• Korean Journal of Materials Research
• /
• v.13 no.10
• /
• pp.640-644
• /
• 2003

NiCr thin films were fabricated by rf magnetron sputtering for applying to both the top electrode and absorption layer on Pb(Zr, Ti)O$_3$(PZT) thin films for infrared sensors. The rms roughness and resistivity of NiCr films prepared with Ni power of 80 W and Cr power of 50 W showed the most stable oxidation resistance after annealing at $600^{\circ}C$ for 5 min in oxygen ambient. The rms roughness and resistivity of NiCr films annealed at $V^{\circ}C$ in oxygen ambient were about 2$0\AA$ and $70 \mu$Ω-cm, respectively. As-deposited Ni/PZT/Pt and NiCr (Ni 80 W, Cr 50 W)/PZT/Pt structures showed well saturated hysteresis loops. However, in case of the samples annealed at $500^{\circ}C$ in oxygen ambient, only NiCr/PZT/Pt showed saturated loops having a remanent polarization of 20$\mu$C/$\textrm{cm}^2$. Ultra-thin NiCr films showed a possibility as a top electrode for infrared sensors.

• Journal of Korean Vacuum Science & Technology
• /
• v.5 no.2
• /
• pp.47-51
• /
• 2001

To obtain high remnant polarization and good crystalinity of ferroelectric thin films in non-volatile memory devices, the high temperature treatment in oxygen ambient is inevitable. Severe problems that occur in this process are oxygen diffusion into substrate, oxidation of electrode and buffer layer, degradation of microstructure and so on. We made ruthenium dioxide thin film by reactive sputtering with oxygen and argon mixture atmosphere. Comparing quantitatively the core-level spectra of Ru and RuO$_2$ obtained by x-ray photoelectron spectroscopy(XPS), we found that chemical state of RuO$_2$ is very stable and of good resistance to oxygen diffusion and oxidation of adjacent layers. It opens the use of RuO$_2$ thin film as a multifunctional layer of good conducting electrode and resistive barrier for the diffusion and the oxidation. We also suggest a correct understanding of Ru 3d core-level spectrum for RuO$_2$ based on the scheme of final state screening and charge transfer satellites.

• Analytical Science and Technology
• /
• v.8 no.4
• /
• pp.723-730
• /
• 1995

Cyclic voltammetry and in situ STM were employed to examine the interfacial structures of a Pt(111) electrode in 0.1 mM KCN (pH9.5) and 0.1 mM KSCN (pH7) solutions. In situ STM atomic resolution revealed well ordered (2${\surd}$3${\times}$2${\surd}$3)$R30^{\circ}$-6CN and ($2{\times}2$)-2SCN structures within the double layer charging region. Six CN adsorbates formed a hollow hexagon, which embraced a coadsorbed $K^+$ cation. In contrast, the coadsorbed $K^+$ cations on the SCN covered Pt(111) were poorly ordered, despite adsorbed SCN formed a long range ordered ($2{\times}2$)-2SCN adlattice. In situ STM revealed the pronounced influence of potential in controlling the structures of compact layers at the proximity of a Pt electrode. Cathodic polarization facilitated the replacement of the coadsorbed cations by protons.

• Korean Journal of Crystallography
• /
• v.11 no.2
• /
• pp.95-101
• /
• 2000

Ferroelectric SrBi2Ta2O9 (SBT) thin films of Pt/Ti/SiO2 electrode were fabricated using a sintered SBT target with various Bi2O3 content by rf magnetron sputtering. Good hysteresis loop characteristics were observed in the SBT thin films deposited with 50mol% excess Bi target. SBT thin films crystallized from 650℃ however, good hysteresis loop can be obtained in the film annealed above 700℃. pt/TiO2/SiO2 and Pt/SiO2 electrodes were also used to investigate the Pt electrode dependence of SBT thin films. SBT thin films showed random oriented polycrystalline structure and similar morphology regardless of electrodes with quite different surface morphology. A 0.2㎛ thick SBT film annealed at 750℃ exhibited the remanent polarization (2Pr) of μC/㎠ and coercive voltage(Vc) of 1V at an applied voltage of 5V.

• Korean Membrane Journal
• /
• v.10 no.1
• /
• pp.46-52
• /
• 2008

Optimization of ionomer solution was conducted in order to improve the performance of MEAs in PEMPC. The interface between membrane and electrodes in MEAs is crucial region determining fuel cell performance as well as ORR reaction at cathode. Through the modification of Nafion ionomer content at the interface between membrane and electrodes, an optimal content was obtained with Nafion 115 membranes. Two times higher current density was obtained with the outer Nafion sprayed MEA compared with the non-sprayed one. In addition, the symmetrical impedance spectroscopy mode (SM) exhibited that the resistances of membrane area, proton hydration, and charge transfer decreased as the outer Nafion is sprayed. From the polarization curves and SM, the highest current density and the lowest resistance was obtained at the outer ionomer content of $0.15\;mg\;cm^{-2}$.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.2
• /
• pp.132-137
• /
• 2010

This study is concerned the electrocatalytic generation of oxygen gas at electrochemically deposited manganese oxide electrode in KOH solution. Manganese oxide nanoparticles electrodeposited onto relatively substrate, e.g glassy carbon, Au, Ti electrode. MnOx is electrodeposited in nanorod structure which cover the overall surface of the substrate. The $\gamma$-MnOOH that is kind of manganese oxide species plays a significant role as a catalytic mediator, which promote 4-electron reduction process. Modified electrodes with electrodeposited manganese oxide structures resulted in significant decrease in the anodic polarization compared with the unmodified electrodes in alkaline media.

• Corrosion Science and Technology
• /
• v.10 no.2
• /
• pp.71-75
• /
• 2011

Corrosion properties of Al-0.3Ga-0.3Sn, Al-0.3Mn-0.3Ga, and Al-0.3Mn-0.3Sn alloys were examined to develop an anode material for Al-air battery with alkaline aqueous or ethanol electrolyte. The results of potentiodynamic polarization tests showed that the electrode potential of the Al alloys were lower than the pure Al, implying the cell voltage can be increased by using one of these alloys for an anode in 4 M KOH aqueous solution. The corrosion rate appeared to be increased by alloying Ga but to be reduced by Sn and Mn in the aqueous solution. The ethanol solution is expected to improve the cell performance in that the electrode potential and the corrosion rate of Al were lower in ethanol solution than in aqueous solution. However the Al-(Ga, Sn, Mn) alloys are not favorable in ethanol solution because of the high potential and corrosion rate.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2022-2024
• /
• 2005

Electrical double-layer capacitor (EDLC) is an electrochemical energy storage device in which electric charges only accumulated by a pure electrostatic attraction force are stored on the electrolyte-electrode interface in a form of double layer and separated by the electrolyte. The composite was prepared by mixing nanosize $TiO_2$ and activated carbon through a means of ultrasonic vibration in ethanol solution for 30 min in various mass ratios of $AC:TiO_2$ to form activated carbone-semiconducting oxide composites. Either 1.0 M $LiClO_4/EC-DEC$ or $Et_4NBF_4$/EC-DEC was used as the electrolyte. It was found that with modification of $TiO_2$, the specific capacitance of activated carbon measured at $1mA/cm^2$ was increased from 40 to 50 F/g. This method is unique in comparison the conventional method because it uses semiconducting TiO2 other than electrochemically active materials such as $RuO_2$. The increase in specific capacitance could be attributed to the decrease in electric polarization, caused by the introduction of $RuO_2$.

• Geophysics and Geophysical Exploration
• /
• v.17 no.4
• /
• pp.247-252
• /
• 2014

Gagok Mine, which is skarn deposits, includes sulfide minerals such as sphalerite, galena, chalcopyrite, and pyrrhotite. To explore these minerals, spectral induced polarization (SIP) is relatively effective compared to other geophysical exploration methods because there is a strong IP effect caused by electrode polarization. In the SIP, the chargeability related to sulfide mineral contents and the time constant related to the grain size of the minerals are obtained. For this reason, we aim to compare difference in the mineralized characteristics between two orebodies in the Gagok Mine by using the chargeability and the time constant. For this study, we sampled ores from the south of Wolgok orebody and the north of Sungok orebody. In order to recognize the mineralization characteristics, the metal content of the samples was measured by a potable XRF and the SIP data of the samples were acquired by using a laboratory SIP measurement system. As a result, the metals in the samples such as Pb, Zn, Cu, and Fe were detected by the portable XRF measurement. In particular, the Fe and Zn contents were far higher than the other metals. The Fe and the Zn were caused by the sphalerite and the pyrrhotite through microscopy. The Wolgok orebody had higher sulfide mineral contents than the Sungok orebody and the result corresponded with the chargeability result. However, we considered that the Sungok orebody had a larger sulfide mineral grain size than the Wolgok orebody because the time constant of the Sungok orebody was larger.

• Applied Chemistry for Engineering
• /
• v.3 no.3
• /
• pp.527-534
• /
• 1992

Raney nickel was used as catalyst in the hydrogen electrode for an alkaline fuel cell. The hydrogen electrode manufactured with the Raney nickel catalyst which was sintered at $700^{\circ}C$ was found to have the highest electrode performance. Using the Raney nickel powder of average particle size $90{\AA}$ for the electrode, the current density which had been measured was $450mA/cm^2$ at $80^{\circ}C$ using 6N KOH solution as an electrolyte. The effects of PTFE addition were investigated with CO-chemisorption, polarization curves and Tafel slope. CO-chemisorption had shown the optimum value when the Raney nickel was mixed with 5wt% of PTFE, but from the current density and Tafel slope at porous Raney nickel electrode, the appropriate value of PTFE addition was 10wt%. Recommendable Ni and Al portion for Raney nickel was 60 : 40 and loading amount was $0.25g/cm^2$. Also the influence of pressing pressure for manufacturing catalytic layer and for junction with gas diffusion layer was examined. The morphology of catalyst surface was investigated with SEM. The influence of reactivation time and heat-treatment temperature were also studied.