• Journal of Power Electronics
• /
• v.18 no.4
• /
• pp.1268-1277
• /
• 2018

A relatively high operating frequency is required for efficient wireless power transfer (WPT). However, the alternating current (AC) resistance of coils increases sharply with operating frequency, which possibly degrades overall efficiency. Hence, the evaluation of coil AC resistance is critical in selecting operating frequency to achieve good efficiency. For a Litz wire coil, AC resistance is attributed to the magnetic field, which leads to the skin effect, the proximity effect, and the corresponding conductive resistance and inductive resistance in the coil. A numerical calculation method based on the Biot-Savart law is proposed to calculate magnetic field strength over strands in Litz wire planar spiral coils to evaluate their AC resistance. An optimized frequency can be found to achieve the maximum efficiency of a WPT system based on the predicted resistance. Sample coils are manufactured to verify the resistance analysis method. A prototype WPT system is set up to conduct the experiments. The experiments show that the proposed method can accurately predict the AC resistance of Litz wire planar spiral coils and the optimized operating frequency for maximum efficiency.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.5
• /
• pp.250-257
• /
• 2006

It is well known that Grain-oriented electrical steel sheets have two dimensional magnetic properties according to the direction of exciting field such as non-linear phase difference between magnetic flux density and magnetic field intensity vectors, different iron loss and permeability even when an alternating magnetic field is applied. The measurement and application of the two dimensional magnetic properties of the Grain-oriented electrical steel sheets, therefore, are very important for the design and precise performance analysis of electric machines made of them. As the direction of exciting field changes, in this paper, the two dimensional magnetic properties of a Grain-oriented electrical steel sheet, i.e., non-linear B-H curves, phase difference between B and H, and iron loss characteristics, are measured using SST(Single Sheet Tester) which has two axes excitation. The measured results are presented in two ways: using $(B,\theta_B)$ method and using hysteresis loops along rolling and transverse directions, respectively.

• Journal of the Korean Chemical Society
• /
• v.45 no.2
• /
• pp.156-161
• /
• 2001

Various oxidation states of Polyaniline(PANI) were chemically synthesized, and characterized by FT-IR, UV-Vis, GPC, TG-DTA, Single layer light emitting diodes(LED) were perpared by spin coating of LEB-PANI solutions which have various oxidation states onto an ITO substrate and subsequent vacuum deposition of aluminum top electrode and then current-voltage characteristics. EL spectrum was investigated It was found that ${\pi}$-${\pi}$* transition were shifled to longer wavelength and molecular excition transition were decreased in the UV-Vis spectra and the intensity of EL and PL were increased as the contents of fully reduced form LEB increased. The turn-on voltage of ITO/LEB/AI structured LED was 5 V. It was found that the white light was emitted only from the phase with reduced epeat unit.

• Journal of Power Electronics
• /
• v.17 no.4
• /
• pp.1109-1116
• /
• 2017

Wireless power transfer (WPT) technology has the advantages of intelligence and facilitation. This paper designs a WPT system applied to battery charging and provides a strategy which switches from the constant current (CC) charging mode to constant voltage (CV) charging mode. The LCL-LCL topology is used to realize the CC output, while the LCL-S (series compensation) topology is used to realize the CV output. The main factor affecting the output characteristics is extracted by analyzing the two topologies above. Based on the main factor, this paper puts forward a modified way to design the system. In addition, on-line monitors for the battery and switches are placed at receiving side, which avoids the need for introducing an information interaction module into the system. Therefore, the complexity of the controlling system is reduced. Finally, simulation and experimental analyses are carried out to verify the correctness of the compound topologies.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.849-853
• /
• 2009

A generator is in use for a moving vehicle like car, aircraft, ship as well as key industry including a thermal power plant, a water power plant, a nuclear power plant, and so on. Such the AC generator plays an important role in vehicle, ship, aircraft, and so forth, at the point of generating electric power. Especially in the matter of the ship, the emergency generator system is mounted to provide against malfunction of main generator on a voyage. So, it is ordered that the system can monitor the main generator and operate the emergency generator when the emergency happens. This study is about controller for the emergency diesel engine generator and design of a various software.

• Earthquakes and Structures
• /
• v.13 no.2
• /
• pp.211-220
• /
• 2017

Observations from past strong earthquakes revealed that near-fault ground motions could lead to the failure, or even collapse of electricity transmission towers which are vital components of an overhead electric power delivery system. For assessing the performance and robustness, a high-fidelity three-dimension finite element model of a long span transmission tower-line system is established with the consideration of geometric nonlinearity and material nonlinearity. In the numerical model, the Tian-Ma-Qu material model is utilized to capture the nonlinear behaviours of structural members, and the cumulative damage D is defined as an index to identify the failure of members. Consequently, incremental dynamic analyses (IDAs) are conducted to study the collapse fragility, damage positions, collapse margin ratio (CMR) and dynamic robustness of the transmission towers by using twenty near-fault ground motions selected from PEER. Based on the bending and shear deformation of structures, the collapse mechanism of electricity transmission towers subjected to Chi-Chi earthquake is investigated. This research can serve as a reference for the performance of large span transmission tower line system subjected to near-fault ground motions.

• Food Science of Animal Resources
• /
• v.28 no.5
• /
• pp.637-644
• /
• 2008

Four different extraction and purification methods were evaluated to determine the heterocyclic amines (HCAs) in fried pork patties. Pork patties were cooked in the teflon-coated electric frying pan at $230^{\circ}C$ for 8 min per side. HCAs in the fried pork patties were extracted and purified using four different solid-phase extraction (SPE) methods and quantitated by LC-MS (API-ESI). Recovery of four different extraction and purification methods was evaluated by comparing the HCAs amounts quantified by the standard addition method. Validation of extraction and purification methods for fried pork patties was determined to establish accurate sample preparation. The recoveries of HCAs from different SPE methods were calculated. The recovery yields were 15.7-68.7% (Polar amine group) and 25.0-74.7% (less-polar amine group) in method A. Method D provided recovery yields ranging from 14.1% to 68.7% in polar amine groups and from 3.0% to 72.3% in less-polar amine groups, respectively. Modified procedures of Method A and D were the most suitable extraction and purification method for HCAs analysis from fried pork patties.

• Journal of Ocean Engineering and Technology
• /
• v.32 no.4
• /
• pp.287-295
• /
• 2018

This paper presents the results of an exploration of the ferromanganese crusts of Western Pacific Seamount registered by the Korean government. This area has been surveyed with a deep-sea camera and crust samples have been acquired by deep-sea dredging since 2013. On October 18-19, 2017, a united research team from KIOST and KRISO explored two blocks, OSM11 and OSM07, on the seamount using Hemire ROV. A precise survey was conducted on the ferromanganese crusts and sediments covering the slope/top of OSM11 and the middle flat area of OSM07. Rock samples were collected with precise positioning, and HD videos were recorded for 7 hours. This paper discusses the technical issues of this exploration in terms of (1) how to deal with an emergency situation during an electric power blackout, (2) the improvement of the thruster power by adding cooling plugs to the housings of the thruster amplifiers, (3) the relative motion of the depressor by changing the fixing method of the cable terminator, which affects the service life of the cable, (4) a sampling technique for the steep slope of the seamount, (5) integrated navigation under a USBL blackout, and (6) a 3-dimensional image mosaic for visualizing the distribution state of the crusts.

• Polymer(Korea)
• /
• v.24 no.6
• /
• pp.860-868
• /
• 2000

In this work, the electro-magnetic interference (EMI) characteristics of PAN-based carbon fibers-reinforced composites are investigated with difference to manufactural parameters, i.e., fiber grade, fiber orientation angle, and laminating method. As a result, EMI shielding effectiveness (SE) of the composites greatly depends on a fiber orientation in composite angle. Especially, the fiber grade affects SE of composites in case of orientation angle of 0$^{\circ}$. Then the SE become greater as the change of electric character according to the arrangement directions, i.e., electrical anisotropy in the same constituent materials. This is due to the skin effect which is represented in the surface of electro-magnetic wave in high-frequency range. In all cases according to lamination methods, the composites represents SE of 83~98% over. Whereas, in symmetric and unsymmetric laminate structures, the SE decreases slightly as the laminate angles of composites increases. On the contrary. the repeating laminates structure shows the opposite tendency. Especially, 90$^{\circ}$ repeating laminate structure shows the SE more than 90% over the measuring frequency.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.2
• /
• pp.3430-3437
• /
• 1974

.It is very importaut to know the water consumption of crops in planning irrigation works and practicing suitable soil moisture management. For the purpose of making it clear that how much water be consumed to cultivate the Chinese cabbage, Chamber method has been applied. Main equipments in the transpiration chamber are flowers, manometer and electric thermograph. The chamber made of vynyl plate has a small entrance at the base and an exit at the top, and the ventilation in the chamber was carried out by a flower through the entrance and exit. Air-flow adjusted by an orifice manometer enters the chamber from the outside over the crop canopy through the pipe like a chimney and finally goes out to the outside. Two sets which consist of a pair of dry and wet bulb made by thermistor are installed in the entrance and exit tube, and record air temperature automatically. Evapotranspiration amount is computed from the air-flow quantity and difference in absolute humidity between at the entrance and exit of the chamber by the following equation: ET=(X2-X1)${\times}$Q where ET=evapotranspiration amount X1=absolute humidity at the entrance(g/㎥) X2=absolute humidity at the exit(g/㎥) Q=air-flow quantity(㎥) This study was carried out at the upland farm of the Institute of Agriculture Engimeering and Utilization, Suwon, Korea. from 1971 to 1973. The results obtained in this experiment are as follows: 1. The total amount of evapotranspiration of Chinese Cabbage that is cultivated in autumn is 408.1mm during growth period. 2. Chinese cabbage rapidly grows up in the second ten days of September, 40th to 50th days after seeding. At the same time, the maximum amount of evaportranspiration of Chinese cabbage is 61.6mm/10 days 3. The correlation between Pan-evaporation and evapotranspiration is high, coefficient of correlation r=0.88**, and can be shown as The following regression equation: ET=0.913E+20.273 4. Evapotranspiration is closely related with meteorological factors: r=0.85**, for insolation, r=0.76** for air temperature, respectively. 5. The percentage of evapotranspiration amount, at the beginning of growth stage, gradually increases in proportion as the Chinese Cabbage grows but is largely affected by meteorological factors after the green cover formation. 6. By Blaney and Griddle formula, evaportranspiration coefficient "K" are within from 0,85 to 1.27.