• Journal of Magnetics
• /
• v.14 no.3
• /
• pp.108-113
• /
• 2009

High-coercive garnet films have certain parameters suitable for creating reconfigurable magnetic atomic chips with visible geometry. However, the inner stresses and morphological properties, namely, networks of dislocations, layering and surface relief, and dependence of coercivity on thickness must be taken into account. Select features of films important for atomic trap creation have been studied experimentally and the supposed traps concept provided.

• Journal of The Korean Astronomical Society
• /
• v.27 no.1
• /
• pp.45-53
• /
• 1994

We present the calculation of X -ray spectra produced through Compton scattering of soft X-rays by hot electrons in the spherical shell geometry, using fully relativistic Monte Carlo simulation. With this model, we show that the power-law component, which has been observed in the low luminosity state of low-mass X-ray binaries (LMXBs), is explained physically. From a spectral. analysis, we find that spectral hardness is mainly due to the relative contribution of scattered component. In addition, we see that Wi en spectral features appear when the plasma is optically thick, especially in the high energy range, $E{\gtrsim}100keV$. We suggest that after a number of scattering the escape probability approaches an asymptotic form depending on the geometry of the scattering medium rather than on the initial photon spectrum.

• Structural Engineering and Mechanics
• /
• v.70 no.3
• /
• pp.367-380
• /
• 2019

The paper concerns topology and geometry optimization of statically determinate beams with arbitrary number of supports. The optimization problem is treated as a bi-criteria one, with the objectives of minimizing the absolute maximum bending moment and the maximum deflection for a uniform gravity load. The problem is formulated and solved using the Pareto optimality concept and the lexicographic ordering of the objectives. The non-dominated sorting genetic algorithm NSGA-II and the local search method are used for the optimization in the Pareto sense, whereas the genetic algorithm and the exhaustive search method for the lexicographic optimization. Trade-offs between objectives are examined and sets of Pareto-optimal solutions are provided for different topologies. Lexicographically optimal beams are found assuming that the maximum moment is a more important criterion. Exact formulas for locations and values of the maximum deflection are given for all lexicographically optimal beams of any topology and any number of supports. Topologies with lexicographically optimal geometries are classified into equivalence classes, and specific features of these classes are discussed. A qualitative principle of the division of topologies equivalent in terms of the maximum moment into topologies better and worse in terms of the maximum deflection is found.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.2
• /
• pp.236-250
• /
• 2016

Electrical Designs for Application Specific Integrated Circuits (ASIC) has undergone a change recently with the advent of the sub-wavelength lithography. The optical projection with 193 nm wavelength has been further extended with the use of immersion and other techniques. The competing trends for printing smaller design features have been discussed in this paper with the discussion of the electrical layout analysis to find unfriendly design features. The early knowledge of the unfriendly design features allows remedial actions in time for better yield on the wafer. There are existing standard design qualification criteria being used in the design and fabrication community, but they seem to be insufficient to guarantee defect free designs. This paper proposes an integrated approach for screening the layout with multiple aspects: layout geometry based, graphical analysis and process model based verification. The results have been discussed with few example design features from the 28nm design layout.

• Korean Journal of Computational Design and Engineering
• /
• v.9 no.2
• /
• pp.175-182
• /
• 2004

As a bridge between design and manufacturing, process planning is to generate a sequenced set of instructions to manufacture the specified part. Automatic interpretation of manufacturing information incorporated in the design documentation such as CAD file has been a knotty subject for manufacturing engineers since no current data exchange format for product data provides a perfect interface between heterogeneous systems. The recent neutral data exchange format STEp, standard for the exchange of product model data, includes not only geometry but also technical and managerial information. STEP AP(Application Protocol) 224 is specifically dedicated to the mechanical product definition for process planning using machining features. Given a design information in STEP AP 224 format, process planning can be made without human intervention. This paper describes a method to determine the sequence of machining features by using the machining features and the manufacturing information expressed in STEP AP224.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.3
• /
• pp.27-33
• /
• 2001

The aim of the present work is to propose a model for Computer Aided programming of numerical Control lathe. This model is based on the concept by features. It has been developed in an Artificial Intelligence environment, that offers a rapidity as well as a precision for NC code elaboration. In this study a pre-processor has been elaborated to study the geometry of turning workpiece. This pre-processor is a hybrid system which combine a module of design by features and a module of features recognition for a piece provided from an other CAD software. Then, we have conceived a processor that is the heart of the CAD/CAM software. The main functions are to study the fixture of the workpiece, to choose automatically manufacturing cycles, to choose automatically cutting tools (the most relevant), to simulate tool path of manufacturing and calculate cutting conditions, end to elaborate a typical manufacturing process. Finally, the system generates the NC program from information delivered by the processor.

• International Journal of Precision Engineering and Manufacturing
• /
• v.6 no.1
• /
• pp.65-72
• /
• 2005

Drilling process is one of the most common, yet complex operations among manufacturing processes. The performance of a drill is largely dependent upon drilling forces, Many researches focused on the effects of drill parameters on drilling forces. In this paper, an effective theoretical model to predict thrust and torque in drilling is presented. Also, with the predicted forces, the stress analysis of the drill tool is performed by the finite element method. The model uses the oblique cutting model for the cutting lips and the orthogonal cutting model for the chisel edge. Thrust and torque are calculated analytically without resorting to any drilling experiment, only by tool geometry, cutting conditions and material properties. The stress analysis is performed by the commercial FEM program ANSYS. The geometric modeling and the mesh generation of a twist drill are performed automatically. From the study, the effects of the variation of the geometric features of the drill and of the cutting conditions of the drilling on the drilling forces and the stress distributions in the tool are calculated analytically, which can be applicable for designing optimal drill geometry and for improving the drilling process.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.35 no.4
• /
• pp.25-36
• /
• 2019

Contemporary architecture is showing its deconstruction and departure from modern architecture based on rationality, such as reductionism or virtualism. This means a shift from a mechanistic and ecological world view to an organic and ecological view, from a deterministic reason to a reason for a possible secret static. This study examines the potential of fractals, a scientific theory of complexity that is emerging as a new paradigm in the 21st century, as an appropriate alternative to contemporary complexity architecture. The method and scope of this study were understood and its features were identified through literature and data research and prior study review. Based on the organic nature of fractal geometry, we analyzed the works of contemporary architects(Frank Gehry, Bernard Tschumi, Steven Holl, Zaha Hadid, Rem Koolhaas, Daniel Libeskind, Zvi Hecker, Ito Toyo) and studied the possibility of architectural design using the principle of fractal. As a result, fractal geometry, similar to the patterned order of nature, has an infinite set of organizational functionalities in architecture and can be applied in various aspects of design analysis. Architectural designs based on the fractal theory will require more research and development to realize dynamic design representation using digital computers.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.3856-3863
• /
• 2012

A 3D reconstruction technique from stereo images that requires minimal intervention from the user has been developed. The reconstruction problem consists of three steps of estimating specific geometry groups. The first step is estimating the epipolar geometry that exists between the stereo image pairs which includes feature matching in both images. The second is estimating the affine geometry, a process to find a special plane in the projective space by means of vanishing points. The third step, which includes camera self-calibration, is obtaining a metric geometry from which a 3D model of the scene could be obtained. The major advantage of this method is that the stereo images do not need to be calibrated for reconstruction. The results of camera calibration and reconstruction have shown the possibility of obtaining a 3D model directly from features in the images.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.4
• /
• pp.392-399
• /
• 2009

The paper concerns the description of the step by step development process of the new fixed blade runner called "Mixer" suitable for the uprating of the Francis turbines units installed at the older low head hydropower plants. In the paper the details of hydraulic and mechanical design are presented. Since the rotational speed of the new runner is significantly higher then the rotational speed of the original Francis one, the direct coupling of the turbine to the generator can be applied. The maximum efficiency at prescribed operational point was reached by the geometry optimization of two most important components. In the first step the optimization of the draft tube geometry was carried out. The condition for the draft tube geometry optimization was to design the new geometry of the draft tube within the original bad draft tube shape without any extensive civil works. The runner blade geometry optimization was carried out on the runner coupled with the draft tube domain. The blade geometry of the runner was optimized using automatic direct search optimization procedure. The method used for the objective function minimum search is a kind of the Nelder-Mead simplex method. The objective function concerns efficiency, required net head and cavitation features. After successful hydraulic design the modal and stress analysis was carried out on the prototype scale runner. The static pressure distribution from flow simulation was used as a load condition. The modal analysis in air and in water was carried out and the results were compared. The final runner was manufactured in model scale and it is going to be tested in hydraulic laboratory. Since the turbine with the fixed blade runner does not allow double regulation like in case of full Kaplan turbine, it can be profitably used mainly at power plants with smaller changes of operational conditions or in case with more units installed. The advantages are simple manufacturing, installation and therefore lower expenses and short delivery time for turbine uprating.