• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.60-65
• /
• 2005

The electrosorption of U(VI) from waste water was carried out by using activated carbon fiber(ACF) felt electrode in a continuous electrosorption cell. In order to enhance the electrosorption capacity at lower potential, ACF felt was chemically modified in acidic, basic and neutral solution. Pore structure and functional groups of chemically modified ACF were examined, and the effect of treatment conditions was studied for the adsorption of U(VI). Specific surface area of all ACFs decreases by this treatment. The amount of acidic functional groups decreases with basic and neutral salt treatment, while the amount increases a lot with acidic treatment. The electrosorption capacity of U(VI) decreases on using the acid treated electrode due to the shielding effect of acidic functional groups. Base treated electrode enhances the capacity due to the reduction of acidic functional groups. The electrosorption amount of U(VI) on the base treated electrode at -0.3 V corresponds to that of ACF electrode at -0.9 V. Such a good adsorption capacity was not only due to the reduction of shielding effect but also the increase of $OH^-$ in the electric double layer on ACF surface by the application of negative potential.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.42-45
• /
• 2003

Nondestructive damage sensing and mechanical properties for acid-treated carbon nanotube (CNT) and nanofiber (CNF)/epoxy composites were investigated using electro-micromechanical technique and acoustic emission (AE). Carbon black (CB) was used to compare to CNT and CNF. The results were compared to the untreated case. The fracture of carbon fiber was detected by nondestructive acoustic emission (AE) relating to electrical resistivity under double-matrix composites test. Sensing for fiber tension was performed by electro-pullout test under uniform cyclic strain. The sensitivity for fiber damage such as fiber fracture and fiber tension was the highest for CNT/epoxy composites. Reinforcing effect of CNT obtained from apparent modulus measurement was the highest in the same content. For surface treatment case, the damage sensitivity and reinforcing effect were higher than those of the untreated case. The results obtained from sensing fiber damage were correlated with the morphological observation of nano-scale structure using FE-SEM. The information on fiber damage and matrix deformation and reinforcing effect of carbon nanocomposites could be obtained from electrical resistivity measurement as a new concept of nondestructive evaluation.

• Polymer(Korea)
• /
• v.26 no.6
• /
• pp.718-727
• /
• 2002

In this work, an Ar+ beam was irradiated on carbon fiber surfaces to improve the interfacial shear strength (IFSS) of the resulting composites using an ion assisted reaction (IAR) method h single fiber pull-out test was executed to investigate the basic characteristics of the single Carbon fiber/matrix interface. Based on Greszczuk's geometrical model, the debonding force for pull-out of the fiber from the resins was discussed with the applied ion beam energy as a result, it was known that an ion beam treatment produced the functional groups on fiber surface and etching lines along the fiber axis direction, resulting in increasing the adhesion forces between fibers and matrix, which caused the improvement of the IFSS in a composite system. And, it was also found that the maximum IFSS was shown at 0.8 keV ion beam energy in this system.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.2
• /
• pp.1-7
• /
• 2000

In the previous experiment, it was found that OCC pre-treatment with Hobart mixer at 20-25％ consistency for 3 hrs or more followed by the application of the equal refining time, caused the increase of tensile strength, burst strength, compressive strength and tear resistance, compared to the no pre-treated. Four completely different fibers, which were Hw-BKP, Sw-BKP, White ledger, and OCC were selected for this experiment to investigate the effect of mechanical pre-treatment process on different fibers. From the experiment, it was found that the mechanical pre-treatment did not decrease fiber length at all, but decreased freeness, com-pared to the no pre-treated, when the same refining time was applied. WRVs of the pre-treated fibers were higher than the no pre-treated at the same freeness level. It was speculated that the mechanical pre-treatment induced only hydrophilic nature of fibers without damaging fiber length by delaminating fiber walls. The fiber surface area and the physical strength differences of handsheets will be discussed in the next publication.

• Advanced Composite Materials
• /
• v.16 no.4
• /
• pp.299-314
• /
• 2007

In the present study, natural fibers (jute, kenaf and henequen) reinforced thermoplastic (poly(lactic acid) and polypropylene) and thermosetting (unsaturated polyester) matrix composites were well fabricated by a compression molding technique using all chopped natural fibers of about 10 mm long, respectively. Prior to green composite fabrication, natural fiber bundles were surface-treated with tap water by static soaking and dynamic ultrasonication methods, respectively. The interfacial shear strength, flexural properties, and dynamic mechanical properties of each green composite system were investigated by means of single fiber microbonding test, 3-point flexural test, and dynamic mechanical analysis, respectively. The result indicated that the properties of the polymeric resins were significantly improved by incorporating the natural fibers into the resin matrix and also the properties of untreated green composites were further improved by the water treatment done to the natural fibers used. Also, the property improvement of natural fiber-reinforced green composites strongly depended on the treatment method. The interfacial and mechanical results agreed with each other.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.04a
• /
• pp.69-69
• /
• 2000

In the previous experiment, it was found that OCC pre-treatment with Hobat mixer at 20-25% consistency for 3 hrs or more followed by the application of the equal refining time, caused the increase of tensile strength, burst strength, compressive strength and tear resistance, compared to the no pre-treated. Four completely different fibers, which were Hw-BKP, Sw-BKP, White ledger, and OCC were selected for this experiment to investigate the effect of mechanical pre-treatment process on different fibers. From the experiment, it was found that the mechanical pre-treatment did not decrease fiber length at all, but decreased freeness, compared to the no pre-treated, when the same refining time was applied WRVs of the pre-treated fibers were higher than the no pre-treated at the same freeness level. It was speculated that the mechanical pre-treatment induced only hydrophilic nature of fibers without damaging fiber length by delaminating fiber walls. The fiber surface area and the physical strength differences of handsheets will be discussed in the next publication.

• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.3
• /
• pp.169-174
• /
• 1994

The reaction layer formed at interface between matrix and fiber has significant effects on the mechanical properties and behaviors of deformation m FRM. In this study, the mechanical properties and interfacial behaviors according to surface finishing on the fibers and according to heat treatment in FRM were investigated. FRM was fibricated by diffusion bonding method. In W/Al alloy composite and W/Al composite, W of which was coated with $WO_3$, the heat treatment was carried out thermal cycling method from 373K to 673K. In W/Al composite, W of which was coated with $WO_3$, growth of interface layer was hardly occured in spite of the increasing various thermal cycles. It was exhibited that oxidized W/Al composite were higher strength than non-oxidezed W/Al composite with the increasing thermal cycles. The compounds of fiber/matrix interface were analyzed into $WAl_{12}$, $WAl_7$, and $AlWO_3$, respectivly. Therefore the interfacial compounds of fiber/matrix seriously affected the mechanical properties and behaviors of deformation in FRM.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.3 no.1
• /
• pp.15-31
• /
• 2001

Textile fabrication affected by consumer and selected by fashion designer. The textile fabrication has been made not only by introducing the newly developed fiber but also by modifying the existing textile materials to impart sensibility to them. Consumers choose but to their sensibility of textile material and fashion trend. On purpose in this research is find out have influence on textile image. Wool fabrics have been in use from early age in northern Europe. Recognition of the role of the morphological structure, surface properties, chemical composition, acid-base characteristics in the chemical treatment of wool led to quantum advances in the fields of setting, shrink-resisting, chemical modification, and internal fiber cross-linking. Mechanical finishing to develop the handle, drape, and surface characteristics of the fabric is at least as important as chemical or wet finishing. Result showed that to have variety sensibility and trend theme in wool fabrics are tweed, venetian, serge, gabardine and melton.

• Carbon letters
• /
• v.5 no.4
• /
• pp.191-196
• /
• 2004

The electrochemical removal (ECR) of water pollutants by activated carbon fiber (ACF) electrodes from wastewater was investigated over wide range of electrochemical reaction time. The ECR capacities of ACF electrodes were associated with their internal porosity and were related to physical properties and to reaction time. And, surface morphologies and elemental analysis for the ACFs after electrochemical reaction are investigated by SEM and EDX to explain the changes in adsorption properties. The FT-IR spectra of ACFs for the investigation of functional groups show that the electrochemical treatment is consequently associated with the homogeneous removal of pollutants with the increasing surface reactivity of the activated carbon fiber surfaces. The ACFs were electrochemically reacted to waste water to investigate the removal efficiency for the COD, T-N and T-P. From these removal results of pollutants using ACFs substrate, satisfactory removal performance was obtained. The outstanding removal effects of the ACFs substrate were determined by the properties of the material for adsorption and trapping of organics, and catalytic effects.

• Fibers and Polymers
• /
• v.2 no.2
• /
• pp.58-63
• /
• 2001

Silk fibroin (SF) was dissolved in calcium chloride/ethanol/water mixture(1/2/8 in mole ratio) at $70^{\circ}C$ for 4h. The dissolved silk fibroin was regenerated by casting the dialyzed solution into films. The films were treated with 50% aqueous solution of methanol for different times, and their antithrombogenicity was evaluated by in vivo tests. In vivo blood tests were made by a method of peripheral vein indwelling suture. It was found that the silk fibroin had a good antithrombogenicity and an absorbability even though the polymer showed foreign body reaction. Finally, the blood compatibilty of silk fibroin films which were subjected to structural change by the methoanl treatment, was examined in connection with their interfacial surface energy, and a correlation between these properties was found to be present.