• Bulletin of the Korean Chemical Society
• /
• v.22 no.2
• /
• pp.219-227
• /
• 2001

The silver colloidal effects on the excited-state structure and intramolecular charge transfer (ICT) of p-N,N-dimethylaminobenzoic acid (DMABA) in aqueous cyclodextrin (CD) solutions have been investigated by UV-VIS absorption, steady-state and time-resolved fluorescence, and transient Raman spectroscopy. As the concentration of silver colloids increases, the ratio of the ICT emission to the normal emission (Ia /Ib) of DMABA in the aqueous $\alpha-CD$ solutions are greatly decreased while the Ia /Ib values in the aqueous B-CD solutions are significantly enhanced. It is also noteworthy that the ICT emission maxima are red-shifted by 15-40 nm upon addition of silver colloids, implying that DMABA encapsulated in $\alpha-CD$ or B-CD cavity is exposed to more polar environment. The transient resonance Raman spectra of DMABA in silver colloidal solutions demonstrate that DMABA in the excited-state is desorbed from silver colloidal surfaces as demonstrated by the disappearance of νs (CO2-)(1380 cm-1 ) with appearance of ν(C-OH)(1280 cm -1) band, respectively. Thus, in the aqueous B-CD solutions the carboxylic acid group of DMABA in the excited-state can be readily hydrogen-bonded with the secondary hydroxyl group of B-CD while in aqueous and $\alpha-CD$ solutions the carboxylic acid group of DMABA has the hydrogen-bonding interaction with water. Consequently, in the aqueous B-CD solutions the enhancement of the Ia /Ia value arises from the intermolecular hydrogen-bonding interaction between DMABA and the secondary hydroxyl group of B-CD as well as the lower polarity of the rim of the B-CD cavity compared to bulk water. This is also supported by the increase of the association constant for DMABA/ B-CD complex in the presence of silver colloids.

• Bulletin of the Korean Chemical Society
• /
• v.6 no.5
• /
• pp.287-291
• /
• 1985

The addition of poly(styrenesulfonate) (PSS) to $Ru(bpy)_3^{2+}$ solutions shifted the emission peak by 3 nm to red, and increased emission intensity by 1.8 times. By contrast, poly(vinylsulfonate) (PVS) had little effect on the fluorescence spectrum. The effects of PSS on the spectral properties of $Ru(bpy)_3^{2+}$, were attributed to the presence of a hydrophobic phenyl group in PSS, which interact with $Ru(bpy)_3^{2+}$ by, at least in part, hydrophobic effect. The binding constant of $Ru(bpy)_3^{2+}$ to PSS in 0.1 M NaCl was $6{\times}10^4\;M^{-1}$, and this value was about $10^3$ times higher than those of methyl viologen ($MV^{2+}$) and $Cu^{2+}$. The Stern-Volmer constants of emission quenching of $Ru(bpy)_3^{2+}$ by $MV^{2+}$ and $Cu^{2+}$ in 0.1 M NaCl solutions were 426 and 40 $M^{-1}$, which correspond to second order rate constants($k_q$) of $1.1{\times}10^9\;and\; 1.0{\times}10^8\;M^{-1}s^{-1}$, respectively. The presence of PSS enhanced $K_{SV's}\;by\;{\sim}50$ times, whereas PVS increased the values only 1-4 times. The large enhancing effect of PSS, despite of lower charge density than PVS, was explained in terms of longer life-time of photoexcited $Ru(bpy)_3^{2+}$ bound to PSS and strong association of $Ru(bpy)_3^{2+}$ to PSS due to a specific interaction involving hydrophobic effect. The variation of $K_{SV's}$ on the concentrations of PVS and PSS were also investigated for $Ru(bpy)_3^{2+}-MV^{2+}\;and \;Ru(bpy)_3^{2+}-Cu^{2+}$ photoredox systems.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.4
• /
• pp.46-57
• /
• 1996

The direct injection stratified charge(DISC) engine enhances the fuel tolerance and the antiknock tendency. This enhanc3d antiknock tendency allows use of a higher compression ratio which results in higher thermal efficiency. But its actual utilization is prevented by high emission combustion time and wall quenching will be the main causes of increasing unburned hydrocarbons in DISC system. In order to solve this problem, small aount of hydrogen was added to the charging air or injected fuel. The effects of hydrogen addition were examined experimentally by radial fuel injection using a pancake-type constant volume bomb. In case of the hydrogen addition to the charge of air, the combustion the amount of hydrogen. In case of the hydrogen addition to the fuel, the combustion pressure was significantly increased.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.1
• /
• pp.37-45
• /
• 2010

Computational simulation has been carried out to examine the effects of pilot injection to reduce both of NOx and Soot emissions in a marine diesel engine. For verification of the computational result, calculated cylinder pressure was matched to experimental pressure. In this study, the primary variables were injection timing, dwell time and injection rate while the amount of injection fuel was maintained constant. It was revealed that variation of pilot injection timing affects auto ignition and heat release rate. In the results, both of NO and soot emission were reduced without deterioration of in-cylinder pressure under the condition of $10^{\circ}$CA dwell time and 0.022kg/s injection rate.

• Clean Technology
• /
• v.28 no.2
• /
• pp.147-154
• /
• 2022

Titanate nanotubes (TNTs) were synthesized via alkaline hydrothermal treatment using commercial TiO₂ nanoparticles (P25). The TNTs were prepared at various TiO₂/NaOH ratios, hydrothermal temperatures, and hydrothermal times. The synthesized catalysts were characterized by X-ray diffraction, field-emission scanning electron microscopy, N₂ adsorption-desorption isotherms, field-emission transmission electron microscopy, and ultraviolet-visible spectroscopy. TNTs were generated upon a decrease in the TiO₂/NaOH ratio due to the dissolution of TiO₂ in the alkaline solution and the generation of new Ti-O-Ti bonds to form titanate nanoplates and nanotubes. The hydrothermal treatment temperature and time were important factors for promoting the nucleation and growth of TNTs. The TNT catalyst with the largest surface area (389.32 m² g^-1) was obtained with a TiO₂/NaOH ratio of 0.25, a hydrothermal treatment temperature of 130 ℃, and a hydrothermal treatment time of 36 h. Additionally, we investigated the photocatalytic activity of methyl violet 2B (MV) over the TNT catalysts under UV irradiation and found that the degradation efficiencies of the TNTs were higher than that of P25. Among the TNT catalysts, the TNT catalyst that was hydrothermally synthesized for 36 h (TNT 36 h) exhibited a 96.9% degradation efficiency and a degradation rate constant that was 4.8 times higher than P25 due to its large surface area, which allowed for more contact between the MV molecules and TNT surfaces and facilitated rapid electron transfer. Finally, these results were correlated with the specific surface area.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.5
• /
• pp.87-93
• /
• 2013

Recently, the amount of the mineral admixture including fly ash and ground granulated blast-furnace slag was increased for the purpose of $CO_2$ gas emission reduction in the concrete industry. However, in the case of korea, estimation model of strength development in concrete structural design code was prescribed a constant value according to cement type and curing method about the portland cement. therefore, the properties of strength development according to time of concrete using fly ash and ground granulated blast-furnace slag does not reflected estimation model of strength development. Accordingly, this paper was evaluated strength according to time on the concrete strength range using fly ash and ground granulated blast-furnace Slag and the strength development constant ${\beta}_{sc}$ of concrete according to the kind of the mineral admixture and mixing ratio was proposed.

• Membrane and Water Treatment
• /
• v.4 no.3
• /
• pp.175-189
• /
• 2013

A membrane bioreactor (MBR) with sludge retention time (SRT) of 300 days was maintained for over 2 years. Polypropylene microfiltration (MF) membrane with pore size of 0.2 ${\mu}m$ was used in the MBR system. The fouling behaviors of various sludge fractions from the MBR were studied and sub-divided resistances were analyzed. It was observed that $R_{cp}$ was a dominant resistance during the filtration of activated sludge, contributing 63.0% and 59.6% to the total resistance for MBR and sequential batch reactor (SBR) respectively. On the other hand, $R_c$ played the significant role during the filtration of supernatant and solutes, varying between 54.54% and 67.18%. Compared with $R_{cp}$ and $R_c$, $R_{if}$ was negligible, and $R_m$ values remained constant at $0.20{\times}10^{12}m^{-1}$. Furthermore, resistances of all sludge fractions increased linearly with rising mixed liquor suspended solids (MLSS) concentration and growing trans-membrane pressure (TMP), while the relationship was inversed between fraction resistances and cross flow velocity (CFV). Among all fractions of activated sludge, suspended solid was the main contributor to the total resistance. A compact cake layer was clearly observed according to the field emission scanning electro microscopy (FE-SEM) images.

• Journal of ILASS-Korea
• /
• v.7 no.1
• /
• pp.14-20
• /
• 2002

It is well known that the flow and spray characteristics is critical factor on the performance and emission of a direct injection diesel engine. So this study aims to investigate the interaction of flow and spray characteristics. At first, in cylinder flow distributions in swirl adaptor for 4-valve cylinder head of DI Diesel engine were investigated under steady conditions for different SCV angles mounted on the cylinder head with steady rig test and 2-D LDV. And the in-cylinder flow was quantified in terms of mean flow coefficient and swirl ratio/tumble ratio. It was found that the swirl ratio is controlled between 2.3 and 3.8. Then spray characteristics of the intermittent injection were investigated. PDA system was utilized for measurement of a droplet size and velocity. The analyses of the PDA results are carried out with Time Dividing Method. It was found that there is a correlation between the swirl flow and SMD. The droplet size and the velocity were nearly constant value with each SCV angle. And the swirl ratio is higher, SMD smaller. The swirl ratio was helpful factor to the atomization of droplet.

• Journal of Korean Ophthalmic Optics Society
• /
• v.5 no.2
• /
• pp.163-165
• /
• 2000

We investigated visible light radiated from Plasma Focus device by time-integrated analyzed method. Plasma focus is a device that translated from electric energy into visible light by electric discharge. Spectral analysis is using Monochromator(focal length = 0.5 m). Time-integrated spectrum is analyzed with densitometer the film which developed a constant range of wavelength. The condition of visible emission was that the discharging voltage was 13 kV and the working gas were Argon and Helium.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.2
• /
• pp.226-232
• /
• 2002

In tradition, there have been two kinds of drying methods, which are sun drying and artificial drying. The sun drying method which has been adopted traditionally has been replaced by the hot-air drying method which is one of the most general methods of artificial drying, with its simple drying system, low initial cost of drying plant, and easy operating method. But the hot-air drying method has some defects ; (1)much energy loss happens due to the discharge of hot air during the drying process, (2)control of drying rate is not easy on account of changing relative humidity of inlet air for uniform hot air temperature, (3)high temperature of floods in drying process brings about the production of low-grade drying products. Also, the hot-air drying method is inducing environmental and sanitary problems which are resulting from the emission of high temperature and high humidity air, including stick on the drying progress. Vacuum drying technique, whose drying time and 7uantity of exhausting energy is about 1/3 ~1/4 of hot air drying, is very excellent in the drying efficiency. As the results, it took about 20 hours for material to reach about 18% of the final moisture content in order to store products for a long time, from about 470% of the early moisture content at the beginning of drying, and maximum drying rate comes to about $0.35 kg/m^2hr$ at about 350% of the moisture content.