• 에너지공학
• /
• 제23권1호
• /
• pp.1-6
• /
• 2014

본 에너지 분산 형 미세열량측정에 관한 자료는 에너지 분산 형의 우수한 조작 성을 유지하면서 파장 분산 형과 비슷한 정도의 에너지 분해능을 가질 수 있도록 개선한 것으로 광범위한 에너지의 X선을 검출을 할 수 있다. X선을 검출하기 위해서 이용되는 파장 분산 형은 에너지 분해능이 우수하지만 X선의 파장에 대해 검출 각도를 변화시켜야 하고 검출하고자 하는 특정 X선 종류에 따라 몇 가지의 검출기를 필요로 하고 있다. 그러나 에너지 분산 형의 검출기는 한 개의 검출기로 광범위한 X선을 동시에 검출할 수 있으며 조작 방법도 비교적 용이하다. 그러나 에너지 분산 형은 에너지 분해능이 우수하지 못 하고 또한 인접한 에너지를 갖는 X선은 그 피크가 중첩되어 구별하기가 어려운 경우도 있다. 에너지 분해능은 파장분산 형이 2~20 eV이고 에너지 분산 형은 140~180 eV로 상당한 차이가 있다.

• 한국산업보건학회지
• /
• 제23권3호
• /
• pp.205-211
• /
• 2013

Objectives: 21 sepiolite substances produced in China were investigated for the presence of asbestos in their materials. Materials and methods: In order to identify asbestos in sepiolite substances, test materials were analyzed using a transmission electron microscope equipped with energy dispersive X-ray spectrometer (TEM-EDS) for confirming their shape and components (atomic %). Results: Five of 21 sepiolte substances were asbestos-containing materials. Two chrysotile containing sepiolite proved to be asbestoscontaining materials, as did two chrysotile mixed with tremolite containing sepiolite. 16 sepiolite substances did not contain asbestos materials. Conclusions: When importing sepiolite substances, they must be analyzed to determine if there is asbestos in their materials.

• 자원환경지질
• /
• 제17권4호
• /
• pp.315-320
• /
• 1984

The newly discovered minerals found during 30 years have been discovered with election microprobe analysis, and several other new minerals have been described largely on the basis of probe analysis. Widely used types of instrument are the wavelength dispersive spectrometer (WDS) and the energy dispersive Spectrometer (EDS), with emitted X-ray dispersed by a curved crystal that is arranged to satisfy the Bragg equation ($n{\lambda}=2dsin{\theta}$). Atomic Nos of Z 4 to 92 can be analyzed quantitatively if they present in amount exceeding 50~100ppm. The application of the microprobe in mineralogical and geological research is quantitative chemical analysis of grains as small as a few microns in diameter, individual grains in a rock or can be analyzed in thin section and polished section, analysis can be made comparatively short time, methods in non-destructure, to photographical and crystallographical information. This paper was written in order to document data evaluation procedure for quantitative energy dispersive election probe analysis.

• 한국산업보건학회지
• /
• 제24권2호
• /
• pp.146-151
• /
• 2014

Objectives: Chrysotile is mineralogically distinct from amphiboles, displaying a notably different chemical structure. The thin sheets that form chrysotile fiber lead to the ability of the lung/macrophage system to decompose the chrysotile fibers. This study was performed in order to compare the physicochemical characteristics of Korean asbestos with those of Canadian amphiboles. Materials: An acid solubility test for each test substance was done to compare pH 4.5 and pH 1.2 distilled water. Asbestos fibers which had been placed in acid solutions for five days, five weeks and weeks were analyzed with a transmission electron microscope equipped with an energy dispersive X-ray spectrometer (TEM-EDS). Results: The composition element (Mg) of Korean chrysotile, Korean anthophyllite and Canadian amosite significantly decreased from 5 days and also decreased significantly after 5 weeks and 10 weeks. Only the composition (Mg) of Canadian crocidolite did not change under any conditions. From 5 days, the Mg of Korean chrysotile, Korean anthophyllite and Canadian amosite were significantly lower than before the acid treatment, but there were no changes over time or by the pH of the acid solutions. Particularly after 10 weeks, the composition (Mg) of Korean chrysotile in the pH 1.2 acid solution showed a rapid reduction of 15.86%. Conclusions: Korean chrysotile was very weak in an acid environment, beginning to show significant changes after 5 days. The Mg component rapidly decreased after 10 weeks in the pH 1.2 acid solution.

• 한국세라믹학회지
• /
• 제27권1호
• /
• pp.136-146
• /
• 1990

Whiskers of SiC were grown from the mixture of silica and graphite powders by Acheson method(direct heating method). The structrua, morphological and chemical characterizations have been performed by X-ray diffractometer(XRD), transmission electron microscopy(TEM), optical microscopy(OM), scanning electron microscopy(SEM), X-ray photoelectron spectroscopy(XPS) and energy dispersive spectrometer(EDS). The growth mechanism of SiC whiskers is also discussed.

• 한국환경과학회지
• /
• 제33권5호
• /
• pp.297-304
• /
• 2024

PM (Particulate Matters) was collected from a bag filter dust collector at an aluminum foundries, and its physicochemical properties were investigated using particle size analyzer and scanning electron microscopy with energy dispersive X-ray spectrometer (SEM/EDS). The median volume diameter of the particles passing through the pretreatment dust collector of the cyclone was approximately 10 ㎛. The cyclone pretreatment dust collector was shown to significantly reduce the throughput of large particles with a particle size of 100 ㎛ or more. The chemical composition of the particles showed a high Al content, and trace amounts of Mg, Si, and Zn were detected.

• 융합정보논문지
• /
• 제12권2호
• /
• pp.149-156
• /
• 2022

본 논문에서는 광센서의 주요 구성요소인 도체를 상압플라즈마 공정 기술을 이용하여 티타늄(Ti: Titanium) 박막을 형성하고자 하였다. 이를 위해 기존의 상압플라즈마 장비를 개조하였으며, CF4 가스를 이용하여 sputter용 4인치 크기의 Ti 타겟을 식각하여 그 부산물이 글라스 소재의 샘플에 코팅되는 방법을 이용하였다. 이러한 부산물이 약 2cm까지 형성되었으며, 색깔에 따라 총 15영역으로 구분할 수 있었다. SEM(Scanning Electron Microscopy) 및 EDS(Energy Dispersive Spectrometer), 4-point probe 장비를 이용하여 표면 형상 및 구성 원소를 분석하였으며, 또한, 전기적인 특성을 측정하였다. 증착률 및 Ti 비율을 고려한다면, 타겟에서 약 4.5mm에서 5mm 정도에 샘플을 위치시켜 코팅하면 전체적으로 균일한 박막이 형성되지만, 이 박막에 상당량의 플루오린이 함유되어 있어 박막의 전기적인 특성에 큰 영향을 미치는 것을 알 수 있었다. 따라서 플루오린을 제거하거나 증착시 최소화하는 방안에 대해 추가 실험 및 연구를 진행해야 할 것이다.

• 한국의류학회지
• /
• 제25권10호
• /
• pp.1770-1778
• /
• 2001

황토는 대표적인 천연 무기염재의 일종으로서 바람에 의해 운반되어 퇴적된 담황색 내지는 황회색을 띠는 실트질의 퇴적물을 일컫는다. 황토의 구성물질은 주로 석영, 장석, 산화철광물, 깁사이트 등의 여러 가지 점토광물을 포함하는데, 주로 적색을 띠는 것은 소량의 산화철 광물에 기인되는 경우가 많으며 황토를 구성하는 점토광물로는 버미큘라이트, 카오린 광물인 캐올리나이트와 할로이사이트, 일라이트 등이 있다. 본 연구에서는 면직물에 천연 무기염재인 황토를 사용한 염색시에 황토 단독염색과 콩즙 전처리 후 황토염색으로 나누어 염색을 실시하고, 원료 황토와 황토염색 후 면직물에 부착된 성분 간에 차이가 있는지를 확인하기 위해 X선 형광분석(X-ray fluorescence analysis, XRF)을 이용하여 염색 전.후 황토의 성분을 분석하였고, X선 회절분석(X-ray diffraction analysis, XRD)을 이용하여 황토 및 염색 전 후 면직물에 부착된 광물질의 주성분을 분석하였으며, energy dispersive spectrometer (EDS)가 장착된 주사전자현미경을 이용하여 면직물에 부착된 광물의 성분을 조사하였다. 그 결과, 황토로 면직물을 염색하는 경우 면직물에 부착되는 황토의 양과 K/S 값은 거 의 비례하여 증가하는 것으로 나타났다. 황토 염색 후 면직물에 부탁되는 주성분은 주로 SiO$_2$, A1$_2$O$_3$, Fe$_2$O$_3$등인 것으로 나타났으며, X선 회절분석과 EDS분석에 의해 캐올리나이트, 일라이트 등의 점토광물의 형태로 존재하는 것이 확인되었다.

• Journal of Electrical Engineering and Technology
• /
• 제1권2호
• /
• pp.246-250
• /
• 2006

Highly ordered gold nanodot arrays have been successfully obtained by vacuum evaporation using an anodic aluminum oxide (AAO) as a shadow mask. An AAO mask with the thickness of 300 um was prepared through an anodization process. The structure of the nanodot arrays was studied by a field- emission scanning electron microscope (FE-SEM) equipped with an energy dispersive spectrometer (EDS). A tapping mode atomic force microscope (AFM) was employed for studies of height and phase feature. The nanodot arrays were precisely reproduced corresponding to the hexagonal structure of the AAO mask in a large area. In the gold nanodot arrays, the average diameter of dots is approximately the same as the AAO pore size in the range from 70 um to 80 nm and 100 nm center-to-center spacing. EDS analysis indicated that the gold dots were almost entirely consisted of gold, a highly demanded material.

• 소성∙가공
• /
• 제15권8호
• /
• pp.539-543
• /
• 2006

Experimental studies are carried out in order to investigate the effects of heat treatment on the surface machined by W-EDM. In this work, two ways of heat treatment after W-EDM are considered. As a comparison, the machined surface by a traditional method such as milling/grinding is also considered. Thereby, specimens are prepared by four different machining methods. Those are (1) milling and then grinding, (2) wire-cut electric discharge machining (W-EDM), and (3) low temperature heat treatment or (4) high temperature heat treatment after W-EDM. The resulting surface roughness are measured and the changes of surface microstructures are investigated using the scanning electron microscope (SEM) with energy dispersive X-ray spectrometer (EDS). In general, heat treatment after W-EDM result in smoother surface and better chemical composition at the machined surface. Especially, high temperature tempering could remove defects in the thermally affected zone, which cause an overall deterioration of the surface machined by W-EDM.