• Clean Technology
• /
• v.25 no.1
• /
• pp.63-73
• /
• 2019

Numerical analysis was done to evaluate the chemical reaction and the reduction rate inside of selective non-catalytic reduction to denitrification in combustion process. The $NO_X$ reduction in selective non-catalytic reduction is converted to not only nitrogen but also nitrous oxide. Simultaneous $NO_X$ reduction and nitrous oxide generation suppressing is required in selective non-catalytic reduction because nitrous oxide influences the global warming as a greenhouse gas. The current study was performed compare the computational analysis in the same temperature and amount of NaOH, and in comparison with the previous research experiments and confirmed the reliability of the computational fluid dynamics. Additionally, controlling the addition amount of NaOH to predict the $NO_X$ reduction efficiency and nitrous oxide production. Numerical analysis was done to check the mass fraction of each material in the measurement point at the end of selective non-catalytic reduction. Experimental Value and simulation value by numerical analysis showed an error of up to 18.9% was confirmed that a generally well predicted. and it was confirmed that the widened temperature range of more than 70% $NO_X$ removal rate is increased when the addition amount of NaOH. So, large and frequent changes of the reaction temperature waste incineration facilities are expected to be effective.

• Journal of the Korean Institute of Gas
• /
• v.22 no.6
• /
• pp.90-103
• /
• 2018

This paper presents the development of two ANN models which can predict an optimum production rate by controlling choke size in oil well, and gas injection rate in gas-lift well. The input data was solution gas-oil ratio, water cut, reservoir pressure, and choke size or gas injection rate. The output data was wellhead pressure and production rate. Firstly, a range of each parameters was decided by conducting sensitive analysis of input data for onshore oil well. In addition, 1,715 sets training data for choke size decision model and 1,225 sets for gas injection rate decision model were generated by nodal analysis. From the results of comparing between the nodal analysis and the ANN on the same reservoir system showed that the correlation factors were very high(>0.99). Mean absolute error of wellhead pressure and oil production rate was 0.55%, 1.05% with the choke size model, respectively. And the gas injection rate model showed the errors of 1.23%, 2.67%. It was found that the developed models had been highly accurate.

• Journal of Korean Society of Forest Science
• /
• v.108 no.3
• /
• pp.364-371
• /
• 2019

This study was conducted to provide the basic information for a reasonable forest management plan and sustainable forest management by developing a dominant tree height growth model using diameter at breast height (DBH) and site index curves for Pinus densiflora and Chamaecyparis obtusa growing in Jeolla-do. The altitude, slope, orientation, soil type, height and DBH of a dominant tree, and the ages of trees were measured for 3055 Pinus densiflora trees (611 plots) and 3345 Chamaecyparis obtusa trees (699 plots), and these data were used to develop a customized afforestation map. In the dominant tree height growth model, the relationship to DBH was used in the Petterson, Michailow, and log equations. Also, a dominant tree height growth model in relationship to age used the Chapman-Richards, Schumacher, and Gompertz equations. The Petterson equation, which has a lower mean square error, was used to model dominant tree height growth in relationship to DBH. In the model of dominant tree height growth in relationship to age, three kinds of equations were considered to have little statistical difference. Therefore, the Chapman-Richards equation was chosen for modeling on the national level. Thirtyyears was used as the base age, which is an important factor for estimating the site index curves. In the results, a more varied range of site index family curves with 6-18 was developed for Pinus densiflora, and with 6-22 for Chamaecyparis obtusa. As the new site index curves indicated influences on growth of Pinus densiflora and Chamaecyparis obtusa, a reasonable forest management plan will be possible in the future for Jeolla-do.

• Journal of Digital Convergence
• /
• v.17 no.11
• /
• pp.207-213
• /
• 2019

The fuel-cut coast-down driving mode is activated when the acceleration pedal is released with transmission gear engaged, and it's a default function for electronic-controlled engine of vehicles. The fuel economy becomes better because fuel injection stops during fuel-cut driving mode. A fuel-cut detection method is suggested in the study and it's based on the speed, acceleration and road gradient data from GPS sensor. It detects fuel-cut driving mode by comparing calculated acceleration and realtime acceleration value. The one is estimated with driving resistance in the condition of fuel-cut driving and the other is from GPS sensor. The detection accuracy is about 80% when the method is verified with road driving data. The result is estimated with 9,600 data set of vehicle speed, acceleration, fuel consumption and road gradient from test driving on the road of 12km during 16 minutes, and the road slope is rather high. It's easy to detect fuel-cut without injector signal obtained by connecting wire. The detection error is from the fact that the variation range of speed, acceleration and road gradient data, used for road resistance force, is larger than the value of fuel consumption data.

• Journal of the Korean Geosynthetics Society
• /
• v.19 no.4
• /
• pp.41-50
• /
• 2020

Since cracks in concrete structures expedite corrosion of reinforced concrete over a long period of time, regular on-site inspections are essential to ensure structural usability and prevent degradation. Most of the safety inspections of facilities rely on visual inspection with naked eye, so cost and time consuming are severe, and the reliability of results differs depending on the inspector. In this study, a portable measuring device that can be used for safety diagnosis and maintenance was developed as a device that measures the width and length of concrete cracks through image analysis of cracks photographed with a camera. This device captures the cracks found within a close distance (3 m), and accurately calculates the unit pixel size by laser distance measurement, and automatically calculates the crack length and width with the image processing algorithm developed in this study. In measurement results using the crack image applied to the experiment, the measurement of the length of a 0.3 mm crack within a distance of 3 m was possible with a range of about 10% error. The crack width showed a tendency to be overestimated by detecting surrounding pixels due to vibration and blurring effect during the binarization process, but it could be effectively corrected by applying the crack width reduction function.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.148-155
• /
• 2021

As robot technology advances, research on the driving system of mobile robots is actively being conducted. The driving system of a mobile robot configured based on two-wheels and four-wheels has an advantage in unidirectional driving such as a straight line, but has disadvantages in turning direction and rotating in place. A ball robot using a ball as a wheel has an advantage in omnidirectional movement, but due to its structurally unstable characteristics, balancing control to maintain attitude and driving control for movement are required. By estimating the position from an encoder attached to the motor, conventional ball robots have a limitation, which causes the accumulation of errors during driving control. In this study, a driving control system was proposed that estimates the position coordinates of a ball robot through image processing and uses it for driving control. A driving control system including an image processing unit, a communication unit, a display unit, and a control unit for estimating the position of the ball robot was designed and manufactured. Through the driving control experiment applying the driving control system of the ball robot, it was confirmed that the ball robot was controlled within the error range of ±50.3mm in the x-axis direction and ±53.9mm in the y-axis direction without accumulating errors.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.6
• /
• pp.590-596
• /
• 2020

In the island areas where system connection with the commercial power grid is difficult, it is quite important to find a method to efficiently manage energy produced with independent microgrids. In this paper, a prosumer management system for P2P power transaction was realized through the testing the power meter and the response rate of the collected data for the power produced in the small-scale microgrids in which hybrid models of solar power and wind power were implemented. The power network of the microgrid prosumer was composed of mesh structure and the P2P power transaction was tested through the power meter and DC power transmitter in the off-grid sites which were independently constructed in three places. The measurement values of the power meter showed significant results of voltage (average): 380V + 0.9V, current (average): + 0.01A, power: 1000W (-1W) with an error range within ±1%. Stabilization of the server was also confirmed with the response rate of 0.32 sec. for the main screen, 2.61 sec. for the cumulative power generation, and 0.11 sec for the power transaction through the transmission of 50 data in real time. Therefore, the proposed system was validated as a P2P power transaction system that can be used as an independent network without transmitted by Korea Electric Power Corporation (KEPCO).

• Atmosphere
• /
• v.31 no.5
• /
• pp.577-592
• /
• 2021

This study evaluates the predictability of the number of days of heat and cold damages by growth stages of rice in South Korea using the hindcast data (1986~2020) produced by Pusan National University Coupled General Circulation Model-Weather Research and Forecasting (PNU CGCM-WRF) model chain. The predictability is accessed in terms of Root Mean Square Error (RMSE), Normalized Standardized Deviations (NSD), Hit Rate (HR) and Heidke Skill Score (HSS). For the purpose, the model predictability to produce the daily maximum and minimum temperatures, which are the variables used to define heat and cold damages for rice, are evaluated first. The result shows that most of the predictions starting the initial conditions from January to May (01RUN to 05RUN) have reasonable predictability, although it varies to some extent depending on the month at which integration starts. In particular, the ensemble average of 01RUN to 05RUN with equal weighting (ENS) has more reasonable predictability (RMSE is in the range of 1.2~2.6℃ and NSD is about 1.0) than individual RUNs. Accordingly, the regional patterns and characteristics of the predicted damages for rice due to excessive high- and low-temperatures are well captured by the model chain when compared with observation, particularly in regions where the damages occur frequently, in spite that hindcasted data somewhat overestimate the damages in terms of number of occurrence days. In ENS, the HR and HSS for heat (cold) damages in rice is in the ranges of 0.44~0.84 and 0.05~0.13 (0.58~0.81 and -0.01~0.10) by growth stage. Overall, it is concluded that the PNU CGCM-WRF chain of 01RUN~05RUN and ENS has reasonable capability to predict the heat and cold damages for rice in South Korea.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.8
• /
• pp.29-36
• /
• 2022

The importance of subsurface information is becoming crucial in urban area due to increase of underground construction. The position of underground facilities should be identified precisely before excavation work. Geophyiscal exporation method such as ground penetration radar (GPR) can be useful to investigate the subsurface facilities. GPR transmits electromagnetic waves to the ground and analyzes the reflected signals to determine the location and depth of subsurface facilities. Unfortunately, the readability of GPR signal is not favorable. To overcome this deficiency and automate the GPR signal processing, deep learning technique has been introduced recently. The accuracy of deep learning model can be improved with abundant training data. The ground is inherently heteorogeneous and the spacially variable ground properties can affact on the GPR signal. However, the effect of ground heterogeneity on the GPR signal has yet to be fully investigated. In this study, ground heterogeneity is simulated based on the fractal theory and GPR simulation is carried out by using gprMax. It is found that as the fractal dimension increases exceed 2.0, the error of fitting parameter reduces significantly. And the range of water content should be less than 0.14 to secure the validity of analysis.

• Korean Journal of Remote Sensing
• /
• v.38 no.6_1
• /
• pp.1257-1271
• /
• 2022

Recently, many Earth observation optical satellites have been developed, as their demands were increasing. Therefore, a rapid preprocessing of satellites became one of the most important problem for an active utilization of satellite images. Satellite image matching is a technique in which two images are transformed and represented in one specific coordinate system. This technique is used for aligning different bands or correcting of relative positions error between two satellite images. In this paper, we propose an automatic image matching method among satellite images with different ground sampling distances (GSDs). Our method is based on improved feature matching and robust estimation of transformation between satellite images. The proposed method consists of five processes: calculation of overlapping area, improved feature detection, feature matching, robust estimation of transformation, and image resampling. For feature detection, we extract overlapping areas and resample them to equalize their GSDs. For feature matching, we used Oriented FAST and rotated BRIEF (ORB) to improve matching performance. We performed image registration experiments with images KOMPSAT-3A and RapidEye. The performance verification of the proposed method was checked in qualitative and quantitative methods. The reprojection errors of image matching were in the range of 1.277 to 1.608 pixels accuracy with respect to the GSD of RapidEye images. Finally, we confirmed the possibility of satellite image matching with heterogeneous GSDs through the proposed method.