• JSTS:Journal of Semiconductor Technology and Science
• /
• 제6권3호
• /
• pp.199-205
• /
• 2006

Patterned sapphire substrates (PSS) were fabricated by a simple wet etching process with $SiO_2$ stripe masks and a mixed solution of $H_2SO_4$ and $H_3PO_4$. GaN layers were epitaxially grown on the PSS under the optimized 2-step growth condition of metalorganic vapor deposition. During the 1st growth step, GaN layers with triangular cross sections were grown on the selected area of the surface of the PSS, and in the 2nd growth step, the GaN layers were laterally grown and coalesced with neighboring GaN layers. The density of threading dislocations on the surface of the coalesced GaN layer was $2{\sim}4\;{\times}\;10^7\;cm^{-2}$ over the entire region. The epitaxial structure of near-UV light emitting diode (LED) was grown over the GaN layers on the PSS. The internal quantum efficiency and the extraction efficiency of the LED structure grown on the PSS were remarkably increased when compared to the conventional LED structure grown on the flat sapphire substrate. The reduction in TD density and the decrease in the number of times of total internal reflections of the light flux are mainly attributed due to high level of scattering on the PSS.

• The Journal of Advanced Prosthodontics
• /
• 제10권4호
• /
• pp.259-264
• /
• 2018

PURPOSE. The purpose of this study was to evaluate the effect of the zirconia surface architecturing technique (ZSAT) on the bond strength between veneering porcelain and zirconia ceramic. MATERIALS AND METHODS. 20 sintered zirconia ceramic specimens were used to determine the optimal surface treatment time, and were randomly divided into 4 groups based on treatment times of 0, 1, 2, and 3 hours. After etching with a special solution, the surface was observed under scanning electron microscope, and then the porcelain was veneered for scratch testing. Sixty 3 mol% yttria-stabilized tetragonal zirconia polycrystal ceramic blocks were used for tensile strength testing; 30 of these blocks were surface treated and the rest were not. Statistical analysis was performed using ANOVA, the Tukey post-hoc test, and independent t-test, and the level of significance was set at ${\alpha}=.05$. RESULTS. The surface treatment of the zirconia using ZSAT increased the surface roughness, and tensile strength test results showed that the ZSAT group significantly increased the bond strength between zirconia and veneering porcelain compared to the untreated group (36 MPa vs. 30 MPa). Optimal etching time was determined to be 2 hours based on the scratch test results. CONCLUSION. ZSAT increases the surface roughness of zirconia, and this might contribute to the increased interfacial bond strength between zirconia and veneering porcelain.

• 마이크로전자및패키징학회지
• /
• 제11권4호
• /
• pp.61-67
• /
• 2004

알루미늄 유전체의 표면적 증가에 의한 정전용량 값을 증가시키기 위하여, 1 M의 염산 에칭용액에 첨가제를 사용했을 때 나타나는 알루미늄 표면의 에칭특성의 변화를 조사하였다. 에칭액으로서 염산을 사용한 경우 알루미늄 표면에서 생성되는 에치피트의 형상과 단위 면적당 생성밀도가 균일하지 못하였다. 염산용액에 에틸렌글리콜이 첨가된 혼합용액에서 에칭을 실시했을 경우, 알루미늄 기지 표면에 미세하고 균일한 에치피트가 형성되어 표면적 증가의 효과가 크게 나타났다. 에틸렌글리콜이 첨가된 에칭액에서 제조된 유전체는 표면적 증가에 의한 효과로 높은 정전용량 값을 나타냈다.

• 한국결정성장학회지
• /
• 제5권2호
• /
• pp.87-93
• /
• 1995

Floating zone법으로 strontium titanate 단결정을 육성하였다. 성장조건은 공기 분위기하에서 성장속도 3mm/hr, 상부축 회전속도 20~25rpm, 하부축 회전속도 15~20rpm이었으며 육성한 단결정은 옅은 갈색을 띄고 있었으며 투명하였고 annealing 후 색깔이 옅어짐을 확인할 수 있었다. 성장방위는 [112] 방향이었으며 XRD, EDS로 화학양론적인 조성은 $SrTiO_3$단일 결정상임을 알 수 있었다. $350^{\circ}C$, KOH용액에서 5분동안 chemical etching하여 etch pit pattern을 조사하였으며 상온하에서$350^{\circ}C$의 온도 범위에서 유전상수 값을 조사하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.37-40
• /
• 2003

Amorphous $Al_2O_3$ nanotubes have been fabricated by utilizing the ZnO nanowires as template with wet etching method. ZnO nanowires synthesized by thermal evaporation are conformally coated with $Al_2O_3$ by atomic-layer deposition(ALD) method. The $Al_2O_3$-coated ZnO nanowires are of core-shell structure; ZnO core nanowires and $Al_2O_3$ shells. When the $ZnO/Al_2O_3$ core-shell structure is dipped in $H_3PO_4$ solution at $25^{\circ}C$ for a 6 min, the core ZnO materials are completely etched, and only $Al_2O_3$ nanotubes are remained. This nanotube fabrication is technically easier than others, and simply approachable. Transmission electron microscopy shows that the $Al_2O_3$ nanotubes have various thicknesses that can be controlled.

• 전기화학회지
• /
• 제5권2호
• /
• pp.43-46
• /
• 2002

Commercial titanium rod was anodized in three types of electrolytes such as 0.06 mol/L $\beta-glycerophosphate+0.3mol/L$ calcium acetate, 0.06mol/L $\beta-glycerophosphate+0.3mol/L$ sodium acetate and 0.06 mol/L $\beta-glycerophosphate+5mol/L$ calcium phosphate. The titanium oxide layer $(TiO_2)$ was characterized by scanning electron microscope (SEM), X-ray diffraction (XRD) and electron spectroscopy chemical analysis (ESCA). Numerous micropores were observed on the titanium oxide layer by SEM. The diameter of micropores increased with the increase of electrolytic voltage. The titanium oxide layer was composed of anatase structure. The phosphorous element was detected at 130 eV binding energy, but calcium was not found in the oxide layer because of lower contents. After anodizing the oxide layer was etched in the 30g/L NaOH solution at $80^{\circ}C$ for 1hr. The surroundings of micropores were much more smoothed and rounded than before alkaline etching.

• Applied Science and Convergence Technology
• /
• 제24권6호
• /
• pp.289-292
• /
• 2015

The etching processes of glass in aqueous hydrofluoric acid (HF) solutions were used to improve the current density of solar cell. In this study, the textured glass substrate has been etched by solution and the $TiO_2$ thin films have been prepared on this textured glass. After the $TiO_2$ film deposition the surface has been etched by HF under different concentration and the etched $TiO_2$ thin films had a longer electron lifetime and higher haze ratio as well as light scattering, resulting in 1.7 times increment of dye-sensitized solar-cell(DSSC) efficiency. Increases in the surface root-mean-square roughness of glass substrates from 80 nm to 1774 nm enhanced haze ratio in above 300 nm wavelength. In particular, haze ratio of etched $TiO_2$ films on textured glass showed gradually increasing tendency at 550 nm wavelength by increasing of HF concentration up to 10M, suggesting a formation of crater with various sizes on its surface.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.349-349
• /
• 2009

High quality ZnO:Al films were prepared on glass substrates by in-line RF magnetron sputtering and their surface morphologies were modified by wet-etching process in dilute acid solution to improve optical properties for application to silicon thin film solar cells as front electrode. The as-deposited films show a strong preferred orientation in [001] direction under our experimental conditions. A low resistivity below $5{\times}10^{-4}{\Omega}{\cdot}cm$ and high optical transmittance above 80% in a visible range are achieved in the films deposited at optimized conditions. After wet-etching, the surface morphologies of the films are changed dramatically depending on the deposition conditions, especially working pressure. The optical properties such as total/diffuse transmittance, haze and angular resolved distribution of light are varied significantly with the surface morphology feature, whereas the electrical properties are seldom changed. The cell performances of silicon thin film solar cells fabricated on the textured films are also evaluated in detail with comparison of commercial $SnO_2$:F films.

• 한국재료학회지
• /
• 제20권10호
• /
• pp.550-554
• /
• 2010

This work presents a fabrication procedure to make large-area, size-tunable, periodically different shape metal arrays using nanosphere lithography (NSL) combined with ashing and annealing. A polystyrene (PS, 580 ${\mu}m$) monolayer, which was used as a mask, was obtained with a mixed solution of PS in methanol by multi-step spin coating. The mask morphology was changed by oxygen RIE (Reactive Ion Etching) ashing and temperature processing by microwave heating. The Au or Pt deposition resulted in size tunable nano patterns with different morphologies such as hole and dots. These processes allow outstanding control of the size and morphology of the particles. Various sizes of hole patterns were obtained by reducing the size of the PS sphere through the ashing process, and by increasing the size of the PS sphere through annealing treatment, which resulted in tcontrolling the size of the metallic nanoparticles from 30 nm to 230 nm.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권2호
• /
• pp.93-99
• /
• 2006

In this paper, we fabricated and evaluated polydimethylsiloxane(PDMS)-based flexible and implantable micro electrodes. The electrode patterning was carried out with the photolithography and chemical etching process after e-beam evaporation of 100 ATi and 1000 A Au. The PDMS substrate was treated by oxygen plasma using reactive ion etching(RIE) system to improve the adhesiveness of PDMS and metal layers. The minimum line width of fabricated micro electrode was 20 $\mu$m. After finished patterning, we did packaging with PDMS and then brought up the electrode's part about 40 $\mu$m with gold electroplating. The Hank's balanced salt solution(HBSS) test was carried out for 6 month for endurance of fabricated micro electrode. We carried out in-vivo test for the evaluation of biocompatibility by implanting electrodes under the ICR mouse skin for 42 days.