• 한국지하수토양환경학회지:지하수토양환경
• /
• 제20권1호
• /
• pp.19-27
• /
• 2015

If $CO_2$ stored for geological sequestration escapes from deep formations and is introduced to shallow aquifers, it dissolves into groundwater, creates acidic environments, and enhance mineral dissolution from rocks and soils. Among these minerals, dissolution and spread of hazardous trace metals can cause environmental problems with detrimental impacts on groundwater quality. This study aims to investigate geochemical effects of $CO_2$ in groundwater on dissolution of galena, the main mineral controlling the mobility of lead. A series of batch experiments are performed with granulated galena in $CO_2$ solutions under various experimental conditions for $CO_2$ concentration and reaction temperature. Results show that dissolution of galena is significantly enhanced under acidic environments so that both of equilibrium concentrations and dissolution rates of lead increase. For thermodynamic analysis on galena dissolution, the apparent rate constants and the activation energy for galena dissolution are calculated by applying rate law to experimental results. The apparent rate constants are $6.71{\times}10^{-8}mol/l{\cdot}sec$ at $15^{\circ}C$, $1.77{\times}10^{-7}mol/l{\cdot}sec$ at $25^{\circ}C$, $3.97{\times}10^{-7}mol/l{\cdot}sec$ at $35^{\circ}C$ and the activation energy is 63.68 kJ/mol. The galena dissolution is suggested to be a chemically controlled surface reaction, and the rate determining step is the dissociation of Pb-S bond of surface complex.

• 한국광물학회지
• /
• 제9권2호
• /
• pp.55-63
• /
• 1996

Epidote occurs as veinlets in the propylitic alteration zone of the Bobae clay deposit, Pusan, Korea. Its cell parameters apparently decrease with the contents of Al, Fe, and Ca. Fourier transform infrared (FTIR) spectra show one hydrosyl environment related to AlM2 at 3357-3358 cm-1. In the mid-infrared region, the peaks at 950 and 1030 cm-1 sharper with increasing Al shifting to higher energy region. The peak at 885 cm-1 shifts slightly to a lower energy region with a decreasing intensity as the Fe content increases. In the far-IR region, epidote exhibits absorption bands at 120 and 140 cm-1, which are related to the Ca-O bonds in A-sites.M ssbauer spectra of epidote show that the isomer shifts of Fe3+ range from 0.36-0.37 at the M3 site and from 0.35-0.44 at M1 site. Fe2+ shows the isomer shift ranging from 1.11 to 1.13. Quadrupole splitting is 2.04 for Fe3+M3, 0.52-0.70 for Fe3+M1, and 2.61-2.70 for Fe2+M3. Calculation shows Fe3+M386-90.7%, Fe3+M12.5-3.6%, and Fe2+M35.8-11.4% of total iron, showing preferential distribution of Fe3+ in the M3 site. The Fe3+M3 content is between 0.486 and 0.513 per formula unit. in the Fe-rich epidote, less Fe3+ and more Fe2+ are accommodated in the M1 and M3 sites. Hence, the overall disorder increases as total Fe content increase. The ordering parameter of the Bobae epidote is 0.93-0.95, suggesting a disequilibrium state below 200$^{\circ}C$. The constant temperature over a long period may be essential for the transition from disordered state to equilibrium state, despite the possible variation in flux and composition of the hydrothermal fluid.

• 한국자동차공학회논문집
• /
• 제23권2호
• /
• pp.199-207
• /
• 2015

Solid materials of ammonia sources with SCR have been considered for the application of lean NOx reduction in automobile industry, to overcome complex problems of liquid urea based SCR. These solid materials produce ammonia gas directly with proper heating and can be packaged by compact size, because of high volumetric ammonia density. Among ammonium salts and metal ammine chlorides, calcium ammine chloride was focused on this paper due to low decomposition temperature. In order to make calcium ammine chloride in lab-scale, simple reactor and glove box was designed and built with ammonium gas tank, regulator, and sensors. Basic test conditions of charging ammonia gas to anhydrous calcium chloride are chosen from equilibrium vapor pressure by Van't Hoff plot based on thermodynamic properties of materials. Synthetic method of calcium ammine chloride were studied for different durations, temperatures, and pressures with proper ammonia gas charged, as a respect of ammonia gas adsorption rate(%) from simple weight calculations which were confirmed by IC. Also, lab-made calcium ammine chloride were analyzed by TGA and DSC to clarify decomposition step in the equations of chemical reaction. To understand material characteristics for lab-made calcium ammine chloride, DA, XRD and FT-IR analysis were performed with published data of literature. From analytical results, water content in lab-made calcium ammine chloride can be discovered and new test procedures of water removal were proposed.

• 한국어병학회지
• /
• 제1권2호
• /
• pp.131-134
• /
• 1988

어류에 의한 물과 멱이로부터의 물질 흡수를 연구하기 위하여 방사성 동위원소를 추적자로 이용하였다. 금붕어가 들어있는 네개의 수조에 Co-57을 처리한 후 각기 다른 온도 조건하에서 실험을 실시하였고, 또 다른 네개 수조의 어류는 동위원소를 처리한 먹이를 주었다. 실험결과로부터 수온은 물로부터의 코발트 흡수에 거의 영향을 미치지 않는 것으로 나타났다. 물에 동위 원소를 처리한 후 13일째 어류가 흡수한 코발트의 양은 총가용량의 0.0006%에 불과해 물을 통한 흡수과정은 매우 서서히 진행됨을 알 수 있었다. 먹이를 통해 어류체내에 흡수된 방사능은 90일간의 실험기간에 걸쳐 시간경과에 따라 선형 증가 양상을 보였으며, 실험 개시 후 90일째에 마리당 투여한 총 방사능의 12% 수준에서 거의 평형상태에 도달하였다.

• 대한화학회지
• /
• 제27권4호
• /
• pp.287-293
• /
• 1983

자유라디칼 개시제에 의한 디에틸 ${\alpha}$-페닐비닐 인산(DEPVP)과 아크릴로니트릴(AN) 및 말레산 무수물(MAnh)의 혼성중합 연구를 행하였다. 개시제로는 과산화벤조일을 사용하였으며 중합온도는 $70^{\circ}C$이었다. 단위체 반응성비는$ r_1(AN) = 0.77, r_2(DEPVP) = 0.002 $이었으며, 이 값으로 부터 DEPVP의 Alfrey-Price 상수 Q=0.012, e=-1.35를 얻었다. 이와 대조적으로 DEPVP와 MAnh와의 자유라디칼 혼성중합은 과산화 벤조일을 개시제로 사용하여 $70^{\circ}C$에서 클로로포름 용액중에서 행한 결과 초기 단위체의 농도비에 무관하게 1 : 1 교대 혼성 중합체를 형성하였으며, 두 단위체의 몰비가 MAnh / DEPVP = 7 / 3일때 중합속도가 최대였다. 핵자기 공명 분광법으로 구한 DEPVP와 MAnh의 전하이동 착물의 평형상수는 $21^{\circ}C$ 클로로포름 용액에서 0.085 l/mol이었다. 혼성 중합체중 DEPVP의 함량이 증가함에 따라 AN/DEPVP 쌍에서는 환산점성도가 감소함을 보였고 MAnh/DEPVP쌍에서는 변화가 별로 없었다

• 태양에너지
• /
• 제15권3호
• /
• pp.29-38
• /
• 1995

본 연구는 화학열펌프 개발을 목적으로 비교적 고온영역에서 화학축열에 응용 가능 할 것으로 판단되는 무기수화물계 $Ca(OH)_2/CaO$ 가역 반응싸이클을 이용한 수화 탈수반응에 따른 충진층내 열이동에 대하여 실험적 검토를 행하였다. 그 결과 본 실험에서 얻은 열교환특성은 $Ca(OH)_2$ 열분해 탈수반응시 반응기 내의 시료층 상단부가 하단부에 비해 탈수반응이 느리게 진행되었으며 이러한 현상은 탈수반응이 하부에서 상부로 진행됨을 알 수 있었다. 또, 반응기내 반경방향에서의 $Ca(OH)_2$ 열분해 탈수반응에 따른 온도변화는 시료 중심부에서 상 하단부로 나타났으며 이는 열전도도에 의한 온도 강하로 중심부의 축열온도가 높음을 알 수 있었다.

• 대한기계학회논문집B
• /
• 제29권3호
• /
• pp.390-401
• /
• 2005

In this study, extinction limit extension of unsteady $(CH_{4}+N_{2})$/air diffusion flames was investigated experimentally. A spatially locked flame in an opposing jet burner was perturbed by linear velocity variation, and time-dependent flame luminosity, transient maximum flame temperature and OH radical were measured over time with the high speed camera, Rayleigh scattering method and OH laser-induced fluorescence, respectively. Unsteady flames survive at strain rates that are much higher than the extinction limit of steady flames, and unsteady extinction limits extend as the slope of the strain rate increases or the initial strain rate decreases. We verified the validity of the equivalent strain rate concept by comparing the course of unsteady extinction process and steady extinction process, and it was found that the equivalent strain rate concept represents well the unsteady effect of a convective-diffusive zone. To investigate the reason of the unsteady extinction limit extension, we subtracted the time lag of the convective-diffusive zone by using the equivalent strain concept. Then the modified unsteady extinction limits become smaller than the original unsteady extinction limits, however, the modified unsteady extinction limits are still larger than the steady extinction limits. These results suggest that there exist the unsteady behavior of a diffusive-reactive zone near the extinction limit due to the chemical non-equilibrium states associated with unsteady flames.

• 한국생활과학회지
• /
• 제21권4호
• /
• pp.791-803
• /
• 2012

This study intends to identify applicability of natural dye extracted from Aplysia kurodai, aiming to standardization of Aplysia kurodai natural dyeing through scientific validation by analyzing characteristics of pigment elements to review dyeability, colorfastness and antibacterial activity. Such material as silk fabrics that is animal fiber were used for this purpose, and derived following summarized results. UV/VIS spectrum analysis on the pigment of Aplysia kurodai that was extracted from purple gland showed that maximum absorbtion was near 540 nm. The silk fabric optimal dyeing can be achieved at a temperature of $55^{\circ}C$ with a colorant concentration of 5%. Dyed at $55^{\circ}C$ with interval of 10~90 minutes for identifying dye uptake over time to observed slow increase of dye uptake over time, and equilibrium occurred at 50 minutes. For dye uptake according to pH, while dye uptake was superior in acidity, it decreased rapidly in a base after pH 7. For color changes according to pH variation, it was reddish purple in acidity and was purplish red in a base. For color changes according to mordanting method, more clear color change had been obtained when process with aluminium pre-mordanting than non-mordanting and post-mordanting. The colorfastness to light, perspiration and washing was 1, 4~5, and 3~4 ratings respectively. The silk fabric dyed with Aplysia kurodai demonstrated excellent antimicrobial activity to Staphylococcus aureus and Klebsiella pneumoniae. The Aplysia kurodai can be used as a new colorant for the natural dyeing of silk.

• Journal of Korean Society for Atmospheric Environment
• /
• 제14권E호
• /
• pp.9-17
• /
• 1998

Oxides of nitrogen play important roles in atmospheric chemistry. Soil has been recognized as a major natural source of NO, and its emission depends on soil parameters such as soil nitrogen availability, soil moisture and temperature. It is necessary to understand effects of these controlling parameters on soil NO emission. In order to understand soil moisture effects on NO emission, variations of NO concentration and existence of its equilibrium concentration were observed from ammonium fertilized Japanese upland soil prepared for different soil moisture conditions. The closed chamber technique was employed for this study. The significant increases in NO with soil moisture were found. Maximum was occurred at sample ID4 (55% of water-filled pore space (WFPS)), but it decreased as soil moisture increased. No significant NO concentration was emitted from soil sample without fertilizer, but there was significant NO in fertilized soil samples. The magnitudes of NO from soil increased with time and reached at steady state within ten minutes approximately. These results suggest that nitrogen input from fertilizer takes charge in the first step of sharp increase in NO emission, and then soil moisture becomes important factor to control NO emission from the soils. NO concentrations from soil were compared to those one-day after the experiment. Results from the comparison analysis suggest that the soil NO flux might have been stimulated by soil disturbances like mixing, and this is much more effective in dry soils rather than in wet soils. It was found that much less NO came out from soils after a day; suggesting that most of NO was released from the soils within a day after fertilizer application during our experiment. The length of NO releasing time span may depend on the amounts of fertilizer applied, soil moisture condition, and other soil physical parameters.

• 한국결정성장학회지
• /
• 제9권5호
• /
• pp.516-520
• /
• 1999

유형성 볼밀을 사용하여 순수한 철분말 암모니아가스 분위기 중에서 기계적 합금화(MA) 처리를 하였다. 그 결과 질소함량이 23 at% 까지 준안정 질화철 분말을 얻을 수 있었다. 질화철 분말의 생성상은 질소 함량이 14.5 at% N 이하의 경우 bcc과포화 고용체가, 20.8 at% N에서는 고온에서 안정한 비평형 hcp 결정 분말이었다. MA법으로 제조한 Fe-N계 분말의 포화 자화는 질소농도가 증가함에 따라 단조로운 감소를 보였으며 보고된 bct 질화철에서의 포화자화값 증가와 대조적인 결과를 나타냈다. 질소원자 주위의 상세한 를 조사하기 위하여 중성자 회절 실험을 행하였다. 그 결과, 9.5 at% N의 질화철 분말의 경우 질소원자 주위의 철원자의 배위수는 3.9이었으며, 이러한 결정구조해석 결과로부터 질소원자는 철원자로 이루어진 4면체의 중심에 위치하고 있는 것으로 판단되었다.