• Biomolecules & Therapeutics
• /
• v.14 no.4
• /
• pp.240-245
• /
• 2006

The primary use for glycidol is as a stabilizer in the manufacture of vinylpolymers, however, it is also used as an intermediate in the production of pharmaceuticals, as an additives for oil and synthetic hydraulic fluids, and as a diluting agent is same epoxy resins. In this study, we have carried out in vitro genetic toxicity test of glycidol and microarray analysis of differentially expressed genes in response to glycidol. The result of Ames test showed mutations with glycidol treatment in base substitution strain TA1535 both with and without exogenous metabolic activation. Likewise, glycidol showed mutations in frame shift TA98 both with and without exogenous metabolic activation. The result of COMET assay in L5178Y cells with glycidol treatment showed DNA damage both with and without exogenous metabolic activation. Glycidol increased micronuclei in CHO cells both with and without exogenous metabolic activation. 150 Genes were selected as differentially expressed genes in response to glycidol by microarray analysis and these genes would be candidate biomarkers of genetic toxic action of glycidol.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.6
• /
• pp.511-520
• /
• 2000

Ultrasonic pulse echo method comes to be difficult to apply to the multi-layered structure with very thin layer, because the echoes from the top and the bottom of the layer are superimposed. We can easily meet this problem when the silicon chip layer in the semiconductor is inspected by a SAM equipment using fairly low frequency lower than 20MHz by which severe attenuation in the epoxy mold compound of packaging material can be overcome. Conventionally, deconvolution technique has been used for the decomposition of superimposed UT signals, however it has disabilities when the waveform of the transmitted signal is distorted according to the propagation. In this paper, the wavelet transform based deconvolution(WTBD) technique is proposed as a new signal processing method that can decompose the superimposed echo signals with superior performances compared to the conventional deconvolution technique. WTBD method uses the wavelet transform in the pre-stage of deconvolution to extract out the common waveform from the transmitted and received signal with distortion. Performances of the proposed method we shown by through computer simulations using model signal with noise and we demonstrated by through experiments for the fabricated semiconductor sample with partial delamination at the top of silicon chip layer.

• Applied Chemistry for Engineering
• /
• v.3 no.3
• /
• pp.499-506
• /
• 1992

Copolymer of Styrene and GMA(glycidyl methachylate), having reactive ratios of $r_1=0.53$, $r_2=0.44$, was synthesized in dioxane using AIBN as free radical initiator. Followed by the reaction of ethylene diamine with copolymer PGS, amine groups were introduced to the PGS(NPGS). The composition of copolymer was determined by elemental analyzer. Poly(glycidyl methacrylate) (PGMA) was obtained in benzene using AIBN as free radical initiator. The NPGS-PGMA blend of 50/50 composition was prepared by mixing these polymers in THF at $65^{\circ}C$. Glass transition temperature (Tg) of NPGS-PGMA blend was measured by DSC. The blend showed a single Tg. Accordingly, it was clear that the NPGS was compatible with PGMA. An intermolecular reaction between amine groups of NPGS and epoxy groups of PGMA imparts compatibility in the NPGS-PGMA blend. When the NPGS-PGMA blend was added to the incompatible PS-PGMA blend, PS-PGMA blend showed Tg change. Scanning Electron Micrograph(SEM) showed a fine morphology in this blend. Consequently, it was apparent that the NPGS-PGMA blend acted as a compatibilizer for the PS-PGMA blend.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1997.11a
• /
• pp.130-137
• /
• 1997

Intumescent inorganic and organic coatings which dintr one from the other by the type of gas formers and the mechanisms of foam formation have been obtained and investigated. Inorganic intumescent coatings are the compositions based on water glass and mineral additives with different dispersity. Mineral additives contain adsorbed and absorbed water and carbonates which are destructed with the carbon dioxide and water evolution during the flame action on coating. The decreasing of mineral additives particle sizes under the mechanical milling with the fraction precipitation promotes the foam coke formation with less defects. Here the main structure of comparing compositions does not change. In organic coatings based on epoxy-polymers the polyammonium phosphate additive is used. It is the cabonization catalyst and the foam agent. The polyammonium phosphate of various dispersity employed is uniformly distributed on the polymeric matrix. The decreasing of the particle sizes leads to the increasing of the fire resistant properties of the intumescent coa-ting. The fire resistant analysis of the coating during more than an hour: the coating back side the temperature on plastic or wooden materials does not exceed 423K, and on metal-573K.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.3 no.3
• /
• pp.245-251
• /
• 1999

Carbon fibre reinforced plastic(CFRP) plate is one of the alternative materials for strengthening of reinforced and prestressed concrete members due to excellent strength and light weight. In this paper, the behavior of slabs strengthened with CFRP plate is observed and analyzed from the test results. Especially specimens with thick plate is tested when large moment and large shear force appear in same position. The failure mode is a peeling-off of the CFRP plate due to flexural-shear crack. This is observed near the loading points with thick plates. Because of this failure mode, thickness of CFRP plates does not influence on the failure loads. Depending on the loading pattern, it is necessary to consider different design criteria for reinforced concrete members with external reinforcement. When large moment and large shear force appear in same location, maximum thickness may limit to 0.6mm and ratio between moment of strengthened slab and moment of unstrengthened slab is proposed 1.5-2.0.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.5
• /
• pp.144-152
• /
• 2007

This study investigated the failure mechanism of RC beams strengthened with AFRP sheets. Total 5 half-scale RC beams were constructed and tested to estimate the effectiveness of various methods to prevent the debonding failure of AFRP sheets. From the experimental results, it was found that increasing bonded length or end U-wrappings does not prevent debonding failure. On the other hand, the beams with center U-wrappings and shear-keys reached the ultimate state with their sufficient performance. The center U-wrappings tended to control debonding of the longitudinal AFRP sheets because the growth of the longitudinal cracks along the edges of the composites was delayed. In case of shear-keys, it was sufficient to eliminate debonding and the beams failed by AFRP sheets rupture due to the sufficient bond mechanism.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.65-70
• /
• 2012

Glycidyl methacrylate (GMA) was used to introduce epoxy groups on the surface of polypropylene (PP) plate, used as a substrate, through plasma-induced graft copolymerization. Emulsion polymerization was applied for graft copolymerization of GMA and was compared with conventional solution polymerization to confirm its effect. Plasma treatment conditions under one atmospheric pressure were fixed as follows; the RF power of 200 W, the treatment time of 30 sec, the Ar gas flow rate of 6 LPM, and the exposure time of treated PP samples in air of 5 min. For graft-copolymerization, GMA concentration, reaction temperature, and reaction time was optimized to maximize the grafting degree of GMA. The maximum grafting degree of GMA was obtained at the condition of 12%-GMA concentration, $90^{\circ}C$ reaction temperature, and 5 hr-reaction time. Analysis results supported that the emulsion polymerization was more effective than the solution polymerization for grafting more GMAs on the surface of PP plate under the same reaction conditions.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.6
• /
• pp.979-983
• /
• 2008

Planar antennas are very efficient for the use of the out-door data transmission applications due to their low-profile characteristics. But the size of the antenna in UHF band blocks the practical usage. In this paper, a miniaturized planar antenna is investigated for the application of AMR system in UHF band. The designed antenna is fabricated in the form of the microstrip patch on the FR-4 substrate. The miniaturization is achieved by slot-loading on the patch. First, effects of simple slots on the size reduction are analyzed, followed by the design using more complex slots resulting in the reduction ratio of 37.9% in 425.6 MHz and bandwidth of 3.8 MHz. The effort of epoxy coating for the protection is also investigated.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.1
• /
• pp.50-58
• /
• 1998

Water vapor transmission was tested in water bath controlled by $20^{\cire}C$, 90%RH for T800/AD6005 based composite motor case which made by filament winding method. We detected internal relative humidity of composite motor case by inserting the humidity detector through the head of motor case for the study of humidity transmission through the wall of composite motor case. We found out that this composite material appears the water vapor flux of 2.88${\times}$$10^{-9}$g/$\textrm{m}^2$sec and diffusivity of 7.98${\times}$$10^{-7}$$\textrm{mm}^2$/sec at $20^{\cire}C$, 90%RH water vapor condition.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.2
• /
• pp.31-38
• /
• 2013

This research analyzed the acoustic emission signals collected from the pin loading tests and investigated the effect of hygrothermal exposure on the fracture behavior of the pin-jointed carbon fiber/epoxy composites. The composite specimens include: the Base specimen that has not been exposed to any environments, the RT specimen that has been immersed in room temperature water, and the HT specimen that has been immersed in high temperature water. According to the pin loading test, the RT and the HT specimens showed 2.2% and 13% decreases in the bearing strength compared to the Base specimen, respectively. The analysis of the acoustic emission signals showed different fracture acceleration points for three types of the specimens. Furthermore, for the RT and the HT specimens, the event from the matrix crack signals in the composites decreased. This shows the effect of the hygrothermal conditions on the acoustic emission signals. Additionally, upon investigating the fracture behaviors of the pin-jointed composites, the exposing specimens to hygrothermal environments decreases the interfacial characteristics of the composites.