• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.714-719
• /
• 1996

For the fabrication of the circuits, contact or terminal areas are usually coated with nickel and gold. Usually, diluted palladium solution is applied to initiate electroless nickel plating on the copper circuits. However, the trace amounts of palladium remains on the resin and it causes the extraneous deposition. We confirmed that selectivity was greatly improved by the treatment with the strong reducing agents such as SBH or DMAB. Bondability was greatly influenced by the contents of phosphorus in the deposited nickel. Stabilizers in the electroless gold plating were also influenced the bonding strength. The baths containing cupferron or potassium nickel cyanide as a stabilizer showed superior bondability. The gold deposits having strong orientation with Au(220) and Au(311) showed good bond ability.

• Journal of Powder Materials
• /
• v.11 no.3
• /
• pp.224-232
• /
• 2004

Ni-diamond composite powders with nickel layer of round-top type on the surface of synthetic diamond (140/170 mesh) were prepared by the electroless plating method (EN) with semi-batch reactor. The effects of nickel concentration, feeding rates of reductant, temperature, reaction time and stirring speeds on the weight percentage and morphology of deposited Ni, mean particle size and specific surface area of the composite powders were investigated by Atomic Adsortion Spectrometer, SEM-EDX, PSA and BET. It was found that nucleated Ni-P islands, acted as catalytic sites for further deposition and grown into these relatively thick layers with nodule-type on the surface of diamond by a lateral growth mechanism. The weight percentage of Ni in the composite powder increased with reaction time, feeding rate of reductant and temperature, but decreased with stirring speed. The weight percentage of Ni in Ni-diamond composite powder was 55% at 150 min., 200 rpm and 7$0^{\circ}C$ .

• Journal of the Optical Society of Korea
• /
• v.19 no.3
• /
• pp.217-221
• /
• 2015

Developing a metallization that has low cost and high efficiency is essential in solar-cell industries, to replace expensive silver-based metallization. Ni/Cu two-step metallization is one way to reduce the cost of solar cells, because the price of copper is about 100 times less than that of silver. Alkaline electroless plating was used for depositing nickel seed layers on the front electrode area. Prior to the nickel deposition process, 2% HF solution was used to remove native oxide, which disturbs uniform nickel plating. In the subsequent step, a nickel sintering process was carried out in $N_2$ gas atmosphere; however, copper was plated by light-induced plating (LIP). Plated nickel has different properties under different bath conditions because nickel electroless plating is a completely chemical process. In this paper, plating bath conditions such as pH and temperature were varied, and the metal layer's structure was analyzed to investigate the adhesion of Ni/Cu metallization. Average adhesion values in the range of 0.2-0.49 N/mm were achieved for samples with no nickel sintering process.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.909-911
• /
• 1999

Metalization technology of the fine patterns by electroless plating is required in place of electrodeposition as high-density printed circuit boards (PCB) become indispensable with the miniaturization of electronic components. Electroless nickel plating is a suitable diffusion barrier between conductor metals, such as Al and Cu, and solder is essetional in electronic packaging in order to sustain a long period of service. Moreover, Electroless nickel has particular characteristics including non-magnetic property, amorphous structure, wear resistance, corrosion protection and thermal stability. In this study fundamental aspects of electroless nickel deposition were studied with effect of complexeing agents of different kinds. Then, the property of electroless deposit are controlled by the composition of the deposition solution, the deposition condition such as temperature and pH value and so on. the characteristics of the deposits has been carried out.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.3
• /
• pp.131-137
• /
• 2007

The typical MCFC (molten carbonate fuel cell) anode is made of Ni-10%Cr alloy. The work of this paper is focused concerning long life of anode because Ni-10% Cr anode is suffering from sintering and creep behavior during cell operation. Therefore, Ni-coated Alumina powder($20{\mu}m$) was developed by electroless nickel plating. Optimum condition of electroless nickel coation on $20{\mu}m$ alumina is as follows: pH 11.7, temperature $65{\sim}80^{\circ}C$, powder amount $100cm^2/l$. The deposition rate for Ni-electroless plating was as a function of temperature and activation energy was evaluated by Arrhenius Equation thereby activation energy calculated slope of experimental data as 117.6 kJ/mol, frequency factor(A) was $6.28{\times}10^{18}hr^{-1}$, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.3
• /
• pp.29-34
• /
• 2020

The behavior of brittle fracture of electroless nickel immersion gold (ENIG) /Sn-3.0wt.%Ag-0.5wt.%Cu (SAC305) solder joints was evaluated. The pH of the electroless nickel plating solution for ENIG surface treatment was changed from 4.0 to 5.5. As the pH of the Ni plating solution increased, pin hole in the Ni-P layer increased. The thickness of the interfacial intermetallic compound (IMC) of the solder joint increased with pH of Ni plating solution. The high speed shear strength of the SAC305 solder joint on ENIG surface finish decreased with the pH of the Ni plating solution. In addition, the brittle fracture rate of the solder joint was the highest when the pH of the Ni plating solution was 5.

• Journal of the Korean institute of surface engineering
• /
• v.22 no.1
• /
• pp.43-51
• /
• 1989

The characteristion of composite electroless Nikel palting on the condition of adding 3kinds ceramic dispersives, Al2O3, Si3O4 and artificial diamond powder were studied. Decreasing solution temperature for composite plating was required to depress the spontaneous decomposition caused by dispersive including enlargement of reaction surface. The rate of composite plating was faster than that of general electroless-Nickel plating without dispersive. this increasing tendency of plating rate was remarkable for the active catalysis, like diamond powder.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.3
• /
• pp.21-27
• /
• 2007

Nickel bumps for ACF(anisotropic conductive film) flip chip application were fabricated by electroless and electro plating and their mechanical properties and impact reliability were examined through the compressive test, bump shear test and drop test. Stress-displacement curves were obtained from the load-displacement data in the compressive test using nano-indenter. Electroplated nickel bumps showed much lower elastic stress limits (70MPa) and elastic moduli ($7.8{\times}10^{-4}MPa/nm$) than electroless plated nickel bumps ($600-800MPa,\;9.7{\times}10^{-3}MPa/nm$). In the bump shear test, the electroless plated nickel bumps were deformed little by the test blade and bounded off from the pad at a low shear load, whereas the electroplated nickel bumps allowed large amount of plastic deformation and higher shear load. Both electroless and electro plated nickel bumps bonded by ACF flip chip method showed high impact reliability in the drop impact test.

• Polymer(Korea)
• /
• v.34 no.1
• /
• pp.25-31
• /
• 2010

Polymer core and metal shell composite particles have been prepared by the electroless nickel plating on the surface of monodisperse polystyrene microspheres. Various sizes of polystyrene particles with highly monodisperse state could be synthesized by controlling the dispersion medium in dispersion polymerization. Electroless nickel plating was performed on the polystyrene particle with diameter of $3.4\;{\mu}m$. The morphology of polystyrene/nickel composite particles was investigated to see the effect of the plating conditions, such as the $PdCl_2$ and glycine concentrations and the dropping rate of nickel plating solution, on nickel deposition. With $PdCl_2$ and glycine concentrations at more than 0.4 g/L and 1 M, respectively, more uniform nickel layer and less precipitated nickel aggregates were formed. At the given plating time of 2 h, the same amount of plating solution was introduced by varying the dropping rate. Though the effect of dropping rate on particle morphology was not noticeable, the dropping rate of 0.15 mL/min for 60 min showed rather uniform plating.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.3
• /
• pp.263-271
• /
• 2003

Optimal conditions of electroless nickel plating in acid baths has been studied for industrial applications of a developed EN solution. The phosphorus content in the deposition ranges from 8 to $12\;wt.\%$. The investigated EN plating parameters are ion concentrations of nickel and hypophosphite, concentration of reducing and complexing agent, temperature, and pH. The average plating rate of Ni-P deposition was ca. $14{\mu}m/h$. The EN solution used shows a deposition rate of $10{\mu}m/h$ up to seven metal turnovers.