• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.55-60
• /
• 2004

Residual gas acts as a diluent which results in reducing the in-cylinder temperature as well as the flame speed, significantly affecting fuel economy, NOx emissions and combustion stability. Therefore it is important to determine the residual gas fraction as a function of the engine operating parameters accurately. However, the determination of the residual gas fraction is very sophisticated due to the unsteady state of induction and exhaust process. There has been little work toward the development of a generally applicable model for quantitative predictions of residual gas fraction. In this paper, a simple model for calculating the residual gas fraction in SI engines was suggested. The amount of fresh air was evaluated through AFR and fuel consumption. After this, from the intake temperature and pressure, the amount of total cylinder-charging gas was estimated. The residual gas fraction was derived by comparing the total charging and fresh air. This results coincide with measured EGR value very well.

• 동력기계공학회지
• /
• 제3권3호
• /
• pp.44-53
• /
• 1999

This study is concerned with the emission characteristics of kerosene fan heater, which is burned with kerosene and water droplets simultaneously in the burner, in order to prohibit the emissions of harmful exhaust gas and reduce smell caused by incomplete combustion, and the addition of water droplets to the conventional kerosene fan heater was performed by ultrasonic atomizer. For the investigation of this study, the measurement of exhaust gas components and exhaust gas temperature was carried out by using an automatic combustion gas analyser and $NO_x$ analyser, and the measurement of consumption weight of oil and water was obtained by using electric digital balance. Consequently, according as the water percent weight ratio of about $21{\sim}23%$ was supplied for this study, it was found that the combustion-generated $NO_x$ and CO emissions were reduced very largely, but the emissions of $O_2\;and\;CO_2$ and the temperature of exhaust gas were not changed.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2001년도 제22회 KOSCI SYMPOSIUM 논문집
• /
• pp.139-146
• /
• 2001

The experimental study was carried out for the diffusion flame characteristics of second stage combustor with the variations of temperature and supplying rate of hot exhaust gas from first stage combustor. It also examined the flame structure and NOx formation of the second stage combustor in which the fuel(natural gas) is supplying into the mixture of oxygen hot exhaust gas from first stage combustor. The results show that the increasement of temperature and flow rate of exhaust gas lead to increase the NOx up to 30ppm with 19% $O_2$ condition

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권3호
• /
• pp.398-404
• /
• 1999

The EGR is needed for one of various strategies to reduce NOx emission. But to get the proper EGR rate the intake and exhaust system become complicated. That is a reason why we consider using the built0in EGR system. The built-in EGR is a system which reduces Nox by controling the residual gas fraction in cylinder by changing valve timing and valve lift of intake and exhaust. In this paper characteristics of volumetric efficiency and residual gas fraction in cylinder were investigated for various engine speeds by changing valve timing and valve lift of intake and exhaust. In this paper characteristics of volumetric efficiency and residual gas fraction in cylinder were investigated for various engine speeds by changing valve timing and valve lift of intake and exhaust in the 4 stroke-cycle diesel engine. Volumetric efficiency and residual gas fraction were calculated by the method of characteristics. As the results the possibility of suing the built-in EGR system was confirmed.

• 한국주거학회:학술대회논문집
• /
• 한국주거학회 2001년도 학술발표대회논문집
• /
• pp.77-82
• /
• 2001

This paper is contents that measure the ventilation rates and temperature by driving condition of exhaust fan, vapor, contaminant occurrence amount of carbon dioxide etc. In kitchen of apartment house. The ventilation rates in the apartment kitchen measured by Tracer Gas Method. And, temperature of when cook by gas table hood lower part 10cm and floor upside 10cm of kitchen central part, 120cm, 210cm heights measure. As ventilation rates measurement result, ventilation number of times was 0.7(number of times/hour) when did not to operate exhaust fan. but we were measured by 2.3(number of times/hour) when drove strongly. As temperature measurement result at cooking by gas table, temperature showed highest in hood lower part 10cm of case that do not operate exhaust fan. Temperature at kitchen central was most low in 10cm height in talc floor, and 210cm were measured highest. Concentration of carbon dioxide is very high by 4,350ppm after measurement time 10 minutes in state who do not operate exhaust fan at cooking by gas table.

• 한국해양환경ㆍ에너지학회지
• /
• 제4권4호
• /
• pp.42-50
• /
• 2001

본 논문에서는 수출입컨테이너 화물의 육상운송에서 연안운송으로의 전환을 이용한 CO₂가스 및 배기가스 배출량 삭감이 제안되어진다. 먼저 국내의 CO₂가스 배출량, 배기가스 배출량, 수출입컨테이너화물의 물동량 등에 대하여 간단히 살펴본다. 또한 경인지역과 부산항사이의 수출입컨테이너화물 수송에 대하여 육상운송에서 연안운송으로의 변환에 의한 CO₂가스 및 배기가스 배출량 삭감효과에 대하여 고찰한다. 마지막으로 연안운송의 분담율 변화와 320TEU 소형컨테이너선 이용에 따른 NOx가스 배출량 변화를 고찰한다. 본 연구의 결과 육상운송에서 연안운송으로의 전환이 CO₂가스 및 배기가스 배출량 삭감에 효과적인 것을 확인하였다.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2008년도 춘계학술 발표회
• /
• pp.217-222
• /
• 2008

In the last five years, 45 people died and 104 were wounded because of carbon monoxide poisoning accident. CO poisoning accident is higher than any other gas accident in the rate of deaths/incidents. Most of these CO poisoning accidents were caused by defective exhaust tube in the old gas boiler and multi-use facility. In this study, the spread of CO gas released from leakage hole of exhaust tube was analyzed by concentration measuring test. CO gas leaked form exhaust tube in a building was highest concentrated near the ceiling. Through these experiments, the reasonable installation location of CO alarm was made certain and suggested.

• 에너지공학
• /
• 제23권3호
• /
• pp.51-57
• /
• 2014

MILD 연소는 고온의 배기가스가 연소로 내에 유입되는 연료와 공기의 혼합물과 고온의 배기가스 가 만나는 위치에 따라 질소산화물 저감 특성이 많은 영향을 받는다. 본 연구에서는 폐기물소각로에 적용한 MILD 연소로에서 배기가스 재순환 여부에 따른 유동 특성과 배기가스 재순환 위치에 따른 유동 특성을 살펴보아 최적의 배기가스 재순환 위치를 선정하는 것을 목적으로 하였다. 본 연구의 전산 해석의 결과는 배기가스 재순환이 없는 경우에는 수직 격벽 상부의 단면에서 속도 분포는 수직 격벽 바로 상부에 큰 속도가 있고 더 상부는 역류가 일어나는 것을 확인할 수 있었다. 배기가스 재순환이 있는 경우는 상부 자유공간에서의 유동 균일도를 수직 격벽 상부 단면에서의 x 방향 속도의 %RMS 값으로 비교하였으며 재순환 흡입구 위치가 자유공간 우측 상단에 위치한 경우가 %RMS 값이 57.4%로 가장 작은 값을 가지며 따라서 가장 효과적임을 알 수 있었다.

• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.123-131
• /
• 1999

Natural gas is one of the most promising alternative fuels for automotive vehicles. However, natural gas varies in compositional between the originating fields and may be further modified due to processing and additional mixing. These variations are known to affect engine performance and emissions through changes in fuel metering and combustion characteristics. In the present study, the effect of gas compositions on vehicle performance such as fuel economy, driveability and exhaust emissions was examined. Analysis are made of using 3 types of NGVs which were made by automakers and 6 different fuels which are selected in consideration of the variation in fuel composition on the worldwide market. The results may be utilized to develop natural gas natural gas engine in automaekrs and/or to establish the fuel standard in the refueling stations.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2868-2873
• /
• 2008

Carbon Monoxide(CO) poisoning accident is higher than any other gas accident in the rate of deaths/incidents. In the last five years, 36 people died and 104 were wounded because of carbon monoxide poisoning accident. Most of these CO poisoning accidents were caused by defective exhaust tube in the old gas boiler and multi-use facility. In this study, the spread of incomplete combustion gas(CO) released from leakage hole of exhaust tube was analyzed by computational flow modeling and concentration measuring test. CO gas leaked form exhaust tube in a building was highest concentrated near the ceiling and formed the circular currents along the walls. Through these experiments and simulation, the reasonable installation location of carbon monoxide alarm was made certain and suggested.