• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.1
• /
• pp.53-61
• /
• 2010

In the present study, a laminar natural convection flow of $H_2O$-Cu nanofluid in a two dimensional enclosure has been investigated using a thermal lattice Boltzmann approach with the Bhatnagar-Gross-Krook (BGK) model. The effect of suspended nanoparticles on the fluid flow and heat transfer process have been studied for different controlling parameters such as particle volume fraction ($\Phi$), Rayleigh number (Ra). For this investigation the Rayleigh number changes from 104 to 106 and volume fraction varied from 0 to 10% with three different particle diameters (dp), say 10 nm, 20 nm and 40 nm. It is shown that increasing the Rayleigh number (Ra) and the volume fraction of nanofluid causes an increase of the effective heat transfer rate in terms of average Nusselt number (Nu) as well as the thermal conductivity of nanofluid. On the other hand, increasing the particle diameter causes the decrease of the heat transfer rate and thermal conductivity. The result of the analysis are compared with experimental and numerical data both for pure and nanofluids and it is seen a relatively good agreement.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.2
• /
• pp.259-267
• /
• 1997

The advent of B-ISDN using ATM(asynchronous transfer mode) made possible a variety of new multimedia services, however it also created a problem of congestion control due to bursty nature of various traffic sources. To tackle this problem, UPC/NPC(user parameter control/network parameter control) have been actively studied and DRLB(dynamic rate leaky bucket) algorithm, in which the token generation rate is changed according to states of data source andbuffer occupancy, is a good example of the UPC/NPC. However, the DRLB algorithm has drawbacks of low efficiency and difficult real-time implementation for bursty traffic sources because the determination of token generation rate in the algorithm is based on the present state of network. In this paper, we propose a more plastic and effective congestion control algorithm by combining the DRLB algorithm and neural network based prediction to remedy the drawbacks of the DRLB algorithm, and verify the efficacy of the proposed method by computer simulations.

• Quality Improvement in Health Care
• /
• v.9 no.2
• /
• pp.116-133
• /
• 2002

Background : It is very common in Korea to take care of non-acute patients in an acute setting, due to the lack of long-term facilities. Long term hospitalization increase medical expenses and decreases the bed utilization, which can affect the urgent and emergent admissions, and eventually jeopardize the hospital financially. In this study, strategies for effective transfers to the lower levels of care, and to decrease the length of stay were presented by surveying and analyzing the patient's knowledge of the transfer needs, and the willingness to transfer those whose hospital length of stay was more than 30days. Method : The survey is subject to a group of 251 patients who have been hospitalized over 30 days in a general hospital in Seoul. Excluding those that were in the Intensive Care Unit and psychiatric ward, 214 in-patients were used as participants. They were surveyed from April 9, 2002 to April 17, 2002. One hundred and thirty seven out of 214 were responded which made the response rate 64%. Data were analyzed by SAS and SPSS. Result : Multi-variable Logistic Regression Analysis showed a significant effect in medical expenses, knowledge of referral system and the information of the receiving hospital. The financial burden in medical expenses made the patient 10.7 times more willing to be transferred, knowledge of the referral system made them 5 times more willing to be transferred, and the information of receiving hospital makes 6.5 times more willing to be transferred. Reasons for willing to be transferred to a lower level of care were the phase of physical therapy, the distance from home, the attending physician's advice and being unable to be treated as an out patient. Reasons for refusing to be transferred were the following. The attending physician's competency, not being ready to be discharged, not trusting the receiving hospital's competency due to the lack of information, or never hearing about the referring system by the attending physician. Conclusion : Based on this, strategies for the effective transfer to the lower levels of care were suggested. It is desirable for the attending physician to be actively involved by making an effort to explain the transfer need, and referring to the Healthcare Coordinating Center, which can help the patient make the right decision. Nationwide networking for the referral system is the another key factor that may need to be suggested as an alternative to decrease the medical expenses. Collaborating with the Home Health Agency for the early discharge planning and the Social Service Department for financial aid are also needed. It is recommended that the hospital should expedite the transfer process by prioritizing the cost and the information as medical expenses, knowledge of referring system and the information of the receiving hospital, are the most important factors to the willingness to transfer to a lower level of care.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.4
• /
• pp.344-355
• /
• 2017

In this study, a numerical approach is adopted to investigate the effectiveness factors for distributed electrochemical reactions in thin active reaction layers of solid oxide fuel cells (SOFCs), taking into account the Butler-Volmer reaction kinetics. The mathematical equations for the electrochemical reaction and charge conduction process were formulated by assuming that the active reaction layer has a small thickness, homogeneous microstructure, and high effective electronic conductivity. The effectiveness factor is defined as the ratio of the actual reaction rate (or equivalently, current generation rate) in the active reaction layer to the nominal reaction rate. From extensive numerical calculations, the effectiveness factors were obtained for various charge transfer coefficients of 0.3-0.8. These effectiveness data were then fitted to simple correlation equations, and the resulting correlation coefficients are presented along with estimated magnitude of error.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.3
• /
• pp.117-124
• /
• 2005

Electrochemical oxidation of ethanol at nickel electrodes has been studied in 1 M KOH solution containing 0.20M ethanol using electrochemical impedance spectroscopy. Equivalent circuits have been worked out by simulating the impedance data, and the results were used to model the oxidation of ethanol as well as the passivation of the electrode. The maximum rate of oxidation of $Ni(OH)_2$ to NiOOH was observed at about 0.37V vs. Ag/AgCl reference electrode, while the maximum rate of ethanol oxidation at the Ni electrode was observed at about 0.42V, The charge-transfer resistance for oxidation of the electrode itself became smaller in the presence of ethanol than in its absence. These results suggest that the $\beta-Ni(OH)_2/\beta-NiOOH$ redox couple is acting as an effective electron transfer mediator far ethanol oxidation. The kinetic parameters also were obtained by the experimental and simulated results.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.3
• /
• pp.18-25
• /
• 2002

Research to discuss the fire performance of materials requires tools for measuring their burning characteristics and validated fire growth models to predict fire behavior of the materials under specific tire scenarios using the measured properties as input for the models. In this study, burning characteristics such as time to ignition, weight loss rate, flame spread, heat release rate, total heat evolved, and effective heat of combustion for four types of wood-based materials were evaluated using the cone calorimeter and inclined panel tests. Time to ignition was affected by not only surface condition and specific gravity of the tested materials but also the type and magnitude of heat source. Results of weight loss rate, measured by inclined panel tests, indicated that heat transfer from the contacted flame used as the heat source into the inner part of the specimen was inversely proportional to specific gravity of material. Flame spread was closely related with ignition time at the near part of burning zone. Under constant and severe external heat flux, there was little difference in weight loss rate and total heat evolved between four types of wood-based panels. More applied heat flux caused by longer ignition time induced a higher first peak value of heat release rate. Burning characteristics data measured in this study can be used effectively as input for fire growth models to predict the fire behavior of materials under specific fire scenarios.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.8
• /
• pp.1217-1226
• /
• 1989

This paper describes a design of hardware system for real time automatic diagnosis of ECG arrhythmia based on pipeline processor consisting of three microcomputer. ECG data is acquisited by 12 bit A/D converter with hardware QRS triggered detector. Four diagnostic parameters-heart rate, morpholigy, axis, and ST segment-are used for the classification and the diagnosis of arrhythmia. The functions of the main CPU were distributed and processed with three microcomputers. Therefore the effective data process and the real time process using microcomputer can be obtained. The interconnection structure consisting of two common memory unit is designed to decrease the delay time caused by data transfer between processors and be which the delay time can be taken 1% of one clock period.

• Journal of Biomedical Engineering Research
• /
• v.9 no.1
• /
• pp.79-86
• /
• 1988

This paper describes the design of a hardware systenl for ECG feature extraction based on pipeline processor consistinsf of three microcomputers. ECG data is acquisited by 12 bit A/D converter with hardware QRS triggered detector. Four diagnostic parameters parameters-heart rate, morPhology, axis, and 57 segment-are used for the classification and the diagnosis of arrhythmia. The functions of the main CPU were distributed and processed with three microcomputers. Therefore the effective data process and the real time process using microcomputer can be obtained. The interconnection structure consisting of two common memory units is designed to decrease the delay time caused by data transfer between processors and designed by which the delay time can be taken Loye of one clock period.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.731-733
• /
• 1988

This paper describes a design of hardware system for real time automatic diagnosis of ECG arrhythmia based on pipeline processor consisting of the three microcomputer. ECG data is acquisited by 12 bit A/D converter with hardware QRS triggered detector. Four diagnostic parameters - heart rate, morphology, axis, and ST segment - are used for the classification and the diagnosis of arrhythmia. The functions of the main CPU were distributed and processed with three microcomputers. There-fore the effective data process and the real time process using microcomputer can be obtained. The interconnection structure consisting of two common memory units is designed to decrease the delay time caused by data transfer between processors and by which the delay time can be taken 1 % of one clock period.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.337-340
• /
• 2005

Rotating annular disks are widely used in data storage devices such as CDs, DVDs(digital versatile disks), and HDs(hard disks). Higher data transfer rate in data storage disks could not be achieved by polycarbonate disks in the present market. The problem can be solved by applying the fiber-reinforce composite materials to the disks. In this paper, an application of composite materials to rotating disks is proposed to increase the critical speed. Dynamic equation is formulated in order to calculate the natural frequency and critical speed for rotating composite by the Galerkin method. The results show that the radially reinforced disk is more effective in increasing critical speed than the circumferentially reinforced disk.