• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1448-1449
• /
• 2006

Pb(Zr,Ti)$O_3$ is one of the most attractive ferroelectric materials for realizing the FeRAM due to its higher remanant polarization and the ability to withstand higher coercive fields. Generally, the ferroelectric materials were patterned by a plasma etching process for high-density FeRAM. The applicable possibility of CMP process to pattern Pb(Zr,Ti)$O_3$ instead of plasma etching process was investigated in our previous study for improvement of an angled sidewall which prevents the densification of ferroelectric memory and is apt to receive the plasma damage. Our previous study showed that good removal rate with the excellent surface roughness compared to plasma etching process were obtained by CMP process for the patterning of Pb(Zr,Ti)$O_3$. The suitable selectivity to TEOS without any damage to the structural property of Pb(Zr,Ti)$O_3$ was also guaranteed. In this study, the removal mechanism of $Pb_{1.1}(Zr_{0.52}Ti_{0.48})O_3$ coated by sol-gel method was investigated. Surface analysis of polished specimens at the best and worst conditions was carried out by XPS.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.12
• /
• pp.1271-1276
• /
• 2004

Two-dimensionally arrayed nanocolumn lattices were fabricated by using double-exposure laser holographic method. The hexagonal lattice was formed by rotating the sample with 60 degree while the square lattice by 90 degree before the second laser-exposure. The reactive ion etching for a typical time of 30 min using CH$_4$/H$_2$ plasma enhanced the aspect-ratio by more than 1.5 with a slight increase of the bottom width of columns. The etch-damage was observed by photoluminescence (PL) spectroscopy which was removed by the wet chemical etching using HBr/$H_2O$$_2$/$H_2O$ solution, leading into the enhanced PL intensities of the PCs.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.107-107
• /
• 2009

본 연구에서는 중성빔을 이용한 Atomic Layer Etching(ALET) system을 이용하여 $ZrO_2$의 atomic layer etching mechanism에 대하여 연구하였다. Ar neutral beam irradiation dose와 $BCl_3$ gas pressure의 변화에 따라 $ZrO_2$ etch rate와 RMS roughness를 관찰했을 때, Ar neutral beam irradiation dose이 $1.485{\times}10^{16}atoms/cm^2{\bullet}cycle$ 이상이고 $BCl_3$ gas pressure가 0.15mTorr 이상 일 때 $ZrO_2$ etch rate은 $1.07\;{\AA}/cycle$의 일정한 값에서 유지됨을 확인하였다. 그리고 ALET와 ICP Etcher을 통해 $ZnO_2$를 각각 식각하여 physically or chemically damage를 비교한 결과, ALET가 기존의 ICP Etcher system보다 $ZrO_2$ 식각공정에 대해 적은 damage를 받는 것을 ARXPS를 통해 관찰 하였다.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.4
• /
• pp.113-118
• /
• 2011

According to the high accuracy of semiconductor equipments, PCB substrate with much thin thickness is required. However, it is very difficult to sustain the PCB substrate without deformation in case of horizontal installation, due to low bending stiffness. In this research, new PCB process equipment with vertical installation has been developed in order to solve the problem of PCB substrate damage during etching process. As the main parts of etching system on PCB substrate, PCB substrate and JIG are analyzed through finite element method and experimental test. Through the analysis results of stress state, we could find the optimal JIG design to make the damage as low as possible.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.5
• /
• pp.516-521
• /
• 2001

Dry etching of Si wafer and $SiO_2$ layers was performed using He/Cl$_2$ mixture plasma by diode-type reactive ion etcher (RIE) system. For Si etching, the Cl molecules react with the Si molecules on the surface and become chemically stable, indicating that the reactants need energetic ion bombardment. During the ion assisted desorption, energetic ions would damage the photoresist (PR) and produce the bad etch Si-profile. Moreover, we have examined the characteristics of the Cl-Si reaction system, and developed the new fabrication procedures with a $Cl_2$/He mixture for Si and $SiO_2$-etching. The developed novel fabrication procedure allows the RIE to be unexpensive and useful a Si deep etching system. Since the etch rate was proved to increase linearly with fHe and the selectivity of Si to $SiO_2$ etch rate was observed to be inversely proportional to fHe.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.279-282
• /
• 2001

The IBE(ion beam etching)-induced Schottky barrier variation which depends on various etching history related with ion energy, incident angle and etching time has been investigated using voltage-current, capacitance-voltage characteristics of metal-etched silicon contact and morphology of etched surface were studied using AFM(atomic force microscope). For ion beam etched n-type silicons, Schottky barrier is reduced according to ion beam energy. It can be seen that amount of donor-like positive charge created in the damaged layer is proportional to the ion energy. By contrary, for ion beam etched p-type silicons, the Schottky barrier and specific contact resistance are both increased. Not only etching time but also incident angle of ion beam has an effect on barrier height. Taping-mode AFM analysis shows increased roughness RMS(Root-Mean-Square) and depth distribution due to ion bombardment. Annealing in an N$_2$ ambient for 30 min was found to be effective in improving the diode characteristics of the etched samples and minimum annealing temperatures to recover IBE-induced barrier variation were related to ion beam energy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.299.2-299.2
• /
• 2013

We investigated the potassium remaining on a crystalline silicon solar cell after potassium hydroxide (KOH) etching and its effect on the lifetime of the solar cell. KOH etching is generally used to remove the saw damage caused by cutting a Si ingot; it can also be used to etch the rear side of a textured crystalline silicon solar cell before atomic layer-deposited Al2O3 growth. However, the potassium remaining after KOH etching is known to be detrimental to the efficiency of Si solar cells. In this study, we etched a crystalline silicon solar cell in three ways in order to determine the effect of the potassium remnant on the efficiency of Si solar cells. After KOH etching, KOH and tetramethylammonium hydroxide (TMAH) were used to etch the rear side of a crystalline silicon solar cell. To passivate the rear side, an Al2O3 layer was deposited by atomic layer deposition (ALD). After ALD Al2O3 growth on the KOH-etched Si surface, we measured the lifetime of the solar cell by quasi steady-state photoconductance (QSSPC, Sinton WCT-120) to analyze how effectively the Al2O3 layer passivated the interface of the Al2O3 layer and the Si surface. Secondary ion mass spectroscopy (SIMS) was also used to measure how much potassium remained on the surface of the Si wafer and at the interface of the Al2O3 layer and the Si surface after KOH etching and wet cleaning.

• 한국초전도학회:학술대회논문집
• /
• v.11
• /
• pp.50-50
• /
• 2001

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2003.10a
• /
• pp.63-63
• /
• 2003

• Journal of Sensor Science and Technology
• /
• v.32 no.5
• /
• pp.328-333
• /
• 2023

This study experimentally verified the etch rate of the SiO₂ sacrificial layer etching process with a single etch hole using vapor-phase hydrogen fluoride (VHF) etching. To fabricate small-sized polysilicon etch holes, both circular and triangular pattern masks were employed. Etch holes were fabricated in the polysilicon thin film on the SiO₂ sacrificial layer, and VHF etching was performed to release the polysilicon thin film. The lateral etch rate was measured for varying etch hole sizes and sacrificial layer thicknesses. Based on the measured results, we obtained an approximate equation for the etch rate as a function of the etch hole size and sacrificial layer thickness. The etch rates obtained in this study can be utilized to minimize structural damage caused by incomplete or excessive etching in sacrificial layer processes. In addition, the results of this study provide insights for optimizing sacrificial layer etching and properly designing the size and spacing of the etch holes. In the future, further research will be conducted to explore the formation of structures using chemical vapor deposition (CVD) processes to simultaneously seal etch hole and prevent adhesion owing to polysilicon film vibration.