• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1-6
• /
• 2008

When a saturated clay is sampled in an undisturbed manner from a bore hole, the sample extends vertically and shrinks horizontally under undrained conditions due to stress release. The conventional consolidation test specimen is trimmed from the expanded sample so that its diameter is equal to the inner diameter of the consolidation test ring, this test procedure does not reproduce the actual consolidation behavior. The measurement of sample extension was conducted by means of overcoring method found that the extension strains were 1 to 2%. To simulate the in-situ consolidation behavior, the consolidation test method that uses a specimen with a slightly smaller diameter than the inside diameter of consolidometer so that the specimen expands laterally to the inside of the ring.

• 한국물환경학회지
• /
• 제20권6호
• /
• pp.664-669
• /
• 2004

An upflow BAF(Biological Aerated Filter) equipped with an expanded clay media was applied to reuse weaving wastewater of water jet loom. The performance of lab-scale biofilter was investigated by the adjustment of EBCTs(Empty Bed Contact Time) and the packing ratio of media, which were changed 1.1 to 3.7hr and 38 to 63%, respectively. In most conditions except 1.1hr of EBCT, BOD, CODcr, SS and Turbidity of the effluent were 1~4mg/L, 7~16mg/L, 1~5mg/L and 5~14NTU, where their removal efficiencies were 76~95%, 82~93%, 63~94% and 59~81%, respectively. From the observation of SEM(Scanning Electron Microscope) photographs of porous clay media, it was revealed that this media provided good performance of retaining microbes effectively. In addition, $0.44~0.49kgVSS/kgBOD_{rem}$. of low sludge reduction was expected. The most efficient back washing cycle and procedure were once per 4 to 9 days and air including collapse-pulsing method, respectively. Therefore, this system can be of use as an weaving wastewater treatment for reuse.

• 한국농공학회지
• /
• 제39권3호
• /
• pp.128-137
• /
• 1997

In this study, examined influence of consolidation effect that had affected by location of pump inlet that was set collection well for drainage of pore water discharged by embankment on soft ground through the field test. The results of this study are summarized as follows; 1 Initial consolidation curve value were larger than theoritic value, the cause of these phenomena were thought influence of secondary consolidation and three dimensional strain of soft clay. 2. The settlement value of Hosino method was larger than that of Hyperbolic method, but settlement value of Hyperbolic method was accurate more than that of Hosino method in the prediction of settlement. 3. When pump inlet in collection well came down from GL+O.3m to GL-1.5m, settlement value increased about 10cm and when the ground water level was made insitu after pumping had completed , settlement was expanded about 7~8cm. So it is found that location change of pump inlet bad an influence on settlement remarkably. 4. If location of pump inlet in collection well for large scale estate or wide road site is lowered than original ground level, the settlement will be accelerated effectively, and at this stage automatic pump must be used in pumping.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1991년도 봄 학술발표회 논문집
• /
• pp.99-104
• /
• 1991

It is necessary to generalize the use for structural ALA Concrete in our country, as increasing in the need for the development of ALA and the use of ALA Concrete which is related with the diminution of the self load and foundation section of structure responding to the realistic requirement against the decrease of natural aggregate and the high-rising and large-sizing of structures. This little study, therefore intended to help in the mixing design of concrete by considering the fundamental properties of ALA Concrete used with expanded clay, which is considered by acopting the experimental factors such as unit cement content, water cement ratio and the rate of fine aggregate. By considering the results of this experiment, it has difficulty in getting expected slump with the unit water content of normal concrete because of the large absorption of lightweight aggregate, and because the weight of unit volume and specific gravity ALA Concrete are small it appears that the strength and Elastic Modulus of that are small too and that it is more ductile than normal concrete.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.832-839
• /
• 2010

The pulse discharge anchor is a method to increase the capacity of anchors using electric discharge geotechnical technologies, which is also known as pulse discharge and electric-spark technologies. The pulse discharge anchor has bulbed bond length that is expanded by high voltage electrokinetic pulse energy. 24 anchors were installed in the weathered soil and sandy clay at the Geotechnical Experimentation Site at Sungkyunkwan University in Suwon, Korea and attached strain gauge at 10 anchors. The numerical predictions by Beam-Column analysis were compared with observed measurements in a field load test.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.846-851
• /
• 2003

This study was performed to develop the lightweight polymer concrete using expanded clay and perlite to improve workability, durability and chemical resistance for bottom draining structure under severe condition. This paper was composed of two parts. One is to invest the physical and mechanical properties of lightweight polymer concrete using synthetic lightweight aggregate, the other is to the develop products for bottom draining structure. Physical and mechanical test for lightweight polymer concrete was performed unit weight, compressive and flexural strength, chemical resistance, accelerated weathering test, absorption ratio and optimum mix for lightweight polymer concrete was designed. Also, products for bottom draining structures by optimum mix of lightweight polymer concrete was made draining trench of small size.

• 한국세라믹학회지
• /
• 제41권1호
• /
• pp.81-85
• /
• 2004

점토를 이용한 나노 다공성 촉매 제조를 목적으로 $Ni^{2+}$ 이온으로 피복된 $SiO_2$ 나노 졸 입자를 2차원 충상점토 화합물의 층간에 삽입, 가교화 시켜 비표면적 및 다공도가 우수한 $NiO-SiO_2$ 가교화 점토($NiO-SiO_2$-PILM)를 합성하였다. 나노 크기의 실리카 졸 입자는 tetraethyl orthosilicate(TEOS)를 가수분해하여 합성하였고, 여기에 $Ni^{2+}$ 수용액을 첨가한 다음 NaOH 용액을 적정하여 $Ni^{2+}-SiO_2$ 혼합 나노 졸입자를 완성하였다. 이렇게 제조된 혼합 졸 용액을 1wt%의 점토 수분산액에 첨가하여 $60{\circ}C$에서 5h 이온교환 반응을 통해 층간에 삽입, 수세, 건조 후 $40^{\circ}C$에서 2시간 열처리 하므로써 다공성 가교화 점토를 제조하였다. 나노 졸 입자의 가교화에 따라 점토의 층간거리($d_{001}$)는 $45{\AA}$ 정도 크게 증가하였고 $600^{\circ}C$까지도 다공구조가 안정하게 유지되었다. 또한 질소 흡착-탈착 등온선 분석 결과 비표면적($S_{BET}$)이 최대 $760m^2/g$으로 다공 구조가 매우 잘 발달되어 있음을 확인하였고, $NiO-SiO_2$ 졸 가교화 점토의 경우 $NiO-SiO_2$ 나노입자가 층간에 이중층으로 배열되어 있음을 알 수 있었다.

• 농업과학연구
• /
• 제23권1호
• /
• pp.120-130
• /
• 1996

본 연구는 세골재는 사용하지 않고 인공경량조골재로써 팽창점토와 경석을 사용하여 제작된 인공경량골재 콘크리트의 응력-변형율특성을 구명하기 위하여 실시되었으며, 시험을 통하여 얻어진 결과를 요약하면 다음과 같다. 1. 동탄성계수는 인공경량조골재인 팽창점토와 경석을 사용한 경우 $1.9{\times}10^5kg/cm^2$과 $2.0{\times}10^5kg/cm^2$으로 나타났으며, 경석을 사용한 경우가 5%정도 크게 나타났다. 2. 정탄성계수는 팽창점토 및 경석을 사용한 경우 $1.8{\times}10^5kg/cm^2$과 $1.6{\times}10^5kg/cm^2$으로 나타났으며, 정탄성계수는 동탄성계수보다 10~30%정도 작게 나타났다. 3. 사용골재에 따른 하중-이력곡선은 하중이 증가하여 최대하중에서 파괴가 이루어진 후 급격히 감소하는 경향을 보였으며, 특히 기포제를 첨가한 경우는 최대하중에서 파괴된 이후에도 상당시간 내하능력을 유지하는 것으로 나타났다. 4. 응력-변형율곡선은 사용골재의 종류에 관계없이 응력의 증가와 함께 증가하여 최대하중에서 파괴가 된 후 급격히 감소하는 경향을 보였으며, 취성이 크다는 것을 알 수 있었다. 5. 최대응력하에서의 변형율은 팽창점토를 사용한 경우 $1.7{\times}10^{-3}$, 경석을 사용한 경우는 $2.83{\times}10^{-3}$로써, 팽창점토보다 경석을 사용한 경우의 변형율이 66%정도 크게 나타났다.

• 대한토목학회논문집
• /
• 제42권6호
• /
• pp.787-792
• /
• 2022

겨울철 제설염의 사용은 콘크리트의 미세조직을 손상시기게 되고 이는 내구성을 감소시켜 콘크리트의 수명 단축으로 이어진다. 이러한 단점을 개선하기 위해 상변화물질(Phase Change Material, PCM)의 잠열을 콘크리트에 적용함으로써 손상을 완화하고 제설염의 수요를 감소시킬 수 있는 융설 PCM 함침 경량골재(Phase Change Material Impregnated Light Weight Aggregate, PCM-LWA) 콘크리트를 개발하고자 한다. 콘크리트를 제작할 때, PCM을 함침하고 캡슐화한 팽창점토(Expanded Clay)는 일반골재의 50 %를 대체하여 사용되었으며, 열적 성능을 향상시키기 위해 사용된 다중벽 탄소나노튜브(Multi-walled Carbon Nano Tube, MWCNT)는 바인더 중량 대비 0.10 %, 0.15 % 및 0.20 %의 비율로 첨가되었다. PCM-LWA를 적용한 시편들의 압축강도 시험 결과 약 54 %의 강도 감소를 보였지만 MWCNT의 첨가를 통하여 PCM-LWA 콘크리트의 열적 성능을 크게 향상시켰다. 열 사이클링 시험에서 모든 시편은 15℃ ~ -5℃의 온도에서 시험하였다. 주변 온도가 0℃ 미만으로 내려갈 때, 다른 시편들의 내부 온도는 0℃ 미만으로 내려가거나 조금 웃도는 경향을 보였지만, CNT를 0.10 % 첨가한 시편의 내부 온도는 2℃로 유의미한 차이를 보였다. 0.15CNT와 0.20CNT의 경우 CNT의 함유로 인하여 과냉각이 발생하였고 열효율이 떨어지게 되어 시편 내부의 온도가 0℃ 이하로 떨어지는 것을 확인할 수 있었다. 융설 시험에서 열 사이클링 시험의 결과와 유사하게 50PCM-LWA와 0.10CNT는 얼음을 녹이는 데에 가장 뛰어난 성능을 보였지만 시간이 흐름에 따라 열전도율이 높은 0.10CNT 시편이 가장 우수한 성능을 보였다.

• Wind and Structures
• /
• 제26권2호
• /
• pp.75-87
• /
• 2018

A large number of low-rise buildings experienced serious roof covering failures under strong wind while few suffered structural damage. Clay and concrete tiles are two main kinds of roof covering. For the tile roof system, few researches were carried out based on Finite Element (FE) analysis due to the difficulty in the simulation of the interface between the tiles and the roof sheathing (the bonding materials, foam or mortar). In this paper, the FE analysis of a single clay or concrete tile with foam-set or mortar-set were built with the interface simulated by the equivalent nonlinear springs based on the mechanical uplift and displacement tests, and they were expanded into the whole roof. A detailed wind tunnel test was carried out at Tongji University to acquire the wind loads on these two kinds of roof tiles, and then the test data were fed into the FE analysis. For the purpose of validation and calibration, the results of FE analysis were compared with the full-scale performance ofthe tile roofs under simulated strong wind impact through one-of-a-kind Wall of Wind (WoW) apparatus at Florida International University. The results are consistent with the WoW test that the roof of concrete tiles with mortar-set provided the highest resistance, and the material defects or improper construction practices are the key factors to induce the roof tiles' failure. Meanwhile, the staggered setting of concrete tiles would help develop an interlocking mechanism between the tiles and increase their resistance.