used in nuclear power plants is important safety-related equipment. In the new standard, the physical attributes are measured using a valve diagnosis test, which is used in the expansion to other non-tested valves using a quantitative test-basis methodology. With a motor-operated actuator, the state of stem's lubrication is related to physical attributes such as the stem factor and the friction coefficient. This study analyzed the numerical transient of fluid and solid lubrication with a squeeze film effect due to the loading rate on the stem and the stem nut using the experimental data. The differential equation that governs the motion mechanism of the stem and stem nut is established and analyzed. The flow rate, the fluid and the solid contact forces are calculated with the friction coefficient. Finally, we found that a change in the friction coefficient results from a change of the shear force in the solid contact mode during the interchange process between the solid contact mode and the fluid contact mode. The qualitative understanding of the squeeze film effect is expanded quantitatively for forces, thread surface distance, velocity, and acceleration, with consideration of the metal solid contact and fluid contact.

• Tribology and Lubricants
• /
• 제24권3호
• /
• pp.133-139
• /
• 2008

In recently designed diesel engines, the running conditions for piston pin bearings have become very severe due to combustion pressure and temperature increase. In this paper, it will be investigated the tendency of piston pin rotating motion by calculating the friction coefficient at piston pin bearings, the oil film thickness and the frictional torques induced by hydrodynamic shear stress. Finally, the pressure distributions on the oil film of piston pin bearings will be found by two-dimensional lubrication analysis in order to help the optimum design of the bearings of piston pin. Specially, it is investigated the effects on the film pressure distribution due to the change in maximum combustion pressure.

• Macromolecular Research
• /
• 제9권1호
• /
• pp.1-19
• /
• 2001

Poly(p-phenylene pyromellitimide) and poly(4,4'-biphenylene pyromellitimide) are representatives of fully rod-like polyimides. Their structure and properties in thin films are reviewed. The polymers exhibit some excellent properties such as high molecular packing coefficient, high mechanical modulus, and low thermal expansion coefficient, and low interfacial stress, so that they are very attractive to both industry and academia. However, these polymers are very brittle and thus practically useless. Some chemical modifications to improve such drawback with a little sacrifice of the high modulus are described: i) incorporation of short side groups into the polymer backbone and ii) insertion of proper linkages into the polymer backbone.