• Journal of Welding and Joining
• /
• 제16권5호
• /
• pp.134-141
• /
• 1998

In this study, a fillet size for bending fatigue strength of one side fillet welded T-joint, used in box type girder and other welding structure, was investigated by bending fatigue test with or without edge preparation and burn through, with variation of joint shape. As a result, the following conclusions were obtained. (1) In one side fillet welded T-joint, the larger the leg length, the greater the bending fatigue strength. The increase in bending fatigue strength. (2) One side filet welded T-joint with edge preparation showed higher bending fatigue strength than that with twofold-large leg length and without edge preparation. (3) In one side fillet welded T-joint without edge preparation, both manual welding and automatic welding were carried out with same condition. In this case, automatic welding shoed deeper penetration and more increased horizontal leg length than manual welding, so that automatic welding offers grater bending fatigue strength. (4) For one side fillet welded T-joint without edge preparation, the ratio(h/t) of the leg length (h) and the main plate thickness (t) in which toe crack can occur was 1.2 over. (5) In one side fillet welded T-joint with edge preparation, the burn through led to reduced bending fatigue strength. However, this bending fatigue strength was higher than that of one side fillet welded T-joint without edge preparation and with a larger leg length.

• 한국강구조학회 논문집
• /
• 제11권3호통권40호
• /
• pp.319-327
• /
• 1999

본 연구는 필렛용접 이음으로 된 종리브 십자 시험체를 대상으로 용접토우의 후처리에 의한 피로강도 향상의 메커니즘을 밝히고, 적절한 후처리법을 제안하고자 한다. 인장피로시험 결과, 용접 그대로의 시험체 보다는 후처리된 시험체들에서 피로강도 향상이 보였다. 특히, 피로균열 발생수명 $N_c$는 해머피닝(Hammer-Peening)후 그라인더 처리를 한 시험체에서, 그리고 피로균열 진전수명 $N_p$는 해머피닝 시험체 들에서 각각 증가현상을 보였다. 여기서, $N_c$는 용접토우의 기하학적 형상, 즉 응력집중의 완화때문에, 또한 $N_p$는 해머피닝에 의해 표면에 도입된 큰 압축잔류응력이 피로균열의 진전을 억제하고 있기 때문이라고 생각된다.

• Journal of Welding and Joining
• /
• 제21권1호
• /
• pp.60-65
• /
• 2003

At present. welding of most pipes with large diameter is carried out by the manual process. Automation of the welding process is necessary f3r the sake of consistent weld quality and improvement in productivity. In this study, two vision sensors, based on the optical triangulation, were used to obtain the information for seam tracking and detecting the weld defects. Through utilization of the vision sensors, noises were removed, images and 3D information obtained and positions of the feature points detected. The aforementioned process provided the seam and leg position data, calculated the magnitude of the gap, fillet area and leg length and judged the weld defects by ISO 5817. Noises in the images were removed by using the gradient values of the laser stripe's coordinates and various feature points were detected by using an algorithm based on the iterative polygon approximation method. Since the process time is very important, all the aforementioned processes should be conducted during welding.

• 한국해양공학회지
• /
• 제18권1호
• /
• pp.35-40
• /
• 2004

This paper is concerned with the simulator's ability to estimate deformation due to welding of panel blocks. An efficient computer program system has been developed which can be applied both to estimation of weld-induced deformation, under the given welding conditions, and to reflection of effect when methods for deformation control of are applied. This paper briefly describes the background of the present simulator and shows some results applying the simulator to the estimation of weld-induced deformation. In addition, the results when methods for deformation control are applied are also included.

• International Journal of Korean Welding Society
• /
• 제1권2호
• /
• pp.1-6
• /
• 2001

A weld quality assessment method is proposed in this work, which can be applied to the short-circuit mode in GMAW. Information about the welding signal trajectory, distribution of the signal duration at each sub-regions and short-circuit frequency is used to evaluate the weld quality. The weighted penalty, which is determined experimentally, is imposed for each abnormal signal. Performance of the proposed method is compared with the Simpson's method under the conditions of shielding gas reduction, workpiece surface contamination and joint gap in the butt and fillet welds. Although the proposed method predicts the weld quality with reasonable accuracy, further modification and extension to other metal transfer modes are needed as a further study.

• 한국기계가공학회지
• /
• 제6권1호
• /
• pp.20-26
• /
• 2007

In this study, fatigue strength of load-carrying cruciform fillet welded joints were evaluated using a new method proposed by Yamada, for geometric or structural stress in welded joint, that is, one-millimeter stress below the surface in the direction corresponding to the expected crack path. Validity of the method is verified by analyzing fatigue test results for load-carrying cruciform welded specimens has different size of weld toe radius, leg length and plate thickness reported in literature. Structural stress concentration factor for 1mm below the surface was calculated by finite element analysis for each specimen respectively. When compared to the basic fatigue resistance curve offered by BS7608, the one-millimeter stress method shows conservative evaluation for load-carrying cruciform fillet welded joints.

• Journal of Welding and Joining
• /
• 제28권3호
• /
• pp.59-64
• /
• 2010

The purpose of this study is to identify the principal factor controlling transverse residual stress at the weldment for joining unit hull blocks. In order to do it, the comprehensive FE analyses were carried out to evaluate the effect of distance between fillet and butt weldments, stiffener span and in-plane restraint degree on the amount and distribution of transverse residual stress in way of the weldments between unit hull blocks. In accordance with FEA results, principal factor controlling the amount of transverse residual stress at the weldments was identified as in-plane restraint degree of butt weldment for unit blocks. The effect of other variables on the transverse residual stress was very small relatively.

• 대한기계학회논문집A
• /
• 제29권10호
• /
• pp.1377-1383
• /
• 2005

A general and efficient methodology has been developed to analyze dimensional variations of an assembly, taking into account of weld distortion. Weld distortion is generally probabilistic because of the random nature of welding parameters such as the welding speed, maximum welding temperature, ambient temperature, etc. The methodology is illustrated through a very simple example of two perpendicular plates fillet-welded to each other. Two steps comprise the methodology: establishment of a weld-distortion database, and tolerance analysis using the database. To establish the database, thermo-elasto-plastic finite element analyses are conducted to compute the weld distortion for all combinations of discrete values of major welding parameters. In the second step of tolerance analysis, the weld distortion retrieved from the database is used in addition to the dimensional tolerances of the parts. As a result of such an analysis, sensitivities of the assembly's dimensional variations to the part tolerances and weld distortion are obtained, which can be help improve the dimensional quality of the assembly.

• International Journal of Korean Welding Society
• /
• 제4권1호
• /
• pp.30-37
• /
• 2004

There have been continuous efforts on automating welding processes. This automation process could be said to fall into two categories, weld seam tracking and weld quality evaluation. Recently, the attempts to achieve these two functions simultaneously are on the increase. For the study presented in this paper, a vision sensor is made, a vision system is constructed and using this, the 3 dimensional geometry of the bead is measured on-line. For the application as in welding, which is the characteristic of nonlinear process, a fuzzy controller is designed. And with this, an adaptive control system is proposed which acquires the bead height and the coordinates of the point on the bead along the horizontal fillet joint, performs seam tracking with those data, and also at the same time, controls the bead geometry to a uniform shape. A communication system, which enables the communication with the industrial robot, is designed to control the bead geometry and to track the weld seam. Experiments are made with varied offset angles from the pre-taught weld path, and they showed the adaptive system works favorable results.

• Journal of Welding and Joining
• /
• 제14권2호
• /
• pp.96-105
• /
• 1996

Robot systems are widely utilized in the shipbuilding industry to enhance the productivity by automating the welding process. In order to increase productivity, it is necessary to reduce the time used for robot teaching. In this work, the automatic teaching system is developed for the subassembly process in the shipbuilding industry. A alser/vision sensor is designed to detect the weld seam and the image of the fillet joint is processed using the arm method. Positions of weld seams defined in the CAD database are transformed into the robot coordinate, and the dynamic programming technique is applied to find the sub-optimum weld path. Experiments are carried out to verify the system performance. The results show that the proposed automatic teaching system performs successfully and can be applied to the robot system in the subassembly process.