• Journal of the Korean Electrochemical Society
• /
• v.18 no.2
• /
• pp.68-74
• /
• 2015

To compare the microstructure and electrochemical properties between two binary alloys (Cr-Si, Ni-Si), two composition of binary alloys with the same capacity were selected using phase-diagram and prepared by matrix-stabilization method to suppress the volume expansion of Si by inactive-matrix. Master alloys were made by Arc-melting followed by fine structured ribbon sample preparation by Rapid Solidification Process (RSP, Melt-spinning method) under the same conditions. Also powder samples were produced by wet grinding for X-Ray Diffraction (XRD) and electrochemical measurements. As predicted from the phase diagram, only active-Si and inactive-matrix ($CrSi_2$, $NiSi_2$) were detected. The results of Scanning Electron Microscope (SEM) and Transmission Electron Microscopy - Energy Dispersive X-ray Spectroscopy (TEM-EDS) show that Cr-Si alloy has finer microstructure than Ni-Si alloy, which was also predictable through phase diagram. The electrochemical properties related to microstructure were evaluated by coin type full- and half-cells. Separately, self-designed test-cells were used to measure the volume expansion of Si during reaction. Volume expansion of Cr-Si alloy electrode with finer microstructure was suppressed significantly and improved in cycle capability, in comparison Ni-Si alloy with coarse microstructure. From these, we could infer the correlation of microstructure, volume expansion and electrochemical degradation and these properties might be predicted by phase diagram.

• Journal of Powder Materials
• /
• v.20 no.1
• /
• pp.53-59
• /
• 2013

Fe-TiC composite powder was fabricated via two steps. The first step was a high-energy milling of FeO and carbon powders followed by heat treatment for reduction to obtain a (Fe+C) powder mixture. The optimal condition for high-energy milling was 500 rpm for 1h, which had been determined by a series of preliminary experiment. Reduction heat-treatment was carried out at $900^{\circ}C$ for 1h in flowing argon gas atmosphere. Reduced powder mixture was investigated by X-ray Diffraction (XRD), Field Emission-Scanning Electron Microscopy (FE-SEM) and Laser Particle Size Analyser (LPSA). The second step was a high-energy milling of (Fe+C) powder mixture and additional $TiH_2$ powder, and subsequent in-situ synthesis of TiC particulate in Fe matrix through a reaction of carbon and Ti. High-energy milling was carried out at 500 rpm for 1 h. Heat treatment for reaction synthesis was carried out at $1000{\sim}1200^{\circ}C$ for 1 h in flowing argon gas atmosphere. X-ray diffraction (XRD) results of the fabricated Fe-TiC composite powder showed that only TiC and Fe phases exist. Results from FE-SEM observation and Energy-Dispersive X-ray Spectros-copy (EDS) revealed that TiC phase exists uniformly dispersed in the Fe matrix in a form of particulate with a size of submicron.

• Journal of Hydrogen and New Energy
• /
• v.23 no.5
• /
• pp.429-436
• /
• 2012

Mg and Mg-based alloys are regarded as strong candidate hydrogen storage materials since their hydrogen capacity exceeds that of known metal hydrides. One of the approaches to improve kinetic is addition of metal oxide. In this paper, we tried to improve the hydrogenation properties of Mg-based hydrogen storage composites. The effect of transition metal oxides, such as $Nb_2O_5$ on the kinetics of the Magnesium hydrogen absorption kinetics was investigated. $MgH_x$-5wt.% $Nb_2O_5$ composites have been synthesized by hydrogen induced mechanical alloying. The powder fabricated was characterized by X-ray diffraction (XRD), Field Emission-Scanning Electron Microscopy (Fe-SEM), Energy Dispersive X-ray (EDX), BET and simultaneous Thermo Gravimetric Analysis / Differential Scanning Calorimetry (TG/DSC) analysis. The Absorption / desorption kinetics of $MgH_x$-5wt.% $Nb_2O_5$ (type I and II) are determined at 423, 473, 523, 573 and 623 K.

• Clean Technology
• /
• v.19 no.3
• /
• pp.320-326
• /
• 2013

Nano-sized PtRu-Ni/VC and PtRu-Sn/VC electrocatalysts were synthesized by a one-step radiation-induced reduction (RIR) (30 kGy) process using distilled water as the solvent and Vulcan XC-72 as the supporting material. The obtained electrocatalysts were characterized by transmission electron microscopy (TEM), scanning electron microscope energy dispersive spectroscopic (SEM-EDS), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), respectively. The catalytic efficiency of electrocatalysts was examined for oxygen reduction, MeOH oxidation and CO stripping decreased in the following order, Hydrogen stripping : PtRu-Sn/VC > PtRu-Ni/VC > PtRu/VC$^{(R)}$ (E-TEK). MeOH oxidation : PtRu-Sn/VC > PtRu-Ni/VC > PtRu/ VC$^{(R)}$ (E-TEK). Unit cell performance : PtRu-Sn/VC > PtRu-Ni/VC > PtRu/VC$^{(R)}$ (E-TEK) catalysts.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.295-295
• /
• 2010

Nanoparticles of the compound semiconductor, Cu(In, Ga)Se2 (CIGS), were synthesized in solution under ambient pressure below $100^{\circ}C$ and characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), optical absorption spectroscopy and energy-dispersive X-ray (EDX) analyses. These materials have chalcopyrite crystal structures and the particle sizes less than 100 nm. Synthetic conditions were studied for the crystallized CIGS nanoparticles formation to prevent from side products of Cu2Se, Cu2-xSe, and CuSe etc. The single phase CIGS nanoparticles were applied to coating of thin films photovoltaic cells. The electro deposition of CIGS thin films is also a good non-vacuum technology and under investigation. In aqueous solutions, the different chemical compositions of CIGS thin films were obtained, depending on pH, concentration of starting materials and deposition potentials. The surface morphology of the prepared CIGS thin films depends on the complexing ligands to the solutions during the electrochemical deposition.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.924-925
• /
• 1999

Bi-system high-$T_c$ superconductors with the nominal composition $(Bi_{0.7}Pb_{0.3})_2-Sr_{2}Ca_{2}Cu_{3}O_{x}$ have been prepared by PJL method. The critical temperature (offset temperature) of the sample annealed for 13 hours in air was 102K. And the results of X-ray diffraction(XRD) patterns, scanning electron microscope (SEM) images and energy dispersive X-ray (EDX) spectra analyses, it was found that PJL method is so effective to reduce the heat treatment period.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.107-107
• /
• 2015

In order to investigate electrochemical behavior and biocompatibility of Co-Cr dental alloy by electrochemical corrosion test and MTT assay, the xCo-25Cr-yW-zNi alloys were used in this study. Samples of Co-Cr-W-Ni alloys were manufactured using arc melting furnace. The microstructure of the alloys was examined by optical microscopy (OM), Field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), MTT assay, and corrosion test. Corrosion resistance increased slightly as cobalt (Co) content increased. And bioactivity was concerned with nickel (Ni) and tungsten (W). Biocompatibility of Co-Cr alloy depended on Ni and W contents.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.164-164
• /
• 2008

금속배선공정에서 높은 전도율과 재료의 값이 싸다는 이유로 최근 Cu를 사용하였으나, 디바이스의 구조적 특성을 유지하기 위해 높은 압력으로 인한 새로운 다공성 막(low-k)의 파괴와, 디싱과 에로젼 현상으로 인한 문제점이 발생하게 되었다. 이러한 문제점을 해결하고자, 본 논문에서는 Cu 표면에 Passivation layer를 형성 및 제거하는 개념으로 공정시 연마제를 사용하지 않으며, 낮은 압력조건에서 공정을 수행하기 위해, 전해질의 농도 변화에 따른 Liner sweep voltammetry 법을 사용하여 전압활성화에 의한 전기화학적 반응이 Cu전극에 어떤 영향을 미치는지 연구하였으며, 표면 조성을 알아보기 위하여 Energy Dispersive Spectroscopy (EDS) 분석을 하였고, Cu disk의 결정성과 배향성 관찰을 위해 X-Ray diffraction (XRD)로 금속 표면을 비교하여 실험 결과로 얻어진 데이터를 통하여 ECMP 공정에 적합한 전해액 선정과 농도를 선택하였다.

• Journal of Hydrogen and New Energy
• /
• v.19 no.6
• /
• pp.482-489
• /
• 2008

Ti-Cr alloys consist of BCC solid solution, C36, C14 and C15 Laves phase at high temperature. Among others, the BCC solid solution phase was reported to have a high hydrogen storage capacity. However, activation, wide range of hysteresis at hydrogenation/dehydrogenation, and degradation of hydrogen capacity due to hydriding/dehydriding cycles must be improved for its application. In this study, to improve such problems, we added a Nb. For attaining target materials, Ti-10Cr-xNb(x=1, 3, 5wt.%) specimens were prepared by arc melting. The arc melting process was carried out under argon atmosphere. As-received specimens were characterized using XRD(X-ray diffraction), SEM(Scanning Electron Microscopy) with EDX(Energy Dispersive X-ray) and TG/DSC(Thermo Gravimetric Analysis/Differential Scanning Calorimetry). In order to examine hydrogenation behavior, the PCI(pressure-Composition-Isotherm) was performed at 293, 323, 373 and 423K.

• Journal of the Korean Home Economics Association
• /
• v.41 no.8
• /
• pp.55-62
• /
• 2003

Natural dyes generally fan into two categories; organic dyes coming from animals and plants and inorganic dyes obtained from various minerals such as bengala, loess, ultramarine, prussian blue and etc. The main components of volcanic ash is clay mineral such as kaolinite, illite, quartz. Clay minerals Composing volcanic ash are kaolinite［$Al_4Si_4O_{10}{(OH)_{8}}$］, illite［$K_{X}Al_2(Si,\;Al)_4O_{10}{(OH)}_2$］, quartz［$SiO_2$］, homblende［$Na_{0-1}\;Ca_2{(Mg,\;Fe,\;Al)}_5{(Si,\;Al)}_{8}O_{22}{(OH)}_2$］and etc. And the redish color mainly comes from iron oxide. In this paper, two different classes of dyeing process were tested; dyeing with volcanic ash only and cationic agent pre-treatment followed by dyeing with volcanic ash. The compositions of the volcanic ash powder and the volcanic ash deposited on the cotton knitted fabrics identified by energy dispersive spectrometer and XRD analysis. The major chemical components of volcanic ash deposited on the cotton knitted fabrics were confirmed to be the saicon oxide, iron oxide, and aluminum oxide and etc. According to the analysis by XRD and EDS-SEM, kaolinite, illite and quartz were also identified.