• 한국환경보건학회지
• /
• 제25권3호
• /
• pp.103-107
• /
• 1999

Even if odorous compounds remain very low concentration in water, it cause strong odor. Because Geosmin and most of odorous compound had very low vaporization, those were difficult to analyze with GC/MSD and Purge & Trap. So, we needed pre-treatment method for decreasing amounts of extracting solvents, improving recovery efficiencies and increasing analytical efficiencies. This study developed efficient technology for analyzing odorous compounds, using various adsorbents and extracting solvents. The optimum adsorbent was XAD resins. Especially, XAD-2, XAD-7 and XAD-2010 were superior, but XAD-2 of these and the optimum extraction solvent is MTBE. Other extraction solvents' efficiency is in order of MTBE>Dichloromethane>n-Hexane>Diethylether. The optimum NaCl dosage for increasing efficiency is 5 g in liquid-liquid extraction method. The shaking time(0~24hr) has no concern with adsorption efficiency. The optimum adsorbent is XAD-2 resin and extraction solvent is MTBE. Dosing NaCl, adsorption efficiency is increased in liquid-liquid extraction method, but NaCl has no effect on liquid-solid extraction method. In this experimental results, this algae toxins(Mycrocystin, Anatoxin etc.).

• 한국입자에어로졸학회지
• /
• 제13권1호
• /
• pp.17-23
• /
• 2017

In this study, the test results obtained from the performance tests for CA (Korea Association of Cleaning Air) certificated air cleaners which had been commercially available in Korea from 2003 to 2015 were analyzed. Among the test parameters such as flow rate, particle collection efficiency, clean air delivery rate (CADR), ozone emission, odor removal efficiency and noise level, noise level and CADR were correlated with flow rates. Collection and odor removal efficiencies were 20% higher than the limit of the CA certification. The ozone emissions from the air cleaners were negligible because all the air cleaners were equipped with only HEPA filters, not electrostatic precipitation method which produces ozone.

• 한국환경과학회지
• /
• 제10권5호
• /
• pp.351-358
• /
• 2001

The main purpose of this study was to investigate the characteristics of cylindrical electrostatic precipitator with centrifugal effect in viewpoints of pressure drip and collection efficiency, experimentally. The experiment was carried out for the analysis of current-voltage, pressure drop and collection efficiency with various experimental parameters such as the applied voltage, inlet velocity, inlet size and inlet type(upper and bottom), etc. In the results, the pressure drops were estimated as 27~54, $34~63mmH_2O$ for inlet size $15mm{\tiems}30mm$ and $30mm{\tiems}60mm$, respectively. The collection effeciencies were shown over 90% with the small inlet size($15mm{\tiems}30mm$) for the applied voltage 40kV, inlet velocity(15~21m/s), and 51~89% with the large inlet size ($30mm{\tiems}60mm$). Moreover, in the applied voltage 0kV and inlet size $15mm{\tiems}30mm$, the collection efficiency induced by centrifugal force was represented as about 35% with inlet velocity 15 - 21m/s.

• 한국입자에어로졸학회지
• /
• 제9권1호
• /
• pp.23-29
• /
• 2013

Inertial impaction type mist eliminators are the most effective instruments to separate mist from the gas. In this work, the effect of the horizontal chevron type mist eliminators is characterized experimentally. Droplet size distribution and evaluation of removal efficiency of the chevron type mist eliminators at different gas flows were investigated using an aerosol particle size analyzer and a portable aerosol spectrometer, respectively. The experimental investigations showed that the mist removal efficiency in these instruments is dependent in the droplet size, and the pressure drop is nil.

• Membrane and Water Treatment
• /
• 제14권1호
• /
• pp.47-54
• /
• 2023

In this study, high concentrations of cadmium-containing wastewater were treated by electrodialysis (ED) with a channel stack. The limiting current density (LCD), cadmium removal efficiency, and current efficiency were investigated under each experimental condition according to the Reynolds number (Re), membrane area, and pH. With the increase in the film area to 111, 333, 555, and 777 cm² at Re (109.1), LCDs decreased to 408.11, 44.45, 35.32, and 13.64 A/m², respectively. The highest cadmium removal efficiency (99.6%) and current efficiency were obtained for the membrane area of 111 and 777 cm², respectively. Under changing Re in the pH range of 1 to 4, Re and LCD were proportional under the same pH condition, and pH and LCD tended to be inversely proportional under the same Re condition. Cadmium removal rate was the best at the pH range 3 - 4. It has been found that ED with channeled stacks can be successfully applied to treat wastewater containing high concentrations of cadmium.

• Membrane and Water Treatment
• /
• 제15권1호
• /
• pp.1-9
• /
• 2024

Biological nutrient removal is gaining increasing attention in wastewater treatment plants; however, it is adversely affected by low temperatures. This study examined temperature effects on nutrient removal and morphological stability of the granular and denitrifying phosphorus accumulating organisms (PAO and DPAO, respectively) using sequencing batch reactors (SBRs) at 5, 10, and 20 ℃. Lab-scale SBRs were continuously operated using anaerobic-anoxic and anaerobic-oxic cycles to develop the PAO and DPAO granules for 230 d. Sludge granulation in the two SBRs was observed after approximately 200 d. The average removal efficiency of soluble chemical oxygen demand (SCOD) and PO₄^3--P remained >90% throughout, even when the temperature dropped to 5 ℃. The average removal efficiency of NO₃^--N remained >80% consistently in DPAO SBR. However, nitrification drastically decreased at 10 ℃. Hence, the removal efficiency of NH₄⁺-N was decreased from 99.1% to 54.5% in PAO SBR. Owing to the increased oxygen penetration depth at low temperatures, the influence on nitrification rates was limited. The granule in DPAO and PAO SBR was observed to be unstable and disintegrated at 10 ℃. In conclusion, morphological characteristics showed that changed conversion rates at low temperatures in aerobic granular sludge altered both nutrient removal efficiencies and granule formation.

• 자원ㆍ환경경제연구
• /
• 제11권3호
• /
• pp.345-375
• /
• 2002

The purpose of this paper is to measure the change of the production efficiency which may happen when environmental regulation incurs technological constraint in the process of production, and to compute the opportunity cost of pollution reduction with the lost products based on the change of efficiency. The patterns of production technoloy in the paper are divided into the technologies of strong disposability and weak disposabilty to grasp the effect of the technological constraint due to the environmental regulation. The endowment of the technolgical constraints in the process of production is considered to bring the greatest restriction on firm's production. When the environmental efficiencies of Korean regional manufactures were measured with linear programming model, the lost products related with the constraint of production technology that environmental regulation incurred, was average 148.1 billion dollar per year(5.87% of one year overall products) for total manufactures in 1991~1998. The ratio of the lost products for total products was spread from 0.78% to 1l.08%. The average lost products of 15 regions were changed from 4.66% to 18.35% of total products. Generally the environmental efficiency index of regional manufactures being decreased continuously since 1991, it is estimated that the environmental performance of Korean manufactures has been more and more deteriorating.

• 한국산업보건학회지
• /
• 제15권1호
• /
• pp.36-44
• /
• 2005

A push pull hood system is frequently applied to control contaminants evaporated from an open surface tank in recent years. Efficiency of push pull hood system is affected by various parameters, such as cross draft, vessel shapes, size of tanks surface, liquid temperature, and so on. Among these, velocity of cross draft might be one of the most influencing factor for determining the ventilation efficiency. To take account of the effect of cross draft velocities over 0.38m/s, a flow adjustment of ${\pm}$20% should be considered into the push and +20% into the pull flow system Although there are many studies about the efficiency evaluation of push pull hood system based on CFDs(Computational Fluid Dynamics) and experiments, there have been no reports regarding the influence of velocities and direction of cross-draft on push-pull hood efficiency. This study was conducted to investigate the influence of cross draft direction and velocities on the capture efficiency of the push-pull ventilation system. Smoke visualization method was used along with mock-up of push-pull hood systems to verify the ventilation efficiency by experiments. When the cross-draft blew from the same origins of the push flows, the efficiency of the system was in it's high value, but it was decreased significantly when the cross-draft came from the opposite side of push flows Moreover, the efficiency of the system dramatically decreased when the cross-draft of open surface tank was faster than 0.4m/s.

• 환경위생공학
• /
• 제12권1호
• /
• pp.39-48
• /
• 1997

The study was conducted to know the possibility that the removal efficiency of organic and suspended solids(SS) could be increased by suppling of sea water and the optimum amount of sea water to be supplied treat bleaching waste water by lime coagulation settlement at pulp mill process. When the lime dosage was increased, the removal efficiency of COD and SS in the waste water was increased based on the removal efficiency of COD and SS. The lime dosage and removal efficiency was increased proportionally with the lime concentration of 4,000 mg/l, but the increase of removal efficiency was presented slightly above the 4,000mg/l. It was evaluated that the removal efficiencies of COD and SS could be increased and the requirement of lime dosage could be decreased by the sea water supplement. The removal efficiency of SS was most increased when the sea water supplement was 10% or more in the waste water. The removal efficiencies of COD was the best at 4% sea water excepting the dilution efficiency by sea water supplement.

• 환경위생공학
• /
• 제24권3호
• /
• pp.7-15
• /
• 2009

본 연구에서는 DEPHANOX공정을 변형한 두 개의 질산화 반응조를 둔 M-DEPHANOX 공정과 기존 변형된 질산화 반응조를 RBC로 대체한 형태로 단일 질산화 반응조로 운전된 M-DEPHANOX 공정을 운전하였다. 그리고 두 공정의 제거율을 비교하기 위하여 질소, 인 및 유기물 제거율과 질산화 반응조의 유기물 부하에 따른 $NH_3$-N 제거율을 조사하였다. 연구결과 $NH_3$-N 제거율은 M-DEPHANOX공정이 91.8%, M-eBNR 공정은 96.9%로서 두 공정 모두 높게 나타났다. TCOD와 SCOD 제거율은 M-DEPHANOX공정은 84.1와 78.2%, M-eBNR공정은 83.4%와 75.6%이었다. 또한 유기물이 $NH_3$-N 제거율에 미치는 영향은 M-eBNR 공정의 질산화 반응조에서는 1차 침전조에서 거의 나타나지 않았다. M-eBNR 공정의 $NH_3$-N 제거율은 도시하수의 유입성상이 달라지더라도 안정적으로 유지되었다.