• Elastomers and Composites
• /
• v.45 no.3
• /
• pp.212-216
• /
• 2010

The materials of the lithium ion battery gasket require chemical resistance to the electrolyte, electrical insulating, compression set, anti-contamination and heat resistance. To estimate suitability for rubber which has better performance to compression set than PFA, each compound were made with various rubbers, such as EPDM, NBR, FKM, FVMQ, VMQ and we checked the characteristics of each compound. Samples from each compound was deposited in Propylene Carbonate and tested for changing of Hardness and Volume during 1,000 hr with $80^{\circ}C$. EPDM and VMQ showed good performance to chemical resistance to the electrolyte, and also we could get the values over $10^{10}{\Omega}cm$ on volume resistance basis in electrical insulating. EPDM and VMQ were judged as the most suitable material.

• Journal of Industrial and Engineering Chemistry
• /
• v.68
• /
• pp.161-167
• /
• 2018

In this study, transition metal coated carbon nanofibers (CNFs) were synthesized and applied as anode materials of Li secondary batteries. CNFs/Ni foam was immersed into 0.01 M transition metal solutions after growing CNFs on Ni foam via chemical vapor deposition (CVD) method. Transition metal coated CNFs/Ni foam was dried in an oven at $80^{\circ}C$. Morphologies, compositions, and crystal quality of CNFs-transition metal composites were characterized by scanning electron microscopy (SEM), Raman spectroscopy (Raman), and X-ray photoelectron spectroscopy (XPS), respectively. Electrochemical characteristics of CNFs-transition metal composites as anodes of Li secondary batteries were investigated using a three-electrode cell. Transition metal/CNFs/Ni foam was directly employed as a working electrode without any binder. Lithium foil was used as both counter and reference electrodes while 1 M $LiClO_4$ was employed as the electrolyte after it was dissolved in a mixture of propylene carbonate:ethylene carbonate (PC:EC) at 1:1 volume ratio. Galvanostatic charge/discharge cycling and cyclic voltammetry measurements were taken at room temperature using a battery tester. In particular, the capacity of the synthesized CNFs-Fe was improved compared to that of CNFs. After 30 cycles, the capacity of CNFs-Fe was increased by 78%. Among four transition metals of Fe, Cu, Co and Ni coated on carbon nanofibers, the retention rate of CNFs-Fe was the highest at 41%. The initial capacity of CNFs-Fe with 670 mAh/g was reduced to 275 mAh/g after 30 cycles.

• Macromolecular Research
• /
• v.17 no.3
• /
• pp.174-180
• /
• 2009

Chemical modification of titanium/titanium oxide (Ti/$TiO_2$) substrates has recently gained a great deal of attention because of the applications of Ti/$TiO_2$-based materials to biomedical areas. The reported modification methods generally involve passive coating of Ti/$TiO_2$ substrates with protein-resistant materials, and poly(ethylene glycol) (PEG) has proven advantageous for bestowing a nonbiofouling property on the surface of Ti/$TiO_2$. However, the wider applications of Ti/$TiO_2$ based materials to biomedical areas will require the introduction of biologically active moieties onto Ti/$TiO_2$, in addition to nonbiofouling property. In this work, we therefore utilized surface-initiated polymerization to coat the Ti/$TiO_2$ substrates with polymers presenting the nonbiofouling PEG moiety and subsequently conjugated biologically active compounds to the PEG-presenting, polymeric films. Specifically, a Ti/$TiO_2$ surface was chemically modified to present an initiator for atom transfer radical polymerization, and poly(ethylene glycol) methacrylate (pEGMA) was polymerized from the surface. After activation of hydroxyl groups of poly(pEGMA) (pPEGMA) with N,N'-disuccinimidyl carbonate, biotin, a model compound, was conjugated to the pPEGMA films. The reactions were confirmed by infrared spectroscopy, X-ray photoelectron spectroscopy, contact angle goniometry, and ellipsometry. The biospecific binding of target proteins was also utilized to generate micropatterns of proteins on the Ti/$TiO_2$ surface.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.2
• /
• pp.100-103
• /
• 2000

Polymeric gel electrolytes based on polyacrylronitile blended with poly(vinylidene fluoride-co-hexafluoro-propylene)(P(VdF-co-HFP), which were reinforced with glass fiber cloth(GFC) to increase the mechanical strength, were prepared for the practical use in secondary battery. Test cell consisting of $LiCoO_2$ as a cathode and mesophase pich-based ca.bon fiber (MCF) as an anode material showed a capacity of 110 mAh/g based on the cathode weight at 0.2C rate at room temperature. Over $80\%$ of initial capacity was retained after 400cycles, indicating that GFC is suitable for a reinforcing material to increase the mechanical strength of gel based electrolytes.

• Korean Chemical Engineering Research
• /
• v.43 no.3
• /
• pp.407-411
• /
• 2005

YAG:Tb($Y_3Al_5O_{12}:Tb$) phosphor particles were prepared by spray pyrolysis from spray solution containing various types of flux materials. The effects of type of flux, organic material and post-treatment temperature on the characteristics of morphology, crystallinity and photoluminescence of YAG:Tb phosphor particles were investigated. Citric acid and ethylene glycol used as organic additive improved the photoluminescence intensity of the YAG:Tb phosphor particles without destruction of the morphology after post-treatment at high temperature. However, the spherical shape of the precursor particles obtained by spray pyrolysis from spray solution containing high amount of flux material disappeared after post-treatment at $1300^{\circ}C$. YAG:Tb phosphor particles prepared from spray solution containing lithium carbonate flux had fine size and regular morphology after post-treatment. Lithium carbonate used as flux material was also efficient in improvement of the photoluminescence intensity of the YAG:Tb phosphor particles. The optimum photoluminescence intensity of the YAG:Tb phosphor particles prepared from spray solution containing lithium carbonate flux was 189％ of that of the phosphor particles prepared from spray solution without flux material.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.13 no.1
• /
• pp.45-50
• /
• 2006

Papers were prepared from cut cocoons and mulberry branches, which are byproducts from sericulture industry. The long filament of silk should be cut into appropriate length in order to prepare paper and this was achieved by chemical method. By a mixture of sodium hydroxide and sodium carbonate solution, the silk filaments were cut into short fibers (less than 1 mm in length). Since the short silk fibers (sSf) could not bind each other by itself, starch and poly(ethylene oxide)(PEO) were added as a bonding agent. When starch and PEO were used in a ratio of 3:7, the silk papers had optimum mechanical properties for paper. Fibers from the skin of mulberry branches (MBF) were added to sSf to enhance the mechanical properties of pure silk paper. Bleaching of MBF was performed with a mixture of hydrogen peroxide and sodium silicate. The mechanical properties were greatly enhanced and the optimum blend ratio of MBF and sSf were 7:3. The mulberry/silk paper has good absorption property against formaldehyde, and therefore, the paper could be applied as a wall paper for preventing the sick house syndrome.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.220-224
• /
• 2009

The effect of addition of single and binary additives on the performance of dye-sensitized $TiO_2$ solar cells based on 1,2-dimethyl-3-propylimidazolium iodide (DMPII) in ethylene carbonate (EC) and gamma-butyrolactone (GBL) has been evaluated at different cell temperatures in the $30-120^{\circ}C$ range. The electrolyte containing a single additive, 2-(dimethylamino)-pyridine (DMAP) showed best performance, which showed further enhancement for an electrolyte containing binary additives, DMAP and 5-chloro-1-ethyl-2-methylimidazole (CEMI) in equal molar ratio. The performance of the dye sensitized solar cell (DSC) based on electrolyte containing binary additives were found to be better than an acetonitrile based electrolyte. The dependence of different photovoltaic parameters (Voc, Jsc, ff, n) of the DSC upon temperature has been studied over the $30-120^{\circ}C$ range and only a small decrease in conversion efficiency has been observed. Thus the electrolyte containing binary additives (DMAP, CEMI) in EC/GBL solvent and show better performance in the investigated temperature range ($30-120^{\circ}C$).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1138-1141
• /
• 2004

고분자 재료에 이온을 주입하면 표면전기저항이 이온주입조건에 따라 $10^{16}\Omega/sq$ 에서 $10^7\Omega/sq$ 까지 변하게 되며, 광학적 특성도 변하게 된다. 이는 산업적으로 대전방지 등에 적용이 가능하며 이러한 신소재 개발을 위하여 산업용 이온빔 표면처리 장치를 제작하고 인출광학을 기초로 이온빔을 제어하여 고분자 재료의 이온주입처리 양산기술을 개발하였다. 본 연구에서는 대면적, 대전류 이온빔 인출을 위한 이온원의 광학적 설계 및 빔라인에서의 솔레노이드 전자석을 이용한 빔프로파일 제어방법을 설명하였다. 사용된 고분자 소재는 PC(PolyCarbonate) 및 PET(PolyEthylene Teraphthalate)이며, 질소이온주입조건은 이온에너지 40-50 keV, 이온주입량 $5\times10^{15}$, $1\times10^{16}$, $7\times10^{16}ions/cm^2$의 조건으로 공정을 수행하였다. 또한 대전방지용 고분자 대량생산을 위한 연속 생산조건과 양산공정조건에 따른 표면전기저항변화를 관찰하였다.

• Journal of the Korean Applied Science and Technology
• /
• v.13 no.1
• /
• pp.67-74
• /
• 1996

This study was conducted to find a catalyst system which has high conversion and selectivity for the oxidative coupling of methane to produce ethane and ethylene. Various catalysts were tested in a fixed bed reactor ar $750^{\circ}C$, 1 atm, and the feed ratio($CH_4/O_2$) of 2/1. Under the reaction condition, 10wt%$PbSO_4/MgO$ catalyst showed the highest catalytic activity : methane conversion, $C_2$ selectivity and yield were 50, 40 and 20%, respectively. Catalysts containing sulfate compounds, 10wt%$PbSO_4/MgO$, 10wt%$MgSO_4/MgO$ and $Na_2SO_4/MgO$ revealed a moderate methane conversions such as 38, 50 and 50%, respectively and low $C_2$ selectivities such as 18, 5 and 9%, respectively. Catalysts containing carbonate compounds, 10wt%$PbCO_3/MgO$, 10wt%$Li_2CO_3/MgO$ and $NaCO_3/MgO$, also showed a moderate methane conversions such as 64, 44 and 51%, respectively and low $C_2$ selectivities such as 5, 6 and 2%, respectively. With the existence of chlorine and mercury, $C_2$ selectivity was decreased.

• Journal of Sericultural and Entomological Science
• /
• v.25 no.2
• /
• pp.44-50
• /
• 1984

The effects of sodium pyrophosphate, sodium tripolyphosposphate and ethylene diamine tetraacetic acid as a degumming aid reagent were investigated under the conditions of underground water and dimineralized water for the scouring water sources. The changes of water qualities by adding the condensed sodium phosphates and the physical properties of scoured silk fabric were examined, respectively. 1. The water hardness of underground water was decreased by adding the condensed sodium phosphates and it was further reduced according to the increasing temperature. The water hardness reducing power of sodium pyrophosphate was a little stronger than that of sodium tripolyphosphate. 2. The sodium silicate as an alkaline reagant for scouring decreased the water hardness, but the sodium carbonate increased it in the underground water. 3. The pH value of 0.4% soap and 0.25% sodium silicate mixed solution after boiling was. 9.80, but it was leveled upto 9.90 by adding 0.05% sodium pyrophosphate and upto 9.95 by 0.02% ehtylene diamine tetraacetic acid, respectively. 4. The masking action of Fe$\^$3+/ ions dissolved in the scouring water was more remarkable by ethylene diamine tetraacetic acid than by the condensed sodium phosphates. Of the condensations, sodium tripolyphosphate was more effective than sodium pyrophosphate in the action. 5. Genrally, the dimineralized water scouring increased the boil-off ratio with reducing the flexural rigidity of fabric which was negatively related with the favorablility of hand-touch more than the underground one did. 6. Under the underground water scouring, the addition of ethylene diamine tetraacetic acid increased the boil-of ratio and compressive elasticity of fabric with reducing the flexural rigidity more than that of the condensed sodium phosphates did. 7 The additions of sodium tripolyphosphate and ethylene diamine tetraacetic acid reduced the flexural rigidity of fabric with raising the boil-off ratio even in the dimineralized water scouring, but there was no sifnificant difference between both of them.