• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.3
• /
• pp.543-548
• /
• 2010

There are produced the detent force caused by slot-teeth structures, end-effect and parallel magnetization of permanent magnet in permanent magnet linear synchronous motor. In this paper, we proposed to establish the auxiliary core for reducing detent force which is generated the discontinuity of magnetic circuits by end effect. The optimal design of the auxiliary core used a finite element analysis and design of experiment. To demonstrate the validity of the paper, the experiment results are compared with analysis ones.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.12
• /
• pp.71-77
• /
• 2010

A discontinuity of magnetic circuits according to the end effect is generated in PMLSM. And magnetic state of the 3 phase coils becomes unbalanced. Due to the unbalanced magnetic state, the unbalanced flux linkage, back electro-magnetic force and inductance of the 3 phase coils appear. In result, the circulating current is generated by unbalanced inductance even if the input voltages are in balanced state. Then the thrust and efficiency are decreased because of the circulating current. Therefore, in this paper, the unbalanced inductance and the thrust reduction according to discontinuity of magnetic circuits are analyzed by FEA(2D). To demonstrate the validity of the analysis results, the experiment results are compared with analysis results.

• Structural Engineering and Mechanics
• /
• v.26 no.5
• /
• pp.483-498
• /
• 2007

In case of considering the shear effect, the complete solutions are obtained for dynamic plastic response of a rigid, perfectly plastic hinged-free beam, of which one end is hinged and the other end free, subjected to a transverse strike by a travelling rigid mass at an arbitrary location along its span. Special attention is paid to new deformation mechanisms due to shear sliding on both sides of the rigid mass and the plastic energy dissipation. The dimensionless numerical results demonstrate that three parameters, i.e., mass ratio, impact position of mass, as well as the non-dimensional fully plastic shear force, have significant influence on the partitioning of dissipated energy and failure mode of the hingedfree beam. The shear effect can never be negligible when the mass ratio is comparatively small and the impact location of mass is close to the hinged end.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.151-154
• /
• 2004

To use the SLIM for servo system, the exact account of thrust about the initial speed is needed, but analyzing by equivalent circuit analyzing methode such as rotary induction motor, the error occurs because of the end effect. So, we applied the equivalent circuit considering the end effect of SLIM in this paper. The current control system is advanced the space vector pulse width modulation by using high arithmetic performance microprocessor such as DSP. In this paper, we use the dynamic characteristic analyzing methode that can calculate efficiently the end effect by using equivalent circuit methode in the operating SLIM system modeling and examine the output characteristics of SVPWM with PI controller.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.4
• /
• pp.395-403
• /
• 2002

The advanced space vector PWM is Implemented for the control system using high arithmetic performance microprocessor such as DSP. It is difficult to realize the complicate SLIM which is applied to SVPWM system, but widely used in vector control system or servo control system for AC motor because of its high performance in current control. In this paper, we use the dynamic characteristic analyzing method that can calculate efficiently the end effect by using equivalent circuit methode in the operating SLIM system modeling and examine the dynamic characteristics of SVPWM with PI controller.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.7
• /
• pp.1067-1074
• /
• 1994

This paper deals with the combined levitation and guidance EDS(Electrodynamic Suspension) Maglev system. Levitation and guidance forces generated in figured-of-eight coil are examined. End effect of Superconducting magnets is considered in that the air gap flux has been calculated using the finite number of magnets. Induced emfs and currents of ground coils are given as results. Eletromagnetic forces vary according to the built-in position of magnets. Levitation forces of the first magnet pair are the smellest and those of the second one are the largest. This result shows that the end effect of SCMs should be considered in a concentrated magnet system.

• Advances in materials Research
• /
• v.9 no.4
• /
• pp.265-287
• /
• 2020

A theoretical method to predict the interfacial stresses in the adhesive layer of reinforced concrete beams strengthened with porous FRP plate is presented in this paper. The effect due to porosity is incorporated utilizing a new modified rule of mixture covering the porosity phases. The adherend shear deformations have been included in the present theoretical analyses by assuming a linear shear stress through the thickness of the adherends. Remarkable effect of the porosity has been noted in the results. Indeed, the resulting interfacial stresses concentrations are considerably smaller than those obtained by other models which neglect the porosity effect. It was found that the interfacial stresses are highly concentrated at the end of the FRP plate, the minimization of the latter can be achieved by using porous FRP plate in particular at the end. It is also shown that the interfacial stresses of the RC beam increase with volume fraction of fibers, but decrease with the thickness of the adhesive layer.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.77-82
• /
• 2003

In end milling process, undeformed chip thickness and cutting force vary periodically with phase change of the tool. Recently, a model has been proposed to simulate the shear and friction characteristics of an up-end milling process in terms of the equivalent oblique cutting to this. In the current study, the varying undeformed chip thickness and the cutting forces in a down-end milling process have been replaced with the equivalent ones of oblique cutting. And, the down-end milling characteristics of SM45C has been compared with that of the up-end milling previously presented with different helix angles.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.6 s.67
• /
• pp.1-7
• /
• 2005

This paper deals with the design and aerodynamic analysis of a special-type impulse turbine, with an end plate for wave energy conversion. Numerical analysis was performed using a CFD code, FLUENT. The main idea of the proposed end plate was to minimize the adverse effect of tip clearance of turbine blade, and was borrowed from ducted propeller, with so-called penetrating end plate for special purpose marine vehicles. Results show that efficiency increases up to $5\%$, depending on the flow coefficient; a higher flow coefficient yields increased efficiency. Decrease of input coefficient CAwith an end plate is the main reason for higher efficiency. Performance of end plate at various design parameters, as well as flow conditions, was investigated; the advantages and disadvantages of the presentimpulse turbine were also discussed.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.872-873
• /
• 2007

This paper proposes a calculating method of resistance and inductance of end ring of squirrel cage induction motor for 2D finite element analysis. The squirrel cage of induction motor consists of bars and end rings. The resistance and inductance of end ring have an effect on the result of the finite element calaculation. If the end ring were excluded from the analysis, the good result could not be obtained. Therefore, we first simulate an axisymmetric magnetodynamic analysis for the end ring, and then calculate the interbar resistance and the end ring inductance. The calculated values are put into the external circuit of 2D finite element model of the induction motor. The proposed method is verified by comparing the numerical results with the experimental ones.