• Corrosion Science and Technology
• /
• v.12 no.3
• /
• pp.125-131
• /
• 2013

The most common pipe wall thinning degradation mechanisms that can occur in the steam and feedwater systems are FAC (Flow Acceleration Corrosion), cavitation, flashing, and LDIE (Liquid Droplet Impingement Erosion). Among those degradation mechanisms, FAC has been investigated by many laboratories and industries. Cavitation and flashing are also protected on the piping design phase. LDIE has mainly investigated in aviation industry and turbine blade manufactures. On the other hand, LDIE has been little studied in NPP (Nuclear Power Plant) industry. This paper presents the development of prediction system for pipe wall thinning caused by LDIE in terms of erosion rate based on air-water ratio and material. Experiment is conducted in 3 cases of air-water ratio 0.79, 1.00, and 1.72 using the three types of the materials of A106B, SS400, and A6061. The main control parameter is the air-water ratio which is defined as the volumetric ratio of water to air (0.79, 1.00, 1.72). The experiments were performed for 15 days, and the surface morphology and hardness of the materials were examined for every 5 days. Since the spraying velocity (v) of liquid droplets and their contact area ($A_c$) on specimens are changed according to the air-water ratio, we analyzed the behavior of LDIE for the materials. Finally, the prediction equations(i.e. erosion rate) for LDIE of the materials were determined in the range of the air-water ratio from 0 to 2%.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.37 no.1
• /
• pp.82-90
• /
• 2010

This study examined the effect of adhesive tape supplemented with sodium fluoride on the prevention of dental erosion in vitro. Sound bovine tooth samples were selected and divided randomly into the following 4 groups according to the material treatments: group 1, APF gel; group 2, fluoride varnish; and groups 3 and 4, fluoride tape supplemented with 5% NaF in either a methyl cellulose or poly vinyl acetate carrier, respectively. All specimens were submitted to alternate cycles of acid exposure in a cola beverage (pH 4.3) and artificial saliva for $6\;{\times}\;5\;min/day$ over a 5 day period. The micro-hardness was recorded each day and the lesion depth was measured after 5 days. The micro-hardness of the experimental sides of groups 2, 3 and 4 were significantly higher than that of their control sides and the experimental side of group 1 during the experimental period (p<0.05) except on the 5th day. The enamel surfaces of treatment groups 2, 3 and 4 showed significantly higher resistance to mineral loss in terms of the erosion depth (p<0.05) than group 1 and their control sides. There was no statistically significant difference among group 2, 3 and 4, indicating that the fluoride varnish and tapes produce similar results. Fluoride adhesive tapes are effective in reducing the progression of erosion and can be recommended for young patients who are more susceptible to dental erosion.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.3
• /
• pp.39-41
• /
• 1974

Bastard indigo, prevailing shrub species planted in erosion control work to constitute vegetation, is proved to be usefull for pulp material other than existing usage of green manure or fuel. Pulp made from bastard indigo is good enough for filler pulp though the quality of it is not remarkably excellent. (1) Sorts of paper possible to make from this pulp. Packing paper of medium grade. (general packing paper except heavy packing) (2) Traits of this pulp as for pulp material (A) It is more preferable than annual plants in these respects, ego collection, transport and storage of pulp material, and yield, freeness and chemical consumption of pulp. (B) Annual probable production of pulp material per ha from this plant is higher than that from long-term tree species or similar to that from fast growing species. (C) Its cultivation on eroded area is welcomed and consecutive annual production of material by copice method is also proved possible.

• Journal of Korean Society of Forest Science
• /
• v.101 no.3
• /
• pp.412-425
• /
• 2012

Concrete Soil Erosion Control Dam, which blocks flow of debris flow in torrential stream, are reported to lose expected functions due to structural failure and collapses, caused by poor construction, material deterioration and external impacts. In this paper, an integrity assessment technique for debris barriers was proposed, which allows preliminary detection of problems inherent in debris barriers. The proposed integrity assessment technique is a non-destructive method based on SASW method, one of surface-wave tests. In this paper, a practical procedure and analysis guidelines in applying the SASW technique to debris barrier was proposed and its validity was verified using five decrepit debris barriers older than 20-year old. As a result, the SASW method was validated for the reliable grade evaluation method for concrete soil erosion control dam, and the resulting grades turned out to agree with the results determined by Sabang Associations.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.443-444
• /
• 2002

The uniformity of field oxide is critical to isolation property of device in STI, so the control of field oxide thickness in STI-CMP becomes enormously important. The loss of field oxide in shallow trench isolation comes mainly from dishing and erosion in STI-CMP. In this paper, the effect of slurries on the dishing was investigated with both blanket and patterned wafers were selected to measure the removal rate, selectivity and dishing amount. Dishing was a strong function of pattern spacing and types of slurries. Dishing was significantly decreased with decreasing pattern spacing for both slurries. Significantly lower dishing with ceria based slurry than with silica based slurry were achieved when narrow pattern spacing were used. Possible dishing mechanism with two different slurries were discussed based on the observed experimental results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.10
• /
• pp.647-651
• /
• 2016

The power relay can easily control high voltage and high current through metallic contacts. In addition, it has the advantage in reasonable price. So it has been used in many applications. But the power relay has a weak point by mechanical movements. These mechanical movements cause the bouncing phenomenon. Arc and bouncing phenomenon are the main causes of electric abrasion and material erosion. In this study, mechanical repetitive experiments and repetitive experiments in electrically connected state are conducted. Then these two experimental results in terms of bouncing phenomenon and changes in the contact surface are compared. In all number of repetitions, contacts in an electrically connected state cause smaller number of bounce. Also, It has lower contents of silver on eroded surface than the other. The experimental results would be helpful to the further study of contacts life span.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.1
• /
• pp.11-14
• /
• 2004

An rf triode magnetron sputtering system is designed and installed its construction in vacuum chamber. In order to calibrate the rf triode magnetron sputtering for thin films deposition processes, the effects of different glow discharge conditions were investigated in terms of the deposition rate measurements. The basic parameters for calibrating experiment in this sputtering system are rf power input, gas pressure, plasma current, and target-to-substrate distance. Because a knowledge of the deposition rate is necessary to control film thickness and to evaluate optimal conditions which are an important consideration in preparing better thin films, the deposition rates of copper as a testing material under the various sputtering conditions are investigated. Furthermore, a triode sputtering system designed in our team is simulated by the SIMION program. As a result, it is sure that the simulation of electron trajectories in the sputtering system is confined directly above the target surface by the force of E${\times}$B field. Finally, some teats with the above 4 different sputtering conditions demonstrate that the deposition rate of rf triode magnetron sputtering is relatively higher than that of the conventional sputtering system. This means that the higher deposition rate is probably caused by a high ion density in the triode and magnetron system. The erosion area of target surface bombarded by Ar ion is sputtered widely on the whole target except on both magnet sides. Therefore, the designed rf triode magnetron sputtering is a powerful deposition system.

• Nuclear Engineering and Technology
• /
• v.37 no.4
• /
• pp.375-384
• /
• 2005

To investigate the flow-accelerated corrosion (FAC) dependency of carbon steel (A106 Gr. B) and low-alloy steels (1Cr-1/2Mo, 21/4Cr-1Mo) on pH, orifice distance, and material, experiments were carried out. These experiments were performed using a flow velocity of 4 m/sec (partly 9 m/sec) at pH $8.0\~10.0$ in an oxygen-free aqueous solution re-circulated in an Erosion-Corrosion Test Loop at $130^{\circ}\;{\ldots}$ for 500 hours. The weight loss of the carbon steel specimens appeared to be positively dependent on the flow velocity. That of the carbon and low-alloy steel specimens also showed to be distinguishably dependent on the pH. At pH levels of $8.0\~9.5$ it decreased, but increased from 9.5 to 10.0. Utility water chemistry personnel should carefully consider this kind of pH dependency to control the water system pH to mitigate FAC of the piping system material. The weight loss of the specimens located further from the orifice in the distance range of $6.8\~27.2$ mm was shown to be greater, except for 21/4Cr-1Mo, which showed no orifice distance dependency. Low alloy steel specimens exhibited a factor of two times better resistance to FAC than that of the carbon steel. Based on this kind of FAC dependency of the carbon and low-alloy steels on the orifice distance and material, we conclude that it is necessary to alternate the composition of the secondary piping system material of NPPs, using low-alloy steels, such as 21/4Cr-1Mo, particularly when the system piping has to be replaced.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.5
• /
• pp.817-823
• /
• 2020

In recent, the machining of difficult-to-cut materials such as titanium alloys, stainless steel, Inconel, ceramic, glass, and carbon fiber reinforced plastics (CFRP) used in aerospace, automobile, medical industry is actively researched. Abrasive waterjet is a non-traditional processing method in which ultra-high pressure water and abrasive particles are mixed in a mixing chamber and shoot out jet through a nozzle, and removed by erosion due to collision with a material. In particular, the nozzle of the abrasive waterjet is one of the most important parts that affect the machining quality as with a cutting tool in general machining. It is very important to monitor the condition of the nozzle because the workpiece is uncut or the surface quality deteriorates due to wear, expanding of the bore, damage of the nozzle and clogging of the abrasive, etc. Therefore, in this paper, we propose a monitoring system based on Acoustic Emission(AE) sensor that can detect nozzle condition in real time during AWJ processing.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.1
• /
• pp.73-80
• /
• 2016

The preliminary test for the dual mode plasma torch system was carried out to explore the operation properties in advance. The dual mode plasma torch system that is able to operate in transferred, non-transferred, or dual mode is very adequate for melting the mixed wastes including nonconductive materials such as concrete, asbestos, etc. since it exploits both the high efficiency of heat transfer to the melt in transferred mode and stable operation in non-transferred mode. Also, system operation including restarting is reliable and very easy. A stationary melter with a refractory structure was designed and manufactured considering the melting behavior of slags to minimize the refractory erosion. The power supply for the dual mode plasma torch system built with high power insulated gate bipolar transistor (IGBT) modules has functions for both current control and voltage control and is sufficient to suppress the harmonics during the operation of the plasma torch. The power supply provides two different voltages for transferred operation and non-transferred. It is confirmed that the operation voltage in transferred is always higher than non-transferred. The dual mode plasma torch system was successfully developed and is under operation for a melting experiment to optimize operation data.