• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of KIISE:Information Networking
• /
• v.28 no.2
• /
• pp.262-276
• /
• 2001

Recently much research for developing forwarding table that support fast router without employing both special hardware and new protocols. This article introduces a new forwarding data structure based on the software to enable forwarding lookup to be penormed at giga-bit speed. The forwarding table is known as a bottleneck of the routers penormance due to its high complexity proportional to the forwarding table size. The recent research that based on the software uses a Patricia trie and its variants. and also uses a hash function with prefix length key and others. The proposed forwarding table structure construct a forwarding table by the bit stream array in which it constructs trie from routing table prefix entries and it represents each pointer pointing the child node and the associated forwarding table entry with one bit The trie structure and routing prefix pointer need a large memory when representing those by linked-list or array. but in the proposed data structure, the needed memory size is small enough since it represents information with one bit. Additionally, by use a lookup method that start searching at desired middle level we can shorten the search path. The introduced data structure. called bit-map trie shows that we can implement a fast forwarding engine on the conventional Pentium processor by reducing the backbone routing table fits into Level 2 cache of Pentium II processor and shortens the searching path. Our experiments to evaluate the performance of proposed method show that this bit-map trie accomplishes 5.7 million lookups per second.

• Journal of Korean Society of Transportation
• /
• v.35 no.4
• /
• pp.321-331
• /
• 2017

The objective of this study is to analyze the factors affecting the pedestrian accidents of roundabout near schools. To this end, this study has focus on the comparative analysis of pedestrian accidents across different school areas. The traffic accident data from 2007 to 2014 are collected from TAAS data set of Road Traffic Authority. To develop the pedestrian accident rate model, the linear regression model has been utilized in this study. 28 explanatory variables such as geometry and traffic volume factors are used. The main results are summarized as follows. First, the null hypotheses that the number of pedestrian accidents are the same are rejected. Second, 5 multiple linear regression accident models with higher statistical significance (adjusted $R^2$ of 0.651~0.788) have been developed. Third, while the common variables of 3 models (model I~III) related to school location are evaluated to be the pedestrian island, crosswalk, types of roundabout, elementary school and bus stop. Fourth, while the common variable of 3 models (model III~V) related to near school area or not is evaluated to be pedestrian island, type of roundabout, sidewalk, elementary school, speed hump, speed limit sign and number of entry lane. As a result, the installation of pedestrian islands and crosswalk might be expected to decrease the number of pedestrian accidents near schools.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.1
• /
• pp.37-46
• /
• 2004

In order to increase fishing efficiencies of the fyke net used in the coast of Jeju Island, water tank experiment was caried out entering and escaping behavior using nets that were reduced to 1/20 of the size of the full scale fyke net and were improved to have antrance structure, and mackerel Scomber japonicus as experimental fish. The results of measurement are as follows : 1. Fish school behavior in the main net was showed two different patterns : swimming in a circle in the right space of the main net and swimming back and forth in ellipse in the right and left space. 2. The swimming speed of mackerel school was 23.9. 12.6 and 32.0cm/sec in the center space, right space of main net and in the mouth 3. The entering rate of fish school was 40% in net with 35cm length of the upper and funnel net in the mouth of fyke model net and 49% in conventional type fyke model net. 4. The escaping rate of fish school was 10% in net with 35cm length of the upper and funnel net in the mouth of fyke model net and 69% in conventional type fyke model net. 5. The remain rate of fish school was 90% in net with 35cm length of the upper and funnel net in the mouth of fyke model net and 31% in conventional type fyke model net.

• Korean Journal of Remote Sensing
• /
• v.38 no.6_1
• /
• pp.1015-1023
• /
• 2022

The Entry-Descent-Landing process of a lander involves many environmental and technical challenges. To solve these problems, recently, terrestrial relative navigation (TRN) technology has been essential for landers. TRN is a technology for estimating the position and attitude of a lander by comparing Inertial Measurement Unit (IMU) data and image data collected from a descending lander with pre-built reference data. In this paper, we present a method for generating descent dataset and extracting landmarks, which are key elements for developing TRN technologies to be used on Mars. The proposed method generates IMU data of a descending lander using a simulated Mars landing trajectory and generates descent images from high-resolution ortho-map and digital elevation map through a ray tracing technique. Landmark extraction is performed by an area-based extraction method due to the low-textured surfaces on Mars. In addition, search area reduction is carried out to improve matching accuracy and speed. The performance evaluation result for the descent dataset generation method showed that the proposed method can generate images that satisfy the imaging geometry. The performance evaluation result for the landmark extraction method showed that the proposed method ensures several meters of positioning accuracy while ensuring processing speed as fast as the feature-based methods.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.6
• /
• pp.457-462
• /
• 2022

Recently, a variety of cultural life using drones as an entertainment tool has been created, and in order to realize this, more and more users are using drones with good performance enough to invade the no-flight zone. Drones for satisfying entertainment activities must have long flight times and be able to fly long distances, which can often cause great damage by invading no-flight zones or causing unwanted flight crashes. In this study, in order to solve this problem, a no-flight zone is set with GCS(Ground Control System), and when flying at a critical speed of 10km/h or less, the drone is safely operated by not entering the critical distance 10m away from the no-flight zone, and the critical speed A method was proposed to prevent the drone from entering the no-flight zone by allowing the drone to self-drop by GCS control when it flies beyond the threshold and enters the critical distance. As a result of a total of 44 repeated experiments in a specific experimental area with the proposed method, the drone safely self-dropped except for the case where it crossed the restricted area once or twice. It was found to be an appropriate way to prevent this.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.4
• /
• pp.268-281
• /
• 2004

A study was carried out in order to estimate the deformation of the pound net according to the current by the model test in the circulating water channel. The tension of the frame rope and the variation of net shape were measured to investigate the deforming of the model pound net in the flow. The results are obtained as follows; 1. The experimental equation between tensions (R) of the frame rope and velocity (ν)was found to be R=$19.58v^{1.98}$($r^2$=0.98) in case of the upperward flow with fish court net and R=$26.90v^{1.72}$($r^2$=0.95)at the upperward flow with bag net according to the velocity from 0.0m/s to 0.6m/s, respectively. 2. As the variation of flow speed inside of the model net was gradually decreased according as which is passed through netting panels, in case of the upperward flow with fish court net, the flow speed was about 70% of initial flow speed at 0.1m/s, 60% at 0.2m/s, 50% at 0.3m/s and 40% 0.4~0.6m/s at the measurement point(h) inside of the first bag net, respectively. In case of the upperward flow with bag net, as the flow speed was steeply decreased according as which if passed through the second bag net, it was 30~60% of the initial flow speed and was 20~30% inside of the first bag net and was about 10~20% inside of the inclined passage net. 3. In case of the upperward flow with fish court net, the variation of deformed angle of fish court net was from 0$^{\circ}$ to 70$^{\circ}$and that of inclined passage net was from 0$^{\circ}$ to 63$^{\circ}$and that of the second bag net was from 0$^{\circ}$ to 47$^{\circ}$ . 4. In case of the upperward flow with fish court net, the variation of deformed angle of the second bag net was changed from 0$^{\circ}$ to 70$^{\circ}$and that of the inclined passage net was from 0$^{\circ}$ to 55$^{\circ}$ and that of the fish court net was from 0$^{\circ}$ to 50$^{\circ}$. The depth ratio of the first bag net was changed from 0% to 35% and that of the second bag net was from 0% to 20% and that of the inclined passage net was from 0% to 35%. In the flow speed 0.5m/s, the inclined passage net was raised up to the entry of the bag net and then prevented it more over 90%. 5. To be increased the opening volume of pound net, it needs to attach the added weight outside of the fish court net, inclined passage net and bag net. At the same time, it needs to adjust the tension of the twine for maintenance of the shape.

• Journal of Korea Entertainment Industry Association
• /
• v.14 no.3
• /
• pp.191-200
• /
• 2020

Companies are seeking to maximize profits through exports and imports in the ultra-fast, ultra-high-speed modern society. It is only possible to sustain its survival if it targets the global market, not based on any specific region. The K-POP group is also targeting overseas markets in a manner similar to the various global strategies used when companies make inroads into foreign markets, including exports, contracts and direct investment. The K-POP group is engaged in various forms of activities, ranging from simple forms of performance (export) that are visited and staged by an invitation from a certain foreign country to series performances (license) by an invitation from a local promoter and tour performances using its capabilities. The K-POP group is seeking to go beyond the art of single-stage performances and make a systematic plan and make inroads into foreign countries in the form of direct investment suitable for each foreign country. The K-POP group made inroads into overseas markets in the form of simple performances from the late 1990s to 2005, when 'Korean Wave' was first introduced. Group H.O.T., etc. are typical examples. Since then, it has sought to enter overseas markets in the form of franchises by accepting overseas members by 2018, starting with Super Junior in 2005. Since then, the K-POP group in the form of joint investment attempted as group IZ*ONE in 2018 appeared, and a voice story came out in September 2018 when South Korea's JYP Entertainment and Tencent of China joined forces. Unlike K-POP Group, which has entered foreign markets with a global strategy based on the existing export method (H.O.T.), 'Boystory' is a representative group that is made with joint investment, which is a direct investment method. In February 2020, RBW released 'D1Verse,' a five-member group selected by Vietnam's reality show, as a joint investment-type group. This shows the possibility that domestic and foreign companies will release a group in the form of joint investment in order to pursue both globalization and localization.

• Fire Science and Engineering
• /
• v.30 no.2
• /
• pp.81-86
• /
• 2016

Recently, frequent traffic congestion has occurred in domestic urban roads. As a solution for downtown traffic congestion in domestic urban roads, plans for great depth underground double-deck tunnels have been made. Great depth underground double-deck tunnels that have been planned for passenger cars, has the structure of a network type; the entry of vehicles is carried out in the underground space. In these network great depth underground double-deck tunnels, the cross section and the height of the tunnel are smaller than the general road tunnel, and the smoke of a fire will propagate faster than the evacuation of tunnel passengers by the action of the traffic-ventilation and casualties are expected. Therefore, in the present study, an attempt was made to prevent the delay system for fire smoke diffusion at the time of a fire in a domestic network great depth underground double-deck tunnel according to the area of the tunnel block during the operation of the delay system for fire smoke diffusion to analyze the effects of reducing the inflow velocity. When the area of the tunnel block was not less than 50%, the effect of reducing about 21% of the wind speed acting on the tunnel was significant. If the area is more than 50%, the diffusion rate of fire smoke was reduced by approximately 21%, which will be useful for a safe evacuation.