• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.243-244
• /
• 2022

In this paper, experiments were conducted on signal amplification of polymer capsules for application to Ground Penetrating Radar so as to enable real-time monitoring of polymer capsules inside concrete using the Morphology Dependent Resonance phenomenon. A TEM CELL and a vector network analyzer were used to analyze the difference in resonance frequency depending on the material of the sphere and the presence or absence of fracture. In order to manufacture a capsule of a size that can be measured using millimeter waves used in GPR, we manufactured a capsule with a 3D printer and analyzed the effects of the presence or absence of coating and the size of the capsule on the resonance frequency. Resonant frequency or signal amplification is more affected by diameter than coating. The capsule showing the highest amplification is the resin-coated 50 mm diameter capsule with a 316-fold increase and the lowest capsule is the uncoated 10 mm diameter capsule with a signal amplification of 11.9 times. These results demonstrate the potential of GPR to measure the position and state of self-healing capsules, which are small-sized polymers, in real time using millimeter waves.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.2
• /
• pp.213-218
• /
• 2022

In this paper, a technology for a high-efficiency wireless power transmission transmitting and receiving coil that can wirelessly charge a drone is introduced. The drone station implements the ability to charge the battery wirelessly without the need to remove the battery to charge the drone's battery. In order to charge the drone's battery in the shortest time, wireless charging efficiency must be high. In order to increase the wireless charging efficiency of the drone station, a method for manufacturing high-efficiency transmitting and receiving coils and a performance measurement method are presented. Transmitting and receiving coils were manufactured considering the size and weight of the drone so as not to interfere with the flight of the drone. Efficiency of 88% or more was realized at a distance of 40mm or more between the transmitting and receiving coils.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.232-232
• /
• 2021

수재해 저감과 예방을 위해서는 공간적 변동성을 반영한 정확한 면적 강우량의 측정은 필수적이다. 이러한 요구에 부응하기 위해 24 GHz 이중편파 전자파를 기반으로 소규모 공간 범위에 대해 저고도의 지상 강우를 30 m의 거리해상도로 관측할 수 있는 전파강수계가 개발되었다. 전파강수계는 시제품이 개발된 이래로 한국건설기술연구원 연천센터와 국내 여러 현장과 인도네시아 등에서 시험을 실시하였다. 임상훈 등(2020)은 전파강수계의 반사도와 비차등위상차를 이용한 강우 추정식을 개발하여 연천 및 거제 관측 자료에 적용한 바 있다. 본 논문에서는 연천센터에 분산 배치한 우량계 자료를 이용하여 전파강수계의 강우 공간분포 측정 성능을 평가하였다. 공간우량계는 15대 중 음영구역 바깥에서 정상 작동한 7개의 0.5mm급 우량계 자료와 핏게이지에 있는 0.2mm급 우량계 2대가 비교에 사용되었다. 전파강수계 강우강도는 비교 위치에 해당하는 점 주변의 레이 방향 5개(37.5 m에 해당) 및 방위각 방향 5개 게이트 등 총 25개의 복셀에서 산출된 강우 정보를 평균하여 비교하였다. 정확도는 지상우량계를 참값으로 보고 MAE(Mean absolute error)로 평가하였다. 그 결과 평균 4.2%의 오차를 보였으며, 우량계의 오차를 ±5%로 가정할 경우 3.3~7.9%로 나타났다. 전파강수계의 누적 강우량 값은 강우계에 비해 작은데, 이는 지속적인 관측을 통해 강우 산정의 정확도를 개선하는 것이 필요함을 의미한다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1D
• /
• pp.203-209
• /
• 2006

SAR (Synthetic Aperture Radar) technology, which is not influenced by cloud cover because of using electromagnetic wave of long wavelength, has an advantage in mapping the earth. NASA, recognizing these strong points of SAR, launched SRTM (Shuttle Radar Topography Mission), and acquired the topographic information of the earth. SRTM and NED (National Elevation Data) of USGS were used for the research and vegetation height map was produced through differentiating the two data. Correlation between SRTM-NED and planting year was analyzed to see the relationship. Strong correlation was detected and it shows the feasibility of estimating timber age and eventually creating timber age map from SRTM-NED. Additional analyses were conducted to check if the linearity is influenced by regional characteristics and forest uniformity. As results, the correlation between SRTM-NED and timber age is influenced by roughness of the terrain. Overall, this paper shows that timber age estimation using SRTM and NED can be sufficiently practical.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.253-253
• /
• 2022

수문조사 방법 및 기준은 각 국가별 기후, 유역 및 하천특성에 따라 다르게 제시되고 있으며, 세계기상기구(WMO)나 국제표준화기구(ISO)에서는 국제적으로 통용될 수 있는 기준을 제시하고 있다. 대부분의 국가에서는 국제기구 또는 수문조사 선진국(미국, 일본, 영국 등)에서 제시한 기준 및 방법을 도입하여 적용하고 있으며, 국내의 경우도 국제기준과 더불어 미국의 기준과 우리나라와 기후, 지형 및 하천특성이 비슷한 일본의 기준을 많은 부분에서 도입하였다. 유속계에 의한 유량측정 시 측선수를 늘리면 정확도를 높일 수 있지만 대하천 또는 수위(유속)가 급변하는 경우에는 측선수를 많이 해서 측정시간이 길어지면 오히려 정확도를 떨어뜨릴 수 있다. 특히, 국내에서 홍수시 신속한 측정에 사용되는 부자와 전자파표면유속계는 기존의 회전식유속계 측선수 기준을 적용하는 것은 적합하지 않다. 이에 따라, 우리나라 수문조사 전담기관인 한국수자원조사기술원에서는 전자파표면유속계 측선수 기준을 실무적으로 제시하고 있으나 이에 대한 기술적인 검토가 부족한 실정이다. 본 연구에서는 2016년~2020년까지 한국수자원조사기술원에서 측정된 58개 지점의 총 739개의 전자파표면유속계 측정성과에 대하여 수면폭 및 측선수 현황을 살펴보았다. 한국수자원조사기술원 일반기준 이상 측선수 비율은 646개(87.4%), 긴급기준 이상 측선수 비율은 739개(100.0%) 그리고 전체 평균값 이상 측선수 비율은 404개(54.7%)로 나타났다. 일반기준 이상 측선수가 많은 원인을 파악해보기 위하여 측선수를 최대구간유량비 20% 이상일 때까지 측선수를 10%씩 감소하여 산정된 유량의 변화를 검토하였다. 유량 변화 검토 결과 현장에서 유량측정 시 측선수의 등유량 배치, 최대구간유량비(20%) 및 불확도(±10%) 기준을 준수하기 위해서 기준 이상의 측선수를 확보하는 경향으로 판단되었다. 이러한 문제를 해소하기 위하여 측선수 감소에 따른 유량 편차율 ±10%와 불확도 ±10% 조건을 만족하는 수면폭 구간별 최소 기준을 제시하였으며, 이 기준을 적용할 경우 전자파표면유속계로 현장에서 보다 신속하고 정확한 유량측정을 수행할 수 있을 것으로 기대된다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.194-196
• /
• 2022

When electromagnetic wave transmitted from the radar antenna hits the target, a specific type of electric field is formed according to the electrical characteristics and appearance of the target, which is called an RCS pattern. There are various commercial programs that calculate the RCS of the target and plot the RCS pattern. For the analysis of large targets such as warships or ships, a program with a high frequency analysis method, which has a faster calculation speed than the low frequency analysis method is suitable. XGTD, a high-frequency analysis program, can quickly plot a two-dimensional RCS pattern for 360 degrees of a target, but a three-dimensional RCS pattern cannot be obtained. In this paper, it is proposed that a method of plotting two-dimensional RCS patterns of a target from various angles using XGTD, generating a three-dimensional RCS pattern using this, and converting it into a three-dimensional antenna pattern file.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.670-680
• /
• 2010

A low power single-chip CMOS receiver for 60 GHz mobile application are proposed in this paper. The single-chip receiver consists of a 4-stage current re-use LNA with under 4 dB NF, Cgs compensating resistive mixer with -9.4 dB conversion gain, Ka-band low phase noise VCO with -113 dBc/Hz phase noise at 1 MHz offset from 26.89 GHz, high-suppression frequency doubler with -0.45 dB conversion gain, and 2-stage current re-use drive amplifier. The size of the fabricated receiver using a standard 0.13 ${\mu}m$ CMOS technology is 2.67 mm$\times$0.75 mm including probing pads. An RF bandwidth is 6.2 GHz, from 55 to 61.2 GHz and an LO tuning range is 7.14 GHz, from 48.45 GHz to 55.59 GHz. The If bandwidth is 5.25 GHz(4.75~10 GHz) The conversion gain and input P1 dB are -9.5 dB and -12.5 dBm, respectively, at RF frequency of 59 GHz. The proposed single-chip receiver describes very good noise performances and linearity with very low DC power consumption of only 21.9 mW.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.9
• /
• pp.418-424
• /
• 2017

Magnesium has a higher specific strength than other metals and is widely used industry wide due to its excellent vibration absorption ability and electromagnetic wave shielding property.For example, it is used for automobile parts such as car seat frames and cylinder heads, and is widely used in electronic products such as notebook cases and mobile phone cases. In addition, it is in the spotlight as a bone-implant material used to assist in the treatment of damaged bones when the bones are cracked or broken. Currently, Ti alloy, stainless steel and Co-Cr-Mo alloy are used as the implant material, and the Mg alloy remains in research stage. The current problem with bone implant implants is that the patients must undergo reoperation to remove the implants after joint surgery. Magnesium, however, can achieve sufficient strength compared to current materials. In addition, since it is self-decomposed after the recovery, reoperation is not necessary. In this paper, Mg alloys were designed by adding harmless Ca and Zn to the human body. In order to improve the strength and corrosion resistance, the final alloy was designed by adding a small amount of Sr as a grain refiner. The radioactive elements of Sr are harmful to the human body, but other naturally occurring Sr elements are harmless. Microstructure analysis of the alloys was performed by optical microscopy and scanning electron microscopy. The mechanical properties and corrosion characteristics were evaluated by tensile test, potentiodynamic test and immersion test.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.4
• /
• pp.13-21
• /
• 2017

Ballasted track has been used as track system for more than 100 years. Ballasted track has advantages of low construction cost, flexible maintenance, low noise and vibration, and so on. However, ballasted track leads to continuous settlement which causes maintenance. Recently, increase in speed, traffic volume, and weight of train requires more frequent maintenance. Fouling, well-known phenomenon of accumulation of fine materials due to intrusion of subgrade and breakage of ballast materials, expedites the settlement (i.e., irregular settlement) of track. Ground Penetrating Radar (GPR) can be one of non-destructive tools that can evaluate fouling level of ballast. In this paper, a gain function based on the attenuation characteristics of ballast material is suggested in conjunction with Hilbert transform. Lab box tests and full-scale tests indicate that the suggested method reasonably classifies clean, fouled layers, and subgrade. However, additional study to eliminate effect of sleeper and to include the scattering features of the electromagnetic wave in ballast voids should be required in order to enhance the accuracy.

• Journal of the Korean earth science society
• /
• v.34 no.6
• /
• pp.575-587
• /
• 2013

DC electrical and electromagnetic survey was applied to evaluate the reserve of an iron mine site. We analyzed the borehole cores and the cores sampled from outcrops in order to decide which geophysical method was efficient for the evaluation of iron mine site and to understand the geological setting around the target area. Based on the core tests for specific weight, density, porosity, resistivity and P-wave velocity, showing that the magnetite could be distinguishable by the electrical property, we decided to conduct the electrical survey to investigate the irone mine site. According to previous studies, the DC electrical survey was known to have various arrays with high resolutions effective to the survey of the iron mine site. However it was also known that the skin depth is too shallow to grasp the deep structure of iron mine. To compensate the weakness of the DC electrical method, we applied the MagnetoTelluric (MT) survey. In addition, a Controlled Source MT (CSMT) method was also applied to make up the shortcoming of MT method which is weak for shallow targets. From the DC electrical and MT survey, we found a new low resistivity zone, which is believed to be a magnetite reserve beneath the old abandoned mine. Therefore, this study was confirmed for additional utility value.