• 한국의류산업학회지
• /
• 제7권1호
• /
• pp.111-114
• /
• 2005

In this the study, polyester/cotton(P/C) blended fabrics with fine denier were developed to get the light weight compared with the traditional P/C blended fabrics. Moreover, the width of the fabrics was extended by the tenter during the final heat treatment to get the lower fabric density and lighter weight. Then, the physical properties of these fabrics were analysed. The results were as the follows: The developed fabrics had 22.6-31.6% lighter weight than the traditional fabrics with the same fabric width. The weight of fabric decreased drastically with the fabrics width down to 67.1 $g/m^2$. The fabric density for the warp direction decreased with the fabric width. The tenacity and the elongation of the developed fabrics was little lower than that of the traditional fabrics. The air permeability of the developed fabrics increased with that of the traditional fabrics. The stretch rate of the developed fabrics decreased with increasing the fabric width. Residual stretch rate of the developed fabrics was more stable than that of the traditional fabrics. Residual stretch rate of the developed fabrics increased with the fabric width, but the highest value was less than 5% which is quit stable.

• 한국의류산업학회지
• /
• 제22권1호
• /
• pp.112-118
• /
• 2020

This paper examined the water repellency, water proofing and water vapor permeability of twelve types of woven fabrics for sports wear clothing. Their physical properties were compared and discussed with the fabric structural parameters and surface finishing effect. A water repellent property of 100% was obtained in the coated or laminated water repellent finished fabrics; in addition, cotton/nylon breathable composite fabrics treated with a laminated finishing and with low fabric density showed a 90% water repellency. Water proofing fabric above 6,000 mm H₂O hydraulic pressure was achieved by coated or laminated finishing; however, high density fabric or medium-level coated fabrics exhibited 100% water repellent and low water proofing characteristics. Superior water vapor permeability characteristics with good water repellency and proofing properties were achieved at the 2.5 layered low density and with 0.7 - 0.9 cover factor nylon fabrics treated with hydrophilic laminated finishing. The regression analysis for examining the effects of fabric structural parameters and surface finishing such as coating and laminating to the water vapor permeability exhibited a high determination coefficient of fabric structural parameters of 63.5%; in addition,, main factors among fabric structural parameters appeared to be cover factor and fabric thickness per weight. Coating and Laminating factors exhibited determination coefficient of water vapor permeability parameters of 36.5%.

• 한국감성과학회:학술대회논문집
• /
• 한국감성과학회 2009년도 춘계학술대회
• /
• pp.177-180
• /
• 2009

This study investigates the perception of different fabrics by consumers when provided with a video clip with rustling sounds of the fabric. We utilized sportswear products that are currently on the market and evaluated the emotional response of internet shoppers by measuring the physiological and psychological responses. Three kinds of vapor-permeable water-repellent fabric were selected to generate video clips each containing the fabric rustling sound and images of exercise activities wearing the sportswear made of the respective fabric. The new experimental website contained the video clips and was compared with the original website which served as a control. 30 subjects, who had experience to buy clothing online, took part in the physiological and psychological response to the video clip. Electroen-cephalography (EEG) was used to measure the physiological response while the psychological response consisted of evaluating accurate perception of the fabric, satisfaction, and consumer interest. When we offered video clips with fabric's rustling sound on the website, subjects answered they could get more accurate and rapid information to decide to purchase the products than otherwise they do the shopping without such information. However, such rustling sounds somewhat annoy customers, as proved psychological and physiological response. Our study is a critical step in evaluating the consumer's emotional response to sportswear fabric which will promote selling frequency, reduce the return rate and aid development of new sportswear fabric further evolution of the industry.

• Fibers and Polymers
• /
• 제6권2호
• /
• pp.169-173
• /
• 2005

Low temperature plasma (LTP) treatment was applied to wool fabric with the use of a non-polymerizing gas, namely oxygen. After the LTP treatment, the fabric properties including low-stress mechanical properties, air permeability and thermal properties, were evaluated. The low-stress mechanical properties were evaluated by means of Kawabata Evaluation System Fabric (KES-F) revealing that the tensile, shearing, bending, compression and surface properties were altered after the LTP treatment. The changes in these properties are believed to be related closely to the inter-fiber and inter-yam frictional force induced by the LTP. The decrease in the air permeability of the LTP-treated wool fabric was found to be probably due to the plasma action effect on increasing in the fabric thickness and a change in fabric surface morphology. The change in the thermal properties of the LTP-treated wool fabric was in good agreement with the above findings and can be attributed to the amount of air trapped between the yams and fibers. This study suggested that the LTP treatment can influence the final properties of the wool fabric.

• 한국농공학회논문집
• /
• 제62권4호
• /
• pp.23-31
• /
• 2020

Recently, meteorological disasters have been increasing by climate change, excessive rainfall, and landslide. The purpose is to develop new fabric concrete that can prevent and recover from damages because some of areas are vulnerable to meteorological disaster. Specifically, this technology can minimize time and space constraint when repairing the concrete structure and installing a formwork. The structure of fabric concrete is a mixture of fabric concrete and a high-speed hardened cement, Silica sand, wollastonite mineral fiber, fabric material and waterproof PVC fabric. In this study, the ratio of mechanical properties and durability of the fabric concrete mixture was evaluated by deriving the binder: silica sand mix ratio of the fabric concrete mixture and substituting part of the cement amount with wollastonite mineral fiber. Best binder in performance evaluation: Silica sand mix ratio is 6: 4 and the target mechanical performance and durability are the best when over 15% wollastonite binder is replaced by silicate mineral fiber.

• 한국염색가공학회지
• /
• 제16권5호
• /
• pp.42-47
• /
• 2004

The main objective of this work is to develop melt-blown nonwoven fabric composite materials have electromagnetic shielding characteristics using thin copper film. Melt-blown nonwoven fabric is the matrix phase and thin copper films are the reinforcement of the composite materials. Thin copper films are incorporated as conductive fillers to provide the electromagnetic shielding property of the melt-blown nonwoven fabric. The width and interval of thin copper films in the nonwoven fabric are varied by changing 1, 3, 5 mm for thin copper film's width and 1, 3, 5 mm for thin copper film's interval. The shielding effectiveness(SE) of various melt-blown nonwoven fabrics is measured in the frequency range of 50 MHz to 1.8 GHz. The variations of SE of melt-blown nonwoven fabric with width and interval of thin copper films are described. Suitability of melt-blown nonwoven fabric for electromagnetic shielding applications is discussed. The results indicate that the melt-blown nonwoven fabric composite material using thin copper film can be used for the purpose of electromagnetic shielding.

• 한국의류학회지
• /
• 제45권2호
• /
• pp.335-345
• /
• 2021

The purpose of this study was to examine the effect of fabric movement on wrinkle recovery in a clothing care system and to propose an algorithm to improve wrinkle removal performance by adjusting fabric movements. With an increase in the reciprocating speed of the movement system, the number and amplitude of curves on the fabric also increased. This allowed the fabric to be applied to a larger tension, resulting in better wrinkle removal performance at higher speeds. However, even at high reciprocating speeds, wrinkles could not be removed effectively because of nodes at a few specific locations. Based on the results of fabric movement and wrinkle recovery, a complex movement algorithm was proposed with a mixture of various reciprocation speeds. It showed a 41%p (24%→65%) improvement of wrinkle recovery when compared with the conventional algorithm that showed simple fabric movement at 180 rpm. This was because the positions of nodes and antinodes changed continuously and the force by the reciprocating motion could be applied evenly to the fabric.

• Korean Chemical Engineering Research
• /
• 제48권1호
• /
• pp.121-127
• /
• 2010

본 연구의 목적은 효소법을 이용한 바이오디젤의 생산에서의 효소(lipase) 활성화를 최적화함에 있다. 효과적인 방법으로 효소를 고정하기 위해 방사선 그라프트 중합법을 이용한 부직포에 음이온 교환기인 ethanolamine과 diethylamine을 도입시켜 음이온 교환 부직포(이때 얻어진 부직포는 EtA, DEA-EtA 부직포라 함)를 합성하였다. 기존에 사용하던 다공성 중공사막의 경우 시간이 지남에 따라 막힘 현상에 따라 유속이 현저하게 줄어드는 점을 보완하고자 기공(pore size)이 $300{\mu}m$인 부직포를 선택하였다. 이 부직포에 음이온 교환기가 도입된 EtA, DEA-EtA 부직포의 최적효소 흡착 특성과 효소 활성도에 대하여 고찰하였다. 그 결과 효소 흡착량은 EtA, DEA-EtA 부직포가 비슷하였으나(EtA non-woven fabric: 15.69 mg/g, DEA-EtA non-woven fabric: 14.45 mg/g) 기름을 투과시킨 결과 효소 활성화는 DEA-EtA 부직포가 EtA 부직포에 비해 현저히 떨어짐(EtA non-woven fabric: $3.50mol/h{\cdot}kg$, DEA-EtA non-woven fabric: $0.38mol/h{\cdot}kg$)을 알 수 있었다. 이 음이온교환기를 이용해 효율적인 바이오디젤 생산을 위한 온도, 효소고정량, 기름과 알코올과의 관계 등의 최적의 조건을 도출하였다.

• 복식
• /
• 제54권1호
• /
• pp.1-10
• /
• 2004

The purpose of this study was to compare the efficiency of four different cleaning method of silk and to fabrics, which were excavated from the sixteenth century tombs. The four cleaning methods were hand washing in water and hand washing in solvent, washing in ultrasonic cleaner, and using of ultrasonic gun after washing in ultrasonic cleaner. The following is the result of the experiment: ㆍBoth silk and jute fabrics shrank the most after hand-wash in water. This cleaning method decreased their thickness the most but changed their strength the least. However, the color of the fabric changed the most after had-wash in water. This washing method might discolor the dyed fabric, so one must check the condition of the fabric thoroughly before washing it. ㆍThe weight and the thickness of the fabric changed little after ultrasonic cleaning. This cleaning method, therefore. is less efficient than hand-water-wash. The use of ultrasonic gun after ultrasonic wash for partial cleansing enhanced the efficiency a little. Nevertheless, this method left stain around the area where the gun was used, and the injected water could damage the fabric. ㆍThe excavated fabric became softer in the cleaning process as the dirt was washed away. In both cases of silk and jute fabrics cleaning, solvent made the fabric softer than water. Washed in solvent, the fabric did not swell. But water penetrated to the fiber during the cleaning process and made the fabric swell. When the water evaporates, the swollen fiber structure collapses and the fabric become stiff. Ultrasonic wash did not cause much change in the flexibility of the fabric, for this method does not remove the dirt as effectively as the other method.

• 대한의용생체공학회:의공학회지
• /
• 제32권1호
• /
• pp.37-44
• /
• 2011

This paper describes the development and assessment of conductive fabric sensor for evaluating knee movement using bio-impedance measurement method. The proposed strip-typed conductive fabric sensor is compared with a dot-typed Ag/AgCl electrode for evaluating validity under knee movement condition. Subjects are composed of ten males($26.6{\pm}2.591$) who have not had problems on their knee. The strip-typed conductive fabric sensor is analyzed by correlation and reliability between a dot-typed Ag/AgCl electrode and the strip-typed conductive fabric sensor. The difference of bio-impedance between a dot-typed Ag/AgCl electrode and the strip-typed conductive fabric sensor averages $7.067{\pm}13.987\;{\Omega}$ As the p-value is under 0.0001 in 99% of t-distribution, the strip-typed conductive fabric sensor is correlated with a dot-typed Ag/AgCl electrode by SPSS software. The strip-typed conductive fabric sensor has reliability when it is compared with a dot-typed Ag/AgCl electrode because most of bio-impedance values are in ${\pm}1.96$ standard deviation by Bland-Altman Analysis. As a result, the strip-typed conductive fabric sensor can be used for assessing knee movement through bio-impedance measurement method as a dot-typed Ag/AgCl electrode. Futhermore, the strip-typed conductive fabric sensor is available for wearable circumstances, applications and industries in the near future.