• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.3
• /
• pp.328-335
• /
• 2009

This study was undertaken to investigate the influence of exposure and removal of four different cryoprotectants (CPAs) on the ATP content of cumulus cell-enclosed (COs) and cumulus cell-denuded (DOs) immature porcine oocytes. The in vitro nuclear maturation of the COs, exposed to and removed from the CPAs was also assessed. Both COs and DOs were exposed to 1.5 M concentrations of each CPA (ethylene glycol (EG); propylene glycol (PG); dimethyl-sulfoxide (DMSO); and glycerol (G)) for durations of 5, 15, and 30 minutes at room temperature ($23.5{\pm}1.5^{\circ}C$), and immersed in physiological saline supplemented with 20% (v/v) fetal bovine serum for 5 minutes ($39^{\circ}C$) to remove each CPA. Before, during and after exposure to each CPA, the ATP content of both the COs and the DOs was measured. After removal from each CPA an aliquot of the COs was matured for 44${\pm}$2 h, and their nuclear maturation rates were measured up to the metaphase stage of the second meiotic division (the M-II stage). The maturation rates up to the M-II stage were not significantly different between all the groups that were exposed to each CPA for 5 minutes. For 15 and 30 minute exposures, the maturation rates of the COs exposed to PG, DMSO and EG were almost the same as those of the control groups; however, the rates of G group exposed for 15 and 30 minutes were significantly lower (p<0.05) than the control group. These groups were also found to have a decrease in the ATP content of COs and DOs during and after exposure for the same periods (p<0.05). In addition, although the ATP contents of the COs after exposure to EG for any period were the same as the controls, the ATP content of the DOs exposed to EG for any period were significantly lower (p<0.05) than those of the controls. When the ATP content of the COs and DOs of each CPA were compared, the DOs exposed to PG were found to have a significantly greater level (p<0.05) than DOs exposed to G for any duration. In addition, the ATP content of DOs exposed to PG for 30 min and removal was also higher (p<0.05) than when exposed to DMSO for the same period. These findings indicate that PG may be a useful CPA for the cryopreservation of immature porcine oocytes.

• Journal of Soil and Groundwater Environment
• /
• v.12 no.2
• /
• pp.65-71
• /
• 2007

This study has been focused on an application of microwave pre-treatment of soil contaminated with volatile organic chemicals, and BTEX(benzene, toluene, ethylene, xylene). Microwave experiments were carried out under different power conditions (2 kW, 4 kW) using different moisture contents and BTEX concentration. According to these results of this study, the most BTEX removal efficiency was with 20% moisture contents regardless of electric power. The result show that 2kW was determined to the optimum electric power at $10{\sim}30%$ moisture contents, but the optimum power was 4 kW at 50% of moisture content.

• Journal of Korean Society for Atmospheric Environment
• /
• v.23 no.6
• /
• pp.699-707
• /
• 2007

This study was carried out to investigate the reaction characteristics of corona/catalyst hybrid $DeNO_x$ process. The experiments were performed by using the multi-staged pin-to-hole type corona reactor which is enable to control the pin-to-hole gap and to insert the catalyst. Also, used for this study, were catalysts which commercially used Pt, Pd and $TiO_2$, and oxygen and hydrocarbon ($C_2H_4$) as reagents. In the syn-gas test, at high temperatures in the range of $100{\sim}200^{\circ}C$, the corona-only $DeNO_x$ process did not reduce the $NO_x$ concentration effectively. However in the presence of ethylene and oxygen as reagents, the $NO_x$ removal efficiency was better at these high temperatures than corona-only $DeNO_x$ process. In addition, coronal catalyst hybrid process with $TiO_2$ showed more efficiency of $NO_x$ removal than Pt and Pd catalyst, because the $TiO_2$ catalyst was more active than Pt and Pd catalyst to converse the $NO_2$ to $HNO_3$. Furthermore, at the condition of real diesel exhaust gas, the $DeNO_x$ efficiency of corona/catalyst hybrid process was not good at higher reaction temperature and plasma density.

• Journal of Soil and Groundwater Environment
• /
• v.19 no.3
• /
• pp.94-103
• /
• 2014

In this study washing efficiency and desorption isotherms for heavy petroleum oil (HPO), Zn, and Pb bound to complex contaminated soils were examined using various soil flushing agents. Sodium dodecyl sulfate (SDS), methanol, ethylene diamine tetraacetic acid (EDTA), and citric acid were selected as soil flushing agents. 3% (w/v) and 4% SDS showed the highest removal efficiency for HPO, but the difference was not statistically significant (p > 0.05). Thus, 3% SDS was chosen as the best soil flushing agent for HPO. In the case of heavy metals, 0.1-M EDTA showed the highest removal efficiencies. But 0.05-M citric acid was selected due to its economic and eco-friendly strengths. The desorption isotherms obtained using Freundlich and Langmuir models indicated that the maximum desorption characteristics ($K_F$ and $Q_{max}$) of HPO with 4% SDS and 90% methanol and heavy metals with 0.1-M EDTA and 0.1-M citric acid, respectively, were markedly lower than in other cases. In addition, when 4% SDS and 90% methanol were used for HPO in the range of $C_e$ higher than 600 mg/L, and when 0.1M citric acid and 0.1M EDTA were used for Zn and Pb in the range of $C_e$ higher than 300 and 100 mg/L, respectively, the distribution constant converged to certain levels. Thus, constant values of $K_U$ and $K_L$ were determined. It was found that these constants represent the maximum desorption capacity and they can be used as distribution coefficients of desorption equilibrium for the flushing agents. The results of this study provided fundamental information for the selection of the best agents as well as for the process design and operation of soil washing/soil flushing of complex contaminated soils.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.13 no.1
• /
• pp.45-50
• /
• 2006

Papers were prepared from cut cocoons and mulberry branches, which are byproducts from sericulture industry. The long filament of silk should be cut into appropriate length in order to prepare paper and this was achieved by chemical method. By a mixture of sodium hydroxide and sodium carbonate solution, the silk filaments were cut into short fibers (less than 1 mm in length). Since the short silk fibers (sSf) could not bind each other by itself, starch and poly(ethylene oxide)(PEO) were added as a bonding agent. When starch and PEO were used in a ratio of 3:7, the silk papers had optimum mechanical properties for paper. Fibers from the skin of mulberry branches (MBF) were added to sSf to enhance the mechanical properties of pure silk paper. Bleaching of MBF was performed with a mixture of hydrogen peroxide and sodium silicate. The mechanical properties were greatly enhanced and the optimum blend ratio of MBF and sSf were 7:3. The mulberry/silk paper has good absorption property against formaldehyde, and therefore, the paper could be applied as a wall paper for preventing the sick house syndrome.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.9
• /
• pp.32-37
• /
• 2008

Freestanding hydride vapor phase epitaxy grown GaN(Gallium Nitride) substrates subjected to various polishing methods were characterized for their surface and subsurface conditions, Although CMP(Chemical Mechanical Polishing) is one of the best approaches for reducing scratches and subsurface damages, the removal rate of Ga-polar surface in CMP is insignificant($0.1{\sim}0.3{\mu}m$/hr) as compared with that of N-polar surface, Therefore, conventional MP(Mechanical Polishing) is commonly used in the GaN substrate fabrication process, MP of (0001) surface of GaN has been demonstrated using diamond slurries with different abrasive sizes, Diamond abrasives of size ranging from 30nm to 100nm were dispersed in ethylene glycol solutions and mineral oil solutions, respectively. Significant change in the surface roughness ($R_a$ 0.15nm) and scratch-free surface were obtained by diamond slurry of 30nm in mean abrasive size dispersed in mineral oil solutions. However, MP process introduced subsurface damages confirmed by TEM (Transmission Electronic Microscope) and PL(Photo-Luminescence) analysis.

• Journal of Conservation Science
• /
• v.25 no.4
• /
• pp.421-430
• /
• 2009

This research was carried out focusing on the urgent treatment and related studies for paint scribbling on Samjeondobi Monument (Historic Sites No. 101) in 2007. Before the preliminary test, the paint lacquer used on the surface of Samjeondobi Monument was analyzed. The paint lacquer turned out to be the paint lacquer spray composed of $Pb_3O_4$ used for the red pigment in the market. It was proved that the poultice used with the organic solvent was the best way to remove the paint pollutants following the preliminary test for the removal of paint pollutants which was performed with various removal methods by the laser, etc. However, the removing the paint pollutants was found in difficulty in contrast to the preliminary tests because the paint on the spot was hardened so rapidly over time that there was difference from the situation of the laboratory. For that problem, the poultice method with ethylene dichloride of main component from Remover (goods in the market) was the most efficient, therefore the pollutants were removed with the solution of alkyds resin and nitrocellulose and the rest part was removed by the $Laponite^{(R)}$ RD.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.10
• /
• pp.1072-1080
• /
• 2005

The extraction characteristics of heavy metals(HM) from a contaminated soil at existing lead smelters were investigated with ethylene diamine tetraacetic acid(EDTA), citrate and HCl as washing solutions. EDTA was more effective for Pb than for other heavy metals. As the mol ratio of EDTA/HM increased, the removal efficiency of heavy metals became higher. When the mol ratio of EDTA/HM approached to 6.5, it removed Pb most effectively. Citrate was effective especially in extracting Zn. The removal efficiency of HCl was comparatively high in almost all heavy metals, and at 0.3N concentration it was the highest. After soil washing process by the use of EDTA, the great part of exchangeable fractions and most of heavy metals of weakly adsorbed like carbonate fraction were extracted. For washing with citrate and HCl, four heavy metals showed the similar exchange of chemical partitioning and the exchangeable fractions of Pb which has weakly adsorbed to soil were more increased than before the process. As removal efficiency of citrate washing process depends upon the distribution of non-detrital fractions, so it can be contended that only the amount of non-detrital fractions could be removed from all the heavy metal content. EDTA and HCl could remove most of non-residual fractions in all heavy metals except Zn. As a result of EDTA washing, toxicity characteristic leaching procedure(TCLP) concentration of the processed soil met the USEPA Pb limit of 5.0 mg/L.

• Korean Journal of Heritage: History & Science
• /
• v.40
• /
• pp.413-430
• /
• 2007

This study analyzed the foreign substances in waterlogged archaeological woods and compounds in soil where waterlogged archaeological wood was buried, in order to examine the relationship between burial environment and foreign substances in waterlogged archaeological wood. The XRF(X-ray Fluorescence Spectroscopy) and EDX(Energy Dispersive X-ray) analysis were conducted to examine the effect of iron(Fe) to blacken the waterlogged wood. The XRF results showed that investigated soil contained Si, Al, and Fe. Wood ash contained more sulfur and Fe than any other elements in the EDX analysis. Cellulose and hemicellulose were significantly reduced at the surface of wood, which is the blackened part of waterlogged wood. Foreign substances changed the surface color. These problems could be solved by removal of foreign substances in waterlogged archaeological wood using EDTA(Ethylene Diamine Tetra Acetic acid). The optimum condition to remove Fe from waterlogged wood by EDTA was investigated. To do this, the concentration of Fe removed was measured with various concentration of EDTA-2Na. The optimum pH of EDTA-2Na was figured to be 4.1 to 4.3. As the concentration of EDTA increased, the extracted concentration of Fe also increased. In the case of 0.4 wt% of EDTA-2Na, about 60ppm of Fe was eliminated and was stabilized after 48 hours. In the case of EDTA-3Na, the optimum pH was 7 to 8, and about 10 ppm of Fe was eliminated at 0.4 wt% of EDTA-3Na. In the case of EDTA-4Na, the optimum pH was 10 to 11, and about 20 ppm of Fe was eliminated at 0.4 wt% of EDTA-4Na. In conclusion, the iron(Fe) in waterlogged archaeological wood was removed by EDTA treatment and it increased the whiteness of the surface.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.45 no.2
• /
• pp.199-208
• /
• 2019

This study reports water-resistant oil-in-water (O/W) emulsion-based sunscreening formulations prepared using a poly(ethylene glycol)-poly(${\varepsilon}$-caprolactone)-poly(ethylene glycol) (PEG-PCL-PEG) triblock polymeric surfactant. As a result of a variety of outdoor recreational activities such as swimming and hiking, consumer needs for development of advanced water-resistant sunscreen formulations are increasing. Water-resistant sunscreens are mostly based on water-in-oil (W/O) emulsions, because they should not be wiped off by water or sweat. However, the W/O emulsion formulations have a disadvantage in that the feeling of use is oily and difficult to remove. On the other hand, the O/W emulsion formulations are excellent in achieving the better skin feel as well as the easier removal. However, it is difficult to provide the O/W emulsion formulations with the water-repelling performance, since re-emulsification likely occurs upon getting touch with water. To solve this problem, this study proposes a O/W emulsion-based sunscreen formulation, a triblock polymeric surfactant having relatively high interfacial tension HLB value (~ 10). This allows the sunscreen formulations to exhibit the improved water repellence function by preventing their re-emulsification. The sunscreen formation system prepared in this study would be useful for diversification of functional sunscreen products, taking advantages of its excellent emulsion stability, UV protection performance, long lasting water-resistant function and selective cleansing effect with only foam cleanser.