• Journal of the Korean Wood Science and Technology
• /
• 제42권5호
• /
• pp.510-515
• /
• 2014

The anatomical and physical properties of tension wood (TW), opposite wood (OW) and lateral wood (LW) in the branches of Korean paulownia (Paulownia coreana) were compared. The diameter of TW vessels was larger than that of OW and LW vessels. The most distinctive feature of TW fibers was the presence of a gelatinous layer (G-fiber). The cell wall of TW fibers was nearly three times as thick as that of OW and LW. TW differed from OW and LW in density, X-ray diffraction pattern and shear and compressive strengths. The results obtained in this study showed clear differences in the anatomical and physical properties of TW, OW and LW of Paulownia coreana branch woods.

• Journal of the Korean Wood Science and Technology
• /
• 제44권4호
• /
• pp.505-514
• /
• 2016

To study mechanical properties of fiberglass reinforced wood-based composite (FRWC), fiberglass with a diameter of $20{\mu}m$ was selected to prepare test specimens. Mechanical properties of fiberglass reinforced wood-based composite were determined by three-point-bending test while its microstructure was characterizes by scanning electron microscopy (SEM). The results showed that mechanical properties of fiberglass reinforced wood-based composite were superior to that of the wood fiberboard based on the contrasting mechanical curves and the analysis of fracture mechanism. It is believed that the material design with this "sandwich" structure brings a unique buffering capacity of fiberglass into play in the composites. So the specimen did not produce a sudden fracture failure at high level of applied loads because it had a bearing ability. The SEM analysis showed that the working strength of PVAc adhesive was high; under a bearing force, it could properly transfer a load. In addition, glass fiber mesh and wood fiber board combined well.

• 한국건설순환자원학회논문집
• /
• 제3권1호
• /
• pp.80-86
• /
• 2007

In this study we experimented setting time and basic properties as waste wood fiber and sodium silicate substitution rate to reuse waste wood fiber produced in construction field to wood chip board. To do this construction waste woods were crushed with the size less than 10mm, mixed with the rate of 1:2, 2.5, 3, and added sodium silicate with the rate of 0, 5% of cement content. The results are as follows. As the substitution rate of construction waste wood was increased delay of setting time was also increased, and the batch of adding 5% accelerator had a 13~17 hours faster setting time than non accelerator batch. The compressive strength was lower as wood substitution rate was higher, and as the specific gravity was higher, the strength was also higher. As wood substitution rate was higher, heat conductivity was lower, and as specific gravity was higher, heat conductivity also was higher.

• 펄프종이기술
• /
• 제43권1호
• /
• pp.1-10
• /
• 2011

To investigate the combination dyeing properties of natural dyes, the combination dyeing using gallnut,-Al, Cu, Fe-sappan wood, and gallnut-Al, Cu, Fe-gardenia was performed on bast fiber of mulberry, cotton, silk, and their K/S values, colors, and sunlight fastness were measured. The gallnut-Al, Cu, Fe-gardenia dyeing showed the highest K/S values when the dyeing concentration of gallnut is 3%. It tended to show the higher K/S values than gallnut-Al, Cu, Fe-sappan wood. The silk showed the highest values of in K/S, and then followed by cotton, and bast fiber of mulberry. The mordants developed different colors on the bast fiber and the cotton treated with gallnut-Al, Cu, Fe-sappan wood. However, the silk showed a series of YR, showing no effect of the mordants on the development of color. The combination dyeing of gallnut-Al, Cu, Fe-gardenia showed a series of Y. The results showed that sappan wood could develop various colors but gardenia could develop a series of Y. No distinct improvement on sunlight fastness of the combination dyeing was observed.

• Journal of the Korean Wood Science and Technology
• /
• 제29권3호
• /
• pp.59-67
• /
• 2001

Rice husk flours were analyzed by chemical composition and thermogravimetric methods in nitrogen atmosphere to discuss its feasibility as a raw material for manufacturing agricultural lignocellulosic fiber-thermoplastic polymer composite. It was revealed in the chemical composition analysis that rice husk flour was composed of moisture, 5.0%; lignin, 21.6%; holocellulose, 60.8%; ash, 12.6%. In the thermogravimetric analysis (TGA), thermal decomposition behavior of rice husk flour from room temperature to $350^{\circ}C$ was similar to that of wood flour, but rice husk flour was more thermally stable from 350 to $800^{\circ}C$ than wood flour because of higher silica content in the rice husk flour and smaller particle size of rice husk flour. The activation energy of thermal decomposition was evaluated using Flynn & Wall expression. As the thermal decomposition proceeded in rice husk flour, the activation energy of thermal decomposition appeared almost constant up to ${\alpha}=0.25$, but thereafter increased. Activation energy of thermal decomposition in wood flour, however, decreased steeply up to ${\alpha}=0.3$, but thereafter remained almost constant. From the results, rice husk flour was thought be a substitute for wood flour in manufacturing agricultural lignocellulosic fiber-thermoplastic polymer composite in the aspect of thermal decomposition.

• Journal of the Korean Wood Science and Technology
• /
• 제39권4호
• /
• pp.351-358
• /
• 2011

인장이상재를 갖는 활엽수재의 파괴특성을 이해하기 위해 신갈나무재의 전단시험 및 휨시험을 통하여 파괴단면을 관찰하였다. 육안적으로 관찰한 결과 전단시편의 경우 정상재보다 인장이상재 시편에서 더 많은 섬유의 보풀이 관찰되었고, 함수율 30% 시편의 전단면이 10%보다 거칠고 많은 섬유의 보풀이 관찰되었다. 휨시험에 의해 파괴된 인장이상재는 정상재에 비해 목섬유가 굵고 길게 드러나 있는 것이 관찰되었다. SEM 관찰 결과 방사면 전단파괴시 정상재와 인장이상재의 목섬유는 벽내파괴에 의한 파괴형태를 보여주고 있으며, 방사유세포는 벽절단파괴에 가까운 형태로 파괴되었다. 접선면 전단파괴시 목섬유는 벽내파괴에 의한 파괴형태를 보여주고 있고 인장이상재의 목섬유의 파괴부분이 더 거칠었다. 방사유세포는 양 시편 모두 벽절단파괴에 의한 파괴 형태를 보여주었으며, 인장이상재의 방사유세포에서 절단면이 비교적 깨끗한 것으로 나타났다. 휨시험에 의한 목섬유 파면의 형태는 정상재의 목섬유에 비하여 인장이상재가 파괴 시 끝이 무디고 깨끗하게 끊어진 모습을 보여주었다.

• 한국가구학회지
• /
• 제18권2호
• /
• pp.161-165
• /
• 2007

An experiment was conducted to observe the safranine flow depth in longitudinal direction of Populus tomentiglandulosa. Longitudinal flow of safranine was considered from bottom to top end of the tree. Vessel and wood fiber were considered for the measurement of safranine flow depth. It was found that sapwood conducted safranine 12.25% higher in longitudinal direction compared with heartwood. Vessel was found the main avenue for safranine flow. Vessel conducted safranine 41.94% higher than that of wood fiber. Safranine penetrated through vessel and fiber forming a curved meniscus.

• 펄프종이기술
• /
• 제45권6호
• /
• pp.30-35
• /
• 2013

To conserve wood resources for papermaking, chemical compositions of the hemp (Cannabis sativa L.) bast fiber cultivated in Korea such as holocellulose, ${\alpha}$-cellulose, lignin, alcohol-benzene extractives, hot and cold water extractives, and ash contents were investigated to manufacture the specialty packaging paper effectively. Significantly very low klason lignin content of 3.3% was accomplished by removing of the outer shell of bark. Laboratory soda pulping method which is very useful for the nonwood fiber was adapted, and it was found that there was no significant difference in both kappa number and H-factor between 25% and 30% NaOH charge. Hemp pulp cooked with the laboratory digester in 25% NaOH at $170^{\circ}C$ were mixed together with the wood pulp(NBKP:LBKP=1:1) in order to find the optimum mixture ratio which exhibited acceptable paper strength properties such as tensile index, burst index, and tear strength. When 10% of hemp soda pulps was mixed with 90% of wood pulps comprised of SwBKP and HwBKP (1:1), all physical strength increased significantly. The physical strength decreased as the amount of hemp pulp increased because the cell wall of bast fiber is very thick which causes low conformability and low fiber-fiber bonding. These results showed that paper made of hemp-wood pulp can be used for the specialty packaging paper which requires both the characteristic surface properties and the high physical strength of hemp fiber.

• Journal of the Korean Wood Science and Technology
• /
• 제43권5호
• /
• pp.652-660
• /
• 2015

To study the bearing characteristics of glass fiber reinforced glulam for structural design, bearing strength tests were performed. Bearing loads were applied in the direction parallel to the grains, and the holes were prepared in such a way that the bolts would bear and support all the layers. The yield bearing strengths of the glass fiber reinforced glulam were found to be similar to those of the non-reinforced glulam, and were almost constant regardless of increases in bolt diameter. The ratio of the experimental yield bearing strength to the estimated bearing strength according to the suggested equation of the Korea Building Code and National Design Specification was 0.91~1.03. For the non-reinforced glulam and the sheet glass fiber reinforced plastic glulam, the maximum bearing load was measured according to the splitting fracture of specimens under bolt. The textile glass fiber reinforced glulam underwent only an embedding failure caused by the bearing load. The failure mode of reinforced glulam according to bearing load will influence the failure behavior of bolted connection, and estimating the shear yield strength of the bolted connection of the reinforced glulam is necessary, not only by using the bearing strength characteristics but also using the fracture toughness of the reinforced glulam.

• Journal of the Korean Wood Science and Technology
• /
• 제26권1호
• /
• pp.76-86
• /
• 1998

Effects of processing variables and MAPP (maleic anhydride polypropylene) coupling agent on the properties of composite were discussed for turbulent-air-mixed woodfiber-polypropylenefiber composites. In this research, density, composition ratio, and mat moisture content were established as processing variables, and emulsified MAPP prepared by direct pressure method was incorporated as the coupling agent. And the turbulent air mixer, which was improved in function through alteration of our previous fiber mixer, was used to mix wood fibers and polypropylene fibers. At the addition level of 1% MAPP, based on oven-dried wood fiber weight, woodfiber-polypropylenefiber composites generally showed enhanced the physical and mechanical properties. And composites with low to medium densities of 0.6 to 0.8g/$cm^3$ greatly increased in these property values than with high densities of 1.0g/$cm^3$ or more by adding 1 % MAPP. Thus, MAPP addition was thought to be an effective way of enhancing properties for nonwoven web composites. At the mat moisture contents of 5 to 20%, however, the physical and mechanical properties were not enhanced by adding 1% MAPP. In the composites containing 15% polypropylene fibers, the lowest thickness swelling and water absorption values were observed at the 1% MAPP level. The addition of more than 1% MAPP had the adverse effect on the physical and mechanical properties of composites.