• 한국재료학회지
• /
• 제33권12호
• /
• pp.511-516
• /
• 2023

Amorphous In-Ga-Zn-O (a-IGZO) thin film transistors (TFTs) with a coplanar structure were fabricated to investigate the feasibility of their potential application in large size organic light emitting diodes (OLEDs). Drain currents, used as functions of the gate voltages for the TFTs, showed the output currents had slight differences in the saturation region, just as the output currents of the etch stopper TFTs did. The maximum difference in the threshold voltages of the In-Ga-Zn-O (a-IGZO) TFTs was as small as approximately 0.57 V. After the application of a positive bias voltage stress for 50,000 s, the values of the threshold voltage of the coplanar structure TFTs were only slightly shifted, by 0.18 V, indicative of their stability. The coplanar structure TFTs were embedded in OLEDs and exhibited a maximum luminance as large as 500 nits, and their color gamut satisfied 99 % of the digital cinema initiatives, confirming their suitability for large size and high resolution OLEDs. Further, the image density of large-size OLEDs embedded with the coplanar structure TFTs was significantly enhanced compared with OLEDs embedded with conventional TFTs.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.68-69
• /
• 2005

BTO ($BaTiO_3$) thin film is one of the high dielectric materials for high-density dynamic random access memories (DRAMs) due to its relatively high dielectric constant. It is generally known that BTO film is difficult to be etched by plasma etching, but high etch rate with good selectivity to pattern mask was required. The problem of sidewall angle also still remained to be solved in plasma etching of BTO thin film. In this study, we first examined the patterning possibility of BTO film by chemical mechanical polishing (CMP) process instead of plasma etching. The sputtered BTO film on TEOS film as a stopper layer was polished by CMP process with the self-developed $BaTiO_3$- and $TiO_2$-mixed abrasives slurries (MAS), respectively. The removal rate of BTO thin film using the$ BaTiO_3$-mixed abrasive slurry ($BaTiO_3$-MAS) was higher than that using the $TiO_2$-mixed abrasive slurry ($TiO_2$-MAS) in the same concentrations. The maximum removal rate of BTO thin film was 848 nm/min with an addition of $BaTiO_3$ abrasive at the concentration of 3 wt%. The sufficient within-wafer non-uniformity (WIWNU%)below 5% was obtained in each abrasive at all concentrations. The surface morphology of polished BTO thin film was investigated by atomic force microscopy (AFM).

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.61-63
• /
• 2005

Pentacene based OTFT on PC and PES plastic substrates have been fabricated in a scale of 5 inches. We could get a small OTFT device enough to be applicable for AMOLED by acquiring the at least misalignment margin through a contact aligner. And also we could find out the degradation of device parameter through the integration processes and improve the properties by using a buffer layer as an etch stopper in an active patterning. Through these, the mobility of device is more than about $0.2cm^2/Vs$ and $I_{on}/I_{off}$ is higher than $10^5$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 영호남 합동 학술대회 및 춘계학술대회 논문집 센서 박막 기술교육
• /
• pp.101-102
• /
• 2006

BTO ($BaTiO_3$) thin film is one of the high dielectric materials for high-density dynamic random access memories (DRAMs) due to its relatively high dielectric constant, It is generally known that BTO film is difficult to be etched by plasma etching, but high etch rate with good selectivity to pattern mask was required. The problem of sidewall angle also still remained to be solved in plasma etching of BTO thin film. In this study, we first examined the patterning possibility of BTO film by chemical mechanical polishing (CMP) process instead of plasma etching. The sputtered BTO film on TEOS film as a stopper layer was polished by CMP process with the sell-developed $BaTiO_3$- and $TiO_2$-mixed abrasives slurries (MAS). respectively. The removal rate of BTO thin film using the $BaTiO_3$-mixed abrasive slurry ($BaTiO_3$-MAS) was higher than that using the $TiO_2$-mixed abrasive slurry ($TiO_2$-MAS) in the same concentrations. The maximum removal rate of BTO thin film was 848 nm/min with an addition of $BaTiO_3$ abrasive at the concentration of 3 wt%.

• 한국정보통신학회논문지
• /
• 제11권6호
• /
• pp.1099-1103
• /
• 2007

본 연구는 기존의 방식으로 만든 비정질 실리콘 박막 트랜지스터의 제조공정에서 발생되는 결함에 대한 원인을 분석하고 해결함으로써 수율을 증대시키고 신뢰성을 개선하고자한다. 본 연구의 수소화 된 비정질 실리콘 박막 트랜지스터는 Inverted Staggered 형태로 게이트 전극이 하부에 있다. 실험 방법은 게이트전극, 절연층, 전도층, 에치스토퍼 및 포토레지스터층을 연속 증착한다. 스토퍼층을 게이트 전극의 패턴으로 남기고, 그 위에 n+a-Si:H층 및 NPR(Negative Photo Resister)을 형성시킨다. 상부 게이트 전극과 반대의 패턴으로 NPR층을 패터닝 하여 그것을 마스크로 상부 n+a-Si:H 층을 식각하고, 남아있는 NPR층을 제거한다. 그 위에 Cr층을 증착한 후 패터닝하여 소오스-드레인 전극을 위한 Cr층을 형성시켜 박막 트랜지스터를 제조한다. 이렇게 제조한 박막 트랜지스터에서 생기는 문제는 주로 광식각공정시 PR의 잔존이나 세척시 얇은 화학막이 표면에 남거나 생겨서 발생되며, 이는 소자를 파괴시키는 주된 원인이 된다. 그러므로 이를 개선하기 위하여 ashing이나 세척공정을 보다 엄격하게 수행하였다. 이와 같이 공정에 보다 엄격한 기준의 세척과 여분의 처리 공정을 가하여 수율을 확실히 개선 할 수 있었다.