• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.1
• /
• pp.93-101
• /
• 2010

Reverse osmosis (RO) membranes have been widely used for desalination as well as water and wastewater treatment facilities. Cleaning process is important to maintain stable operation as well as prevention of membrane fouling. Purpose of this research is to analyze electrostatistic and chemical characteristics after cleaning of RO membrane against $SiO_2$ scale. Four RO membranes of polyamide are used and examined about effect of chemical cleaning. EDTA (ethylene diamine tetraacetic acid) and SDS (sodium dodecil sulfate) and NaOH are applied for cleaning process after operation in synthetic water. Then, cleaning was performed with chemicals such concentration as 6hr, 12hr and 24hr, respectively. As a result, transmittances of FT-IR of four membranes are compared at each cleaning concentration. Ta/Tv shows difference of chemical composition between new membrane and cleaning membrane after cleaning. Type B of RO membrane is turned out to be most vulnerable to cleaning among four membranes. In terms of zeta potential, new membrane has -16 mV to +6 mV on pH while scaled membrane has -18 mV to 2 mV. However, it changed -23mV to 0.9 mV after cleaning. In comparison with existing salt rejection of RO membranes after cleaning, the rejection of the membranes goes down 0.7% maximum. Though cleaning changes the characteristics of membrane surface, it does not greatly affect salt rejection. pH is a critical factor to flux change in PA (polyamide) membrane.

• Resources Recycling
• /
• v.28 no.5
• /
• pp.19-29
• /
• 2019

Recently, it is increasing a amount of installized solar-cell rapidly, and waste Solar cell module are generated in according to the reduction of efficiency largely. Therefore, it is concerned at the environmental problems and recycling of valuable materials, greatly. The treatment processes of end-of-life photovoltaic modules are composed the disassembly of Aluminum frames, separation of Tempered glass, removal of Ethylene Vinyl Acetate and recovery of valuable Metals. For the efficient recycling, we are considered to the treatment technology seriously. And we are proposed on the general opinions according to the developing technology, EPR (Extended Producer Responsibility) problems and promotion plans for the activation of recycling industry.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.441-444
• /
• 2016

본 연구에서는 유입수의 유입 방향을 달리 하였을 때 각 여재의 처리효율 차이점을 조사하고자 하였다. 실험재료는 제올라이트, 화산석, 발포 세라믹, 폴리에틸렌(Poly Ethylene) 4종의 여재이며 총 용적 31 L의 아크릴반응조에 각각의 여재를 충진하였고 각각 상향류 및 하향류의 흐름 방식을 적용하여 2차에 걸쳐 여과실험을 진행하였다. 제거효율은 유입수 대비 유출수의 농도 변화를 통하여 관찰하였고, 수질 측정은 SS, COD, T-N, T-P 네 항목으로 수질공정시험법에 의거하여 분석하였다. 실험 결과 제올라이트는 SS, COD, T-N항목에서 상향류를 적용한 여과에서 제거효율이 높은 경향을 보였다. 특히 T-N항목의 경우 상향류 조건에서 49.2%, 하향류 조건에서 34.4%의 제거효율을 나타내 흐름조건별 제거효율에 가장 큰 격차를 보였다. 화산석의 경우 SS, COD, T-N항목은 흐름방식에 따른 제거효율에 주목할 만한 차이를 드러내지 않았으나 예외적으로 T-P항목만 상향류 조건에서 24.2%, 하향류 조건에서 15.9%의 제거효율을 나타냄으로써 상향류 조건에서 8.3% 높은 제거효율을 얻었다. 발포 세라믹 여재는 하향류를 적용한 여과에서 제거효율이 우세한 경향을 보였으며 특히 COD 항목의 경우 상향류 조건에서보다 하향류 조건에서 제거효율이 7.5% 향상된 결과를 얻었다. 폴리에틸렌 여재는 전반적으로 유입 조건에 따른 경향성을 나타내지 않았으나 예외적으로 SS항목의 경우 하향류 조건에서보다 상향류 조건을 적용한 여과에서 7.9% 높은 제거효율을 얻었다.

• Proceedings of the Korean Society of Developmental Biology Conference
• /
• 2003.10a
• /
• pp.113-113
• /
• 2003

This study was conducted to investigate the effect of vitrification solution(VS) on in vitro developmental competence of immature porcine oocytes. The immature porcine oocytes were exposed to the following vitrification solution, at RT. 1) EFS sol. : 20% ethylene glycol (EG) 3 min, 40% EG + 18%(w/v) Ficoll(MV70, 000) + 0.3 M sucrose 30 sec, 2) GE sol. : 10% glycerol 5 min, 10% G + 20% EG 5 min, 25% G +25% EG 30 sec, 3) EG sol : 1.5M EG 2.5 min, 5.5 M EG + 1.0 M sucrose 30 sec. Oocytes were immediately transferred into 1.0 M, 0.5 M, 0.25 M, 0125 M, 0 M sucrose solution for 2.5 min each at RT. After removal of VS, immature oocytes were matured in vitro and subsequently all oocytes were subjected to IVF followed in vitro culture for 7 days. Maturation rates of oocytes were 38.8%, 44.5%, 22.4% and 57.6%, in EFS, EG, GE and Control, respectively, maturation rates of oocytes in EG and Control was significantly higher than EFS and GE(P<0.01). Fertilization rates of oocytes in Control was significantly higher than other treated groups(P<0.05), but no difference were observed among treated groups. Polyspermic rates were no significant difference among four groups. Cleavage rates of oocytes were 21.9%, 47.1%, 19.0% and 65.9%, in EFS, EG, GE and Control, respectively, cleavage rates of oocytes in EG and Control was significantly higher than EFS and GE(P<0.05), but blastocyst formation rates were no significant difference among four groups. These results suggested that the use of EG solution could be a great challenge for reaching a successful vitrification of immature porcine oocytes.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2001.11a
• /
• pp.7-7
• /
• 2001

The increasing interest in light weight materials coupled to the need for cost -effective processing have combined to create a significant opportunity for aluminum P/M. particularly in the automotive industry in order to reduce fuel emissions and improve fuel economy at affordable prices. Additional potential markets for Al PIM parts include hand tools. Where moving parts against gravity represents a challenge; and office machinery, where reciprocating forces are important. Aluminum PIM adds light weight, high compressibility. low sintering temperatures. easy machinability and good corrosion resistance to all advantages of conventional iron bm;ed P/rv1. Current commercial alloys are pre-mixed of either the AI-Si-Mg or AL-Cu-Mg-Si type and contain 1.5% ethylene bis-stearamide as an internal lubricant. The powder is compacted in closed dies at pressure of 200-500Mpa and sintered in nitrogen at temperatures between $580~630^{\circ}C$ in continuous muffle furnace. For some applications no further processing is required. although most applications require one or more secondary operations such as sizing and finishing. These sccondary operations improve the dimension. properties or appearance of the finished part. Aluminum is often considered difficult to sinter because of the presence of a stable surface oxide film. Removal of the oxide in iron and copper based is usually achieved through the use of reducing atmospheres. such as hydrogen or dissociated ammonia. In aluminum. this occurs in the solid st,lte through the partial reduction of the aluminum by magncsium to form spinel. This exposcs the underlying metal and facilitates sintering. It has recently been shown that < 0.2% Mg is all that is required. It is noteworthy that most aluminum pre-mixes contain at least 0.5% Mg. The sintering of aluminum alloys can be further enhanced by selective microalloying. Just 100ppm pf tin chnnges the liquid phase sintering kinetics of the 2xxx alloys to produce a tensile strength of 375Mpa. an increilse of nearly 20% over the unmodified alloy. The ductility is unnffected. A similar but different effect occurs by the addition of 100 ppm of Pb to 7xxx alloys. The lend changes the wetting characteristics of the sintering liquid which serves to increase the tensile strength to 440 Mpa. a 40% increase over unmodified aIloys. Current research is predominantly aimed at the development of metal matrix composites. which have a high specific modulus. good wear resistance and a tailorable coefficient of thermal expnnsion. By controlling particle clustering and by engineering the ceramic/matrix interface in order to enhance sintering. very attractive properties can be achicved in the ns-sintered state. I\t an ils-sintered density ilpproaching 99%. these new experimental alloys hnve a modulus of 130 Gpa and an ultimate tensile strength of 212 Mpa in the T4 temper. In contest. unreinforcecl aluminum has a modulus of just 70 Gpa.

• Journal of Korean Society on Water Environment
• /
• v.21 no.4
• /
• pp.347-352
• /
• 2005

The isolated microorganisms, Pseudomonas stutzeri, Raoultella planticola (Klebsiella), Serratia fonticola from petroleum contaminated soil were enriched on benzene, toluene, ethylbenzene, o-xylene as carbon and energy sources, respectively. And the degradation characteristics of BTEX was observed in the mixed BTEX substrates. We found that the BTEX in mixed substrates were degraded more than 50% by three isolated microorganisms. Among three isolated microorganisms, the highest degradation rate was observed in Pseudomonas stutzeri, but the degradation rate was different according to microorganisms. In order to increase the degradation efficiency, we applied the co-culture of isolated three microorganisms. The mixture rate of pseudomonas stutzeri : Raoultella planticola (Klebsiella) : Serratia fonticola was follows ; 1:2:1, 1:1:2, and 2:1:1, respectively. In two co-culture of 1:2:1 and 1:1:2, degradation rate was lower than isolated microorganisms. However, degradation rate became higher than isolated microorganisms and the degradation rate of benzene, toluene, and ethylene was more than 95% in co-culture of 2:1:1. The degradation rate increased through the co-culture of isolated microorganisms, however, the growth rate decreased. This was resulted from the substrate competition between microorganisms. The co-culture of microorganisms is a effective method to increase the degradation efficiency of BTEX and the co-culture mixing rate is a important factor for determination of degradation efficiency.

• Journal of Periodontal and Implant Science
• /
• v.30 no.1
• /
• pp.145-157
• /
• 2000

Cytotoxic substances in dental calculus and root cementum of periodontally diseased teeth inhibit new attachment and regeneration. The purpose of scaling and root planing is to remove pathologic structures harboring these cytotoxic substances in order to create a biologically acceptable root surface. However, these procedures inevitably leave a non-biocompatible smear layer. Conventionally, the smear layer has been removed with low pH etching agents such as citric acid, phosphoric acid and tetracycline hydrochloride(TC). Lately, a supersaturated neutral pH etching solution of ethylene diamine tetraacetic acid(EDTA) has been found to be as effective as low pH etchants with respect to smear removal and to be superior in exposing root surfaceassociated collagen. The aim of the present study was to determine the effect of root surface treatment using EDTA on the initial attachment of human gingival fibroblasts. 27 human teeth, extracted due to severe periodontitis, were cut into dentin slices after root planing. The specimens were divided into TC group(treated with $50㎎/m{\ell}$ tetracycline-HCl, pH 1.52), EDTA group(treated with 17% EDTA, pH 7.4), and non-treated control group. After sterilization, 5th subcultured human gingival fibroblasts were seeded in each culture well containing a prepared root slice and incubated for 15 min., 60 min., and 4 hours in 5% $CO_2$ incubator at $37^{\circ}C$. At each incubation time, the number of attached fibroblasts were counted on the microphotographs taken at a magnification of x100. The difference of the number of attached cells between groups was statistically analyzed by the ANOVA followed by Duncan test in SPSS/PC＋programs. The results were as follows : 1. After incubation for 15 min, the attached cells were significantly more in EDTA group and TC group than non-treated control group(p<0.05), but there was no significance in the difference between EDTA group and TC group(p>0.1). 2. After incubation for 60 min and 4 hours, there was no significant difference in the number of attached cells between all groups(p>0.1). 3. In both EDTA group and TC group, there was no significant difference in the number of attached cells between different incubation(p>0.1). But in control group, the number of attached cells was significantly increased after incubation for 60 min, compared with incubation for 15 min(p<0.05). The above results suggest that root surface treatment using EDTA could enhance the initial attachment of gingival fibroblasts to root surface as effective as tetracycline-HCl.

• Korean Journal of Weed Science
• /
• v.7 no.1
• /
• pp.12-18
• /
• 1987

Seed dormancy and germination responses to light and gases were determined for Echinochloa colona (L.) Link. E. colons seeds did not require a period of after-ripening for breaking dormancy. Water movement occurred readily across the seed coat. Repeated cycles of hydration and dehydration reduced viability and thence germination. Water imbibition for 24 h increased seed moisture by 21%; seeds returned to their original weight after drying at room temperature for 13 h. Removal of seed-coats increased germination in the dark. Light stimulated germination. Germination at a daylight intensity of 51.9 $Wm^{-2}$ or less was significantly reduced. Germination of seeds which were exposed to light for 1 h each day was significantly less than that of seeds exposed for longer than 2 h a day. Seeds subjected to blue light had delayed and decreased germination compared to seeds exposed to red light. Ethylene or carbon dioxide exogenenously added in the presence of light stimulated germination. The addition of the two gases together had a synergistic effect. In the dark, however, the two gases did not increase germination.

• Korean Journal of Microbiology
• /
• v.53 no.4
• /
• pp.251-256
• /
• 2017

Some rhizobacteria were isolated, that have copper resistance and can confer copper resistance to plants allowing growth under copper stress. Isolated strains Pseudomonas veronii MS1 and P. migulae MS2 produced 0.13 and 0.26 mmol/ml of siderophore, that is a metal-chelating agent, and also showed 64.6 and 77.9% of biosorption ability for Cu in 20 mg/L Cu solution, respectively. Copper can catalyze a formation of harmful free radicals, which may cause oxidative stress in organisms. Removal activity of 1,1-diphenyl-2-picryl hydrazyl radical and antioxidant capacity of strains MS1 and MS2 increased up to 82.6 and 78.1%, respectively compared to those of control at 24 h of incubation. They exhibited 7.10 and $6.42{\mu}mol$ ${\alpha}$-ketobutyrate mg/h of 1-aminocyclopropane-1-carboxylic acid deaminase activity, respectively, which reduced levels of stress hormone, ethylene in plants, and also produced indole-3-acetic acid and salicyclic acid that can help plant growth under abiotic stress. All these results indicated that these copper-resistant rhizobacteria could confer copper resistance and growth promotion to plants.