• Journal of Electrochemical Science and Technology
• /
• v.4 no.3
• /
• pp.102-107
• /
• 2013

The electrochemical properties of Mg-doped $LiFe_{0.48}Mn_{0.48}Mg_{0.04}PO_4$ and pure $LiFe_{0.5}Mn_{0.5}PO_4$ olivine cathodes are examined and the lattice parameters are refined by Rietveld analysis. The calculated atomic parameters from the refinement show that $Mg^{2+}$ doping has a significant effect in the olivine $LiFeMnPO_4$ structure. The unit cell volume is 297.053(2) ${\AA}^3$ for pure $LiFe_{0.5}Mn_{0.5}PO_4$ and is decreased to 296.177(1) ${\AA}^3$ for Mg-doped $LiFe_{0.48}Mn_{0.48}Mg_{0.04}PO_4$ sample. The doping of $Mg^{2+}$ cation with atomic radius smaller than $Mn^{2+}$ and $Fe^{2+}$ ion induces longer Li-O bond length in $LiO_6$ octahedra of the olivine structure. The larger interstitial sites in $LiO_6$ octahedra facilitate the lithium ion migration and also enhance the diffusion kinetics of olivine cathode material. The $LiFe_{0.48}Mn_{0.48}Mg_{0.04}PO_4$ sample with larger Li-O bond length delivers higher discharge capacities and also notably increases the rate capability of the electrode.

• Macromolecular Research
• /
• v.8 no.6
• /
• pp.276-284
• /
• 2000

A wettability chemogradient on poly(L-lactide-co-glycolide) (PLGA) films was prepared by treating the films in air with corona from a knife-type electrode whose power increases gradually along the sample length. The PLGA surfaces oxidized gradually with the increasing corona power, and the wettability chemogradient was created on the surfaces as evidenced by the measurement of water contact angles and electron spectroscopy for chemical analysis. The wettability chemogradient PLGA surfaces were used to investigate the interaction of four different types of cells such as hepatoma (Hep G2), osteoblast (MG 63), bovine aortic endothelial (CPAE), and fibroblast (NIH/3T3) cells in terms of the surface hydrophilicity/hydrophobicity of PLGA. The cells adhered and grown on the chemogradient surface along the sample length were counted and observed by scanning electron microscopy. It was observed that the cells were adhered, spread, and grown more onto the positions with moderate hydrophilicity of the wettability chemogradient PLGA surface than the more hydrophobic or hydrophillic positions, regardless of the cell types used. The maximum adhesion and growth of the cells appeared at around water contact angles of 53～55°. This result seems closely related with the serum protein adsorption on the surface; the serum proteins were also adsorbed more onto the positions with moderate hydrophilicity of the wettability chemogradient surface. It seems that the wettability plays important roles for cell adhesion, spreading and growth on the PLGA surface. The surface modification technique used in this study may be applicable tothe area of tissue engineering for the improvement of tissue compatibility of films- or scaffold-type substrates.

• Journal of Advanced Navigation Technology
• /
• v.25 no.1
• /
• pp.90-95
• /
• 2021

In this paper, the design method for a high-sensitivity compact resonator for chipless RFID tags is proposed. Proposed high-sensitivity compact resonator uses an interdigital-capacitor structure instead of a capacitor-shaped strip structure in a conventional ELC resonator. The length of the electrode plate of the IDC structure is longer than that of the conventional capacitor-shaped structure, resulting in a larger equivalent capacitance of the resonator. This can lower the resonant peak frequency of the RCS characteristic. Two resonators with the same length of the square loop and the width of the strip are fabricated on an RF-301 substrate with a thickness of 0.8 mm. The experiment results show that the resonant peak frequency and value of the bistatic RCS for the ELC resonator were 4.305 GHz and -30.39 dBsm, whereas those of the proposed IDC resonator were 3.295 GHz and -36.91 dBsm. Therefore, the size of the resonator is reduced by 23.5% based on the measured resonant peak frequency of the RCS characteristic.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.2
• /
• pp.60-64
• /
• 2023

In this study, the electrical contact resistance characteristics between graphene and metals, which is one of important factors for the performance of graphene-based devices, were compared. High-quality graphene was synthesized by chemical vapor deposition (CVD) method, and Al, Cu, Ni, and Ti as electrode materials were deposited on the graphene surface with equal thickness of 50 nm. The contact resistances of graphene transferred to SiO₂/Si substrates and metals were measured by the transfer length method (TLM), and the average contact resistances of Al, Cu, Ni, and Ti were found to be 345 Ω, 553 Ω, 110 Ω, and 174 Ω, respectively. It was found that Ni and Ti, which form chemical bonds with graphene, have relatively lower contact resistances compared to Al and Cu, which have physical adsorption properties. The results of this study on the electrical properties between graphene and metals are expected to contribute to the realization of high-performance graphene-based devices including electronics, optoelectronic devices, and sensors by forming low contact resistance with electrodes.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.5
• /
• pp.207-214
• /
• 2004

This paper presents the characteristics of transient and effective impulse impedances for deeply driven grounding electrodes used in soil with high resistivity or in downtown areas. The laboratory test associated with the time domain performance of grounding piles subjected to a lightning stroke current has been carried out using an actual-sized model grounding system. The ground impedances of the deeply driven ground rods and grounding pile under impulse currents showed inductive characteristics, and the effective impulse ground impedance owing to the inductive component is higher than the power frequency ground impedance. Both power frequency ground impedance and effective impulse ground impedance decrease upon increasing the length of the model grounding electrodes. Furthermore, the effective impulse ground impedances of the deeply driven grounding electrodes are significantly amplified in impulse currents with a rapid rise time. The reduction of the power frequency ground impedance is decisive to improve the impulse impedance characteristics of grounding systems.

• Macromolecular Research
• /
• v.8 no.1
• /
• pp.6-11
• /
• 2000

In this study, we examined the charging behavior of chopped carbon fibers during electro-flocking process, which is one of the key processes of the novel technique for fabricating conductive polymer composite films. Short carbon fibers (CF) during electroflocking were electrically charged by the combined effect of contact charging, corona charging and tribocharging. The specific charge built on CF surface was measured by using Faraday cup method. Specific charge increased not only with increasing electric field strength and potential impressed to mesh electrode as expected from theoretical considerations in literature, but with decreasing mesh opening size due to the improved contact charging condition. However, CF length was found unexpectedly to influence the amount of CF specific charge due to the agglomerated nature of CF flocks leading to the change in charging conditions.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1808-1810
• /
• 2004

This paper describes the discharge characteristics of liquid $SF_6$ (-41$[^{\circ}]$, 1.7[atm]) and $LN_2$ for plane to plane, needle to plane, plane to needle and sphere to plane electrode with gap variations from 1[mm] to 12[mm]. From this result, the breakdown voltage was increased with increasing gap length. Especially, the formation of bubbles by evaporation was observed in spite of non-applying voltage source. A corona is created of the applying voltage from the bubbles on the electrodes applied voltage. We consider it equal mechanism of corona as void exists in solid insulator. The results of liquid $SF_6$ and $LN_2$ discharge characteristics were caused by bubble formed evaporation and applied electric field voltage. Corona was happened to weak bubble and was proceed to new bubble breakdown.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.3
• /
• pp.901-905
• /
• 2012

In this study, we investigated the pure geometrical effect of porous materials in gas adsorption using the grand canonical Monte Carlo simulations of primitive gas-pore models with various pore geometries such as planar, cylindrical, and random pore geometries. Although the model does not possess atomistic level details of porous materials, our simulation results provided many insightful information in the effect of pore geometry on the adsorption behavior of gas molecules. First, the surface curvature of porous materials plays a significant role in the amount of adsorbed gas molecules: the concave surface such as in cylindrical pores induces more attraction between gas molecules and pore, which results in the enhanced gas adsorption. On the contrary, the convex surface of random pores gives the opposite effect. Second, this geometrical effect shows a nonmonotonic dependence on the gas-pore interaction strength and length. Third, as the external gas pressure is increased, the change in the gas adsorption due to pore geometry is reduced. Finally, the pore geometry also affects the collision dynamics of gas molecules. Since our model is based on primitive description of fluid molecules, our conclusion can be applied to any fluidic systems including reactant-electrode systems.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.11
• /
• pp.91-99
• /
• 1998

A 5Gbps LiNbO$_3$ optical phase modulator was designed, packaged and it's properties were characterized for optical communications. The APE(annealed proton exchange) method was employed for the optical waveguide and the electrode of ACPS (asymmetric coplanar strip) type was formed by electro-plating on LiNbO$_3$ for applying microwave signal with a dimension of width 18${\mu}{\textrm}{m}$, gap 9${\mu}{\textrm}{m}$ and length 50mm. The fabricated single-moded modulator operated at a 1550nm wavelength exhibits its modulation bandwidth, insertion loss and driving voltage of 7㎓, 3.0dB and 6V, respectively.

• Journal of Welding and Joining
• /
• v.35 no.1
• /
• pp.43-48
• /
• 2017

Pulse TIG (Tungsten Inert Gas) welding is often considered the most difficult of all the welding processes commonly used in industry. Because the welder must maintain a short arc length, great care and skill are required to prevent contact between the electrode and the workpiece. Pulse TIG welding is most commonly used to weld thin sections of stainless steel, non-ferrous metals such as aluminum, magnesium and copper alloys. It is significantly slower than most other welding techniques and comparatively more complex and difficult to master as it requires greater welder dexterity than MIG or stick welding. The problems associated with manual TIG welding includes undercutting, tungsten inclusions, porosity, Heat affected zone cracks and also the adverse effect on health of welding gun operator due to amount of tungsten fumes produced during the welding process. This brings the necessity of automation. Hence, In this paper an attempt has been made to build a customerized setup of Pulse TIG welding based on through review of Pulse TIG welding parameters. The cost associated for making automated TIG is found to be low as compared to SPM (Special Purpose machines) available in the market.