• ETRI Journal
• /
• 제33권3호
• /
• pp.462-465
• /
• 2011

A millimeter-wave (mm-wave) high-linear low-noise amplifier (LNA) is presented using a 0.18 ${\mu}m$ standard CMOS process. To improve the linearity of mm-wave LNAs, we adopted the multiple-gate transistor (MGTR) topology used in the low frequency range. By using an MGTR having a different gate-source bias at the last stage of LNAs, third-order input intercept point (IIP3) and 1-dB gain compression point ($P_{1dB}$) increase by 4.85 dBm and 4 dBm, respectively, without noise figure (NF) degradation. At 33 GHz, the proposed LNAs represent 9.5 dB gain, 7.13 dB NF, and 6.25 dBm IIP3.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2002년도 동계연구발표회 논문개요집
• /
• pp.200-201
• /
• 2002

Recently, a countermeasure for the electromagnetic noise emission on RF integrated transmission line using the loss generation of ferromagnetic thin films is briefly suggested$\^$1,2/. Without the magnetic film, the noise harmonics of the signal pass through the transmission line with only a little attenuation. The ideal role of magnetic film is not to raise insertion losses in the pass-band and to give as large attenuation as possible to eliminate the noise harmonics at the stop-band, the frequency range higher than the meaningful signal as shown in Fig. 1. and Fig. 2. (omitted)

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1601-1602
• /
• 2006

A cascode low noise amplifier(LNA) for a 2.45GHz RFID reader is designed using 0.25um CMOS technology. There are four LNA design techniques applied to the cascode topology. In this paper, power-constrained simultaneous noise and input matching(PCSNIM) technique is used for low power consumption and achieving the noise matching and input matching simultaneously. Simulation results demonstrate a noise figure of 2.75dB, a power gain of 10.17dB, and a dissipation power of 8.65mW with 1V supply.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2333-2335
• /
• 2005

Various CMOS quadrature-voltage-controlled oscillators(QVCOs) are designed and fabricated for the comparison of the phase noise. The core VCO is composed of two Colpitts oscillators which are cross-coupled with PMOS pair. For the comparison of phase noise with the proposed scheme, the conventional LC VCO followed by the frequency-divide-by-two is designed. The simulation result demonstrate that the proposed scheme shows better phase noise performance by 6dB than that of a conventional scheme in which LC VCO is followed by the frequency-divide-by-two.

• Journal of Electrical Engineering and Technology
• /
• 제7권2호
• /
• pp.255-263
• /
• 2012

This paper presents the smart interacting multiple model (SIMM) using the concept of predicted point and maximum noise level. Maximum noise level means the largest value of the mere noises. We utilize the positional difference between measured point and predicted point as acceleration. Comparing this acceleration with the maximum noise level, we extract the acceleration to recognize the characteristics of the target. To estimate the acceleration, we propose an optional algorithm utilizing the proposed method and the Kalman filter (KF) selectively. Also, for increasing the effect of estimation, the weight given at each sub-filter of the interacting multiple model (IMM) structure is varying according to the rate of noise scale. All the procedures of the proposed algorithm can be implemented by an on-line system. Finally, an example is provided to show the effectiveness of the proposed algorithm.

• 한국소음진동공학회논문집
• /
• 제19권1호
• /
• pp.3-9
• /
• 2009

This paper presents the reduction of acoustic noise generated by electromagnetic force in an induction motor of the electrical forklift. After summarizing the electromagnetic excitation forces due to the interaction between the stator/rotor slot permeance and the stator winding magnetomotive force, the effects of the electromagnetic force on the noise and vibration of an induction motor are analyzed. In order to experimentally identify the noise sources of the motor, the signal analyses for noise and vibration are performed by using waterfall plots of noise and vibration spectrums. It is found that severe noise and vibration are caused by the electromagnetic force when the mode number of the excitation shape for a stator is low. Furthermore, it is verified that the motor noise is amplified if the excitation frequency of the electromagnetic force coincides with one of the natural frequencies of the stator. It is experimentally demonstrated that this severe noise can be considerably reduced by structure modifications. Finally, some design guidelines are suggested to develop an induction motor with a low level of noise.

• 한국소음진동공학회논문집
• /
• 제13권4호
• /
• pp.300-307
• /
• 2003

This paper presents the multi-mode noise reduction of smart panels of which passive piezoelectric shunt damping is introduced. For the piezoelectric shunt damping, a passive shunt circuit composed of inductors and a load resistor is connected to the piezoelectric patch mounted on the panel structure. An electrical impedance model is introduced for the system based on the measured electrical impedance, and the criteria for maximum energy dissipation at the shunt circuit is used to find the optimal shunt parameters. For multi-mode shunt damping, the shunt circuit is modified by the introduction of a block circuit. Also the optimal location of the piezoelectric patch is studied by finite element analysis in order to cause the maximum admittance from the patch for each mode of the structure. An acoustic test is performed for the panels and a remarkable noise reduction is obtained in multiple modes of the panel structure.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1574_1575
• /
• 2009

This paper investigates the reduction of RE(Radiated Emission) noise in a high power LED module circuit using PWM(Pulse Width Module) switching controller circuit. Poorly designed LED lighting module can experience the RE and CE(Conducted Emission) noise problem. This paper propose the reduction of noise source and improvement of EMI filter design in a high power LED lighting module. The experimental and simulation results showed that reduce the RE noise level effectively.

• 조명전기설비학회논문지
• /
• 제29권6호
• /
• pp.78-89
• /
• 2015

Conventional EMI filters have tried to use an active EMI filter as a series by the series connection of two EMI filters for CM and DM noise. However, the proposed filter is formed into one circuit by using the active EMI filter which is able to filter CM and DM noise components together. As a result, the active EMI filter showed the outstanding quality in mass and volume under 50% and electric characteristics have been compared to the passive EMI filter in approximately 150kHz~10MHz. Furthermore, the proposed circuit has simple circuit components by comparing with the series EMI filters, and electrical characteristics are similar. The noise have been attenuated to maximum 20dBuV.

• Journal of information and communication convergence engineering
• /
• 제15권4호
• /
• pp.237-243
• /
• 2017

This paper presents an analysis of the electromagnetic interference of a heterogeneous power bus where electromagnetic bandgap (EBG) cells are irregularly arranged. To mitigate electrical-noise coupling between high-speed circuits, the EBG structure is placed between parallel plate waveguide (PPW)-based power buses on which the noise source and victim circuits are mounted. We examine a noise suppression characteristic of the heterogeneous power bus in terms of scattering parameters. The characteristics of the dispersion and scattering parameters are compared in the sensitivity analysis of the EBG structure. Electric field distributions at significant frequencies are thoroughly examined using electromagnetic simulation based on a finite element method (FEM). The noise suppression characteristics of the heterogeneous power bus are demonstrated experimentally. The heterogeneous power bus achieves significant reduction of electrical-noise coupling compared to the homogeneous power buses that are adopted in conventional high-speed circuit design. In addition, the measurements show good agreement with the FEM simulation results.