• 한국의류산업학회지
• /
• 제7권3호
• /
• pp.327-332
• /
• 2005

The purpose of this study is to investigate the effect of chitosan treatment on the dyeing of cotton fabric specimens using loess as colorants. The wet pick up ratio of the chitosan acid solution, as well as the drying condition after the padding of the fabric specimens, was changed in order to study the loess uptake on the fabric. The average particle diameter of the loess was measured. Main components of the loess were $SiO_2$, $Al_2O_3$, and $Fe_2O_3$. By the chitosan treatment, the loess amount on the cotton fabric increased. 80% wet pick up ratio of the chitosan acid solution on the cotton fabric specimen allowed more stable and even adhesion of the loess on the fabric surface, compared to the cases of 100% and 120% wet pick up ratio.

• 한국의류산업학회지
• /
• 제8권6호
• /
• pp.702-708
• /
• 2006

The purpose of this study was to investigate the dyeing-property and antibacterial activity on nylon fabric dyed with cochineal at variable dyeing conditions. Al, Cr, Fe, Cu and Sn were used as mordants and adsorption was compared with different mordanting methods. The maximum UV-visible absorption band of cochineal extract was 495 nm. The dyeability on nylon fabric was good because of having a amine group. The optimum dyeing conditions of nylon fabrics are dyeing concentration 1.5%(o.w.s), dyeing temperature $60^{\circ}C$, pH 3 and dyeing time 30 minutes. The pre-mordanting method is preferred for Al and Cr, and the post-mordanting one is preferred for Cu, Sn and Fe to achieve better dyeing. The optimum mordanting conditions of wool fabrics dyed with cochineal are mordanting concentration of 0.5%(o.w.s), mordanting temperature $60^{\circ}C$, and dyeing time 30 minutes. Nylon fabrics dyed with cochineal show a little antibacterial activity, but it was increased by Sn mordanting. MIC test results in antibacterial activities revealed that the antibacterial activity of Cu was the highest among mordants, but Sn mordant was the most effective in antibacterial activities after mordanting treatment of nylon fabric. The fastness properties of dyed nylon fabric showd a little worse or a similar level and there was no significant difference between a mordanted and non-mordanted fabric.

• 한국의류산업학회지
• /
• 제16권2호
• /
• pp.319-325
• /
• 2014

This article describes a method for producing chitosan non-woven fabrics by just hot pressing without the use of a binder. A study has been made of the wet spinning of chitosan fiber. The fibers were rinsed thoroughly in running water and chopped wet into staples of with a length of approximately 5-10 mm. The chopped chitosan staples were dispersed uniformly in water and fabricated using a non-woven making machine. This study examined the formation and the characteristics of chitosan non-woven fabrics manufactured by hot pressing without the use of a binder. The effects of the non-woven fabrication conditions on the thermal, morphological, structural, and physical properties of chitosan non-woven fabric with and without water as a plasticizer were studied. The temperature of the exothermic peak, decomposition of chitosan fibers increased with increasing heating rate. Water in the chitosan fiber effectively plasticized the chitosan fiber. The thermal bonded structure of the wet chitosan fiber with water as a plasticizer was clearly found in many parts of the non-woven fabric at a fabrication temperature of $200^{\circ}C$. The intensity and profile of the (100) plane($2{\theta}=10.2^{\circ}$) and (040) plane($2{\theta}=20.9^{\circ}$) in the chitosan non-woven fabric decreases and became smooth in the non-woven fabric formation by melting.

• 한국의류산업학회지
• /
• 제19권4호
• /
• pp.493-503
• /
• 2017

This study investigated water vapor permeability of the 73 breathable fabrics for sports-wear according to the materials, finishing methods and fabric structural parameters. The water vapor permeability by KS K 0594 method of PET breathable fabric was superior than that of nylon one, in addition, water vapor permeability of coated or laminated breathable fabrics were higher than those of hot melt or dot laminated fabrics. The water vapor permeability of breathable fabric was dependent on the thickness, weight and density, which was consistent with measuring method. However, water vapor permeability according to materials and finishing method showed different results according to measuring method. The correlation coefficient of WVP of PET breathable fabrics between ISO and KS K measuring methods was -0.83 and the correlation coefficient of WVP of coated breathable fabrics was -0.72 and -0.71 for KS K and ASTM and -0.72 for KS K and ISO in hot melt laminated breathable fabrics. According to regression analysis, WVP of PET breathable fabric by both KSK and ISO measuring methods was highly dependent upon on the density and weight. In addition, WVP of hot melt laminated breathable fabric was highly dependent upon thickness, weight and density. Therefore, relevant measuring method for WVP of breathable fabrics has to be adopted to measure precise breathability.

• 대한기계학회논문집A
• /
• 제27권8호
• /
• pp.1338-1346
• /
• 2003

Three-dimensional formability of the thermoplastic laminar composite was studied according to manufacturing conditions. Five different types of the plain weave fabric were used as reinforcement with PET matrix. The square blank was made by press consolidation technique and formed in the type hemisphere. B-factor defined as the ratio of width of yarn and distance between yarns was used as the factor of formability in the type of plain weave fabric. The formability of PET/Glass fabric laminar composite was estimated in terms of forming rate and B-factor with the thickness distribution, area ratio of blank, and intra-ply shear angle. The thickness distribution across hemisphere was strongly affected by the B-factor, forming rate and blank thickness. The area ratio of blank was increased with B-factor, forming rate and blank thickness. Also, it was found that the intra-ply shear angle depends on the B-factor and forming rate.

• 한국의류학회지
• /
• 제25권7호
• /
• pp.1193-1202
• /
• 2001

The goal of this research is to investigate the effect of fusible interlinings on the mechanical characteristics and appearance related values for the Lyocell fabrics. In this study, to establish optimum fusing conditions, peel strength of the fused fabrics depending on the fusing temperature, pressure and time was measured. Appearance related properties and mechanical characteristics of the fused fabrics ere determined. The reulst are as follows: In the fusing condition of $120^{\circ}C,\;3kgf/textrm{cm}^2$, 15sec, peel strength was excellent. Peel strength was excellent in the case of tencel/cotton fabric, with increasing cover factor of woven interlining, with twill and nonwoven interlining. Flex stiffness was increased in the case of tencel/cotton fabric, with increasing weight of woven interlining, with twill and nonwoven interlining. Drapability was excellent in the case of 100% tencel fabric, with decreasing weight of woven interlining, with plain and woven interlining. Crease recovery was excellent in the case of 100% tencel fabric, with increasing weight of woven interlining, with twill and woven interlining. Shear and bend properties were increased in the case of tencel/cotton fabric, with increasing weight of woven interlining, with plain and nonwoven interlining.

• 한국염색가공학회지
• /
• 제30권1호
• /
• pp.38-50
• /
• 2018

This investigation reported the recent development of 3 dimensional fabrics such as spacer fabric, 3 dimensional multi-layered fabric and 3 dimensional braided fabric. First, we categorized 3 dimensional fabrics into 3 main products; 3 dimensional woven fabrics, 3 dimensional knitted fabrics and 3 dimensional braided fabrics with reviewing the possible main applications. We also reported the research and development trends of 3 dimensional fabrics by analyzing technical trends in industry and research institutes at domestic and overseas. United State, Germany and Japan lead the manufacturing technology for the mainly preform related products to apply in aerospace, automotive, protections, architecture and clothing applications. Lastly, we reviewed the main products of the leading company which manufactured using the 3 dimensional fabrics.

• 한국의류학회지
• /
• 제27권9_10호
• /
• pp.1153-1159
• /
• 2003

The effects of changing aqueous solution properties by nonionic surfactants on wetting behavior and water retention properies of hydrophobic PET (polyethylene terephthalate) fabric were reported. The aqueous solution properties were diversified by mixing and diluting two nonionic surfactants, i.e., sorbitan monolaurate (Span 20) and polyoxyethylene(20) sorbitan monolaurate (Tween 20). The surface wetting properties ($cos{\theta}$) of PET fabric were greatly improved by adding $10^{-1}g/dl$ Tween 20 and further improved by mixing Span 20 to the system. The water retention properties (W) of PET fabric were also greatly increased by addition of $10^{-1}g/dl$ Tween 20. In diluted surfactant systems, the $cos{\theta}'s$ were increased with decreasing surface tension of aqueous liquids. The ratios of aqueous liquid retained in the pore structure to liquid retention capacity (W/H) were also increased with decreasing surface tension, however, W/H values were dramatically increased right after critical micelle concentration (cmc). The existence of micelles was important for the retention of aqueous liquids in the fabric. The critical surface tension of PET fabric used was found to be 28.7dyne/cm.

• 한국염색가공학회지
• /
• 제6권3호
• /
• pp.8-14
• /
• 1994

A new flame retardant diphenyl butylamidophosphate (DPBAP) for PET fabric was synthesized and its flame retardancy was examined. The results have shown that PET fabrics treated by DPBAP(with DPBAP and on 4-10 %) show excellent flame retardancy. Since the DPBAP treated PET fabric show essentially no change in the drape stiffness and the tensile strength, it is believed that DPBAP is chemically stable in PET fabric. In addition to this, the washing fastness of DPBAP on PET fabric tested by the 5 times of water washing method also appeared to be excellent. Judging from the fact that DPBAP was synthesized from relatively cheap material as well as the above cited DPBAP properties as a good flame retardant, the potential of DPBAP to be developed as a commercial flame retardant for PET fabric seems to be high.

• 한국염색가공학회지
• /
• 제27권4호
• /
• pp.309-317
• /
• 2015

This study is the high contraction processing conditions set by the method of the CPB process. And the ultimate goal of this study is the high contraction of the CPB processing test method that can solve the problems of the high-contraction fabric processing method of the current jet dyeing machine. Non-coating process(CPB process) developed by the expression of a soft touch, light weight, functional and to develop excellent breathable nylon fabric. The nylon fabrics established the optimum processing conditions through the high contraction of the various test conditions, the CPB system.(The benzyl alcohol was used as the main constrictor.) At this time, the warp and weft contraction of nylon fabric was about 20%. And it established the constrictor concentration, the treatment temperature, time of a variety of tests. Also non-coating process(CPB process) can develop soft touch, lightweight, excellent air permeability. As a result, we developed a high contraction nylon fabric having a uniform surface. Manufactured fabric is used for Wind-proof and Down-proof.