• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2001.04a
• /
• pp.14-14
• /
• 2001

WC-Co 계의 입성장 억제는 현재 초경합금 분야에서 공학적으로 가장 중요한 이슈들 중의 하나이다 VC를 비롯한 입방정 탄화물이나 $Cr_3C_2$ 등의 여러 가지 탄화 물이 혼합되어 입성장 억제에 이용되는데 입성장 억제의 효과는 대략적으로 용해되는 탄화물의 양에 의존하고 있는 것으로 추정된다. 보다 효율적으로 입성장 억제를 실현하려면 입성장 기구를 명확히 할 필요가 있다. 최 등[1]은 VC가 WC 입자 표면 에서의 edge energy를 증가시켜서 2차원 핵생성의 에너지 장벽을 올리게 하고 이에 따라 입성장이 억제된다는 모델을 제안하였다. 이러한 모텔을 입증하기 위해서는 이론적으로만 예측이 가능한 edge energy보다 좀 더 명확한 물리적인 변수가 제시되어야 할 것이다. 여기서는 또 다른 계인 NbC- TiC-Co 계에서 NbC와 TiC의 버에 따른 입성장 거동과 입자의 형상간의 관계로부터 업성장과 edge energy 그리 고 edge energy와 입자 형상간의 관계를 알아보고 이로부터 좀 더 구체적인 의미 에서의 입성장 모텔과 입성장 억제기구를 제시하고자 한다.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.99-102
• /
• 2000

We have studied the effects of d-wave symmetry on the critical current of YBa$_2$Cu$_3$O$_7$ step-edge Josephson junctions. The critical current along various misorientation angle was measured and analyzed with the concept of grain-boundary junctions with d-wave symmetry. Experimental results of c-oriented YBCO step-edge junctions with various in-plane misorientation angles were qualitatively in good agreement with the theory. The out-of-plane misorientation angle is usually formed between two grains with the c axes perpendicular to each other and is normally not controllable.

• Journal of the Korea Furniture Society
• /
• v.11 no.1
• /
• pp.61-68
• /
• 2000

This study was carried out to investigate the effect of grain and veneer thickness on drying rate, required energy consumption, and drying defects such as checking, end waving, and burning during a far-infrared radiation drying process of decorative veneers of hard maple and beech. Most of the veneer could be dried from green to in-use moisture content within 30 to 360 seconds. The drying rates were significantly affected by veneer thickness, but there was little difference between edge-and flat-sliced veneers. The formation of checking during drying test was none or very slight. The percentages of the veneers defected by checks were higher in the flat-sliced veneers than in the edge-sliced veneers. The maximum end wavinesses in the flat-sliced veneers were almost 1.6 to 3 times larger than that in the edge-sliced veneers. All veneers were fee from burned marks during drying test.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.3
• /
• pp.431-438
• /
• 1996

Transmission electron microscopy has been used to investigate the microstructure of hot-pressed $TiB_{2}$. Thin foil specimens, prepared by conventional ion beam thinning, revealed many features which originated from the crystallographic anisotropy of hexagonal $TiB_{2}$. It was observed that in these specimens Fe-impurities are precipitated to form secondary Fe-rich phases at grain triple edges, in grain boundaries and sometimes in-grain. These Fe-rich precipitates were characterised by their coherence or semi-coherence to a favourably oriented grain at a grain triple edge or grain boundaries or to the matrix $TiB_{2}$ phase.

• Transactions of Materials Processing
• /
• v.28 no.5
• /
• pp.257-265
• /
• 2019

Multi-axial forging (MAF), a severe plastic deformation technique, is known to be difficult to obtain materials with homogeneous microstructures. Recently, multi-axial diagonal forging (MADF) process has been developed to solve this problem. In this study, in order to compare the microstructural and mechanical homogeneities of the MAFed and MADFed samples, oxygen-free copper (OFC) cubes measuring 25 mm in length were deformed through MAF and MADF processes and the average grain size and hardness were measured at the edge, face, and center regions of the samples. In the MAFed samples, ultrafine grains were formed at the center region, but a considerable amount of coarse grains remain at the face region. Therefore, the MAFed samples showed a high inhomogeneity in regards to grain size and hardness. On the contrary, in the case of the MADFed sample, the grain sizes at the edge, face, and center regions were similar and the hardness in all the regions are almost similar. This indicates that the MADFed sample has a homogeneous microstructure and uniform mechanical properties, which can be attributed to the homogeneous distribution of the effective strain throughout the material. The results of this study suggests that the MADF is a suitable process in the fabrication of high-strength copper materials with a homogeneous and ultrafine grain structure.

• Journal of the Korea Furniture Society
• /
• v.25 no.1
• /
• pp.36-44
• /
• 2014

This study was investigated to sensible characteristic and physical characteristic to estimate value of the craft for Pinus densiflora and Pinus densiflora for. erecta Uyeki wood. The sensual characteristics of wood are evaluated by wood figure, wood grain, odor, and the physical characteristics by weathering, abrasion, surface roughness and hardness. The wood figure of these species were observed at flat grain in the radial section and edge grain in the tangential section. Also, burl's figure was observed in Burl of Pinus densiflora wood. Pinus densiflora for. erecta Uyeki wood had volatile aroma compounds such as Camphene, Thymyl ether, ${\alpha}$-Longipinene, etc. Pinus densiflora wood had volatile aroma compounds such as ${\alpha}$-Longipinene, (+)-Cedrol, etc. The moisture soption, abrasion, hardness and roughness were very different between the two species.

• Korean Journal of Materials Research
• /
• v.16 no.6
• /
• pp.360-366
• /
• 2006

A series of ZnO thin films were grown by radio-frequency (RF) magnetron sputtering with various RF powers on $SiO_2/Si$(100) substrates at $500^{\circ}C$. Thicknesses of the investigated ZnO films were fixed to about 250nm by changing the growth time based on the changes of growth rates with RF powers. All the ZnO thin films were grown with <0001> preferred orientation. Average grain sizes of about 250nm-thick ZnO films evaluated by FE-SEM, AFM, and TEM were increased by decreasing the RF power. Structural properties addressed by FWHM values of XRD (0002) omega rocking curves and their intensities were better for the smaller grain sized ZnO films grown with high RF powers, which implies small values of tilt for smaller grain sized ZnO films. However, optical properties addressed by intensities of band edge emissions from room temperature and low temperature photoluminescence were better for the larger grain sized ZnO films with low RF power, which implies grain boundaries acted as nonradiation recombination centers.

• Journal of Korea Water Resources Association
• /
• v.52 no.7
• /
• pp.493-503
• /
• 2019

This study presents a new method of estimating the size distribution of river bed gravel through image processing. The analysis was done in two steps; first the individual grain images were analyzed and then the grain particle segmentation of river-bed images were processed. In the first part of the analysis, the relationships (long axes, intermediate axes and projective areas) between grain features from images and those measured were compared. For this analysis, 240 gravel particles were collected at three river stations. All particles were measured with vernier calipers and weighed with scales. The measured data showed that river gravel had shape factors of 0.514~0.585. It was found that the weight of gravel had a stronger correlation with the projective areas than the long or intermediate axes. Using these results, we were able to establish an area-weight formula. In the second step, we calculated the projective areas of the river-bed gravels by detecting their edge lines using the ImageJ program. The projective areas of the gravels were converted to the grain-size distribution using the formula previously established. The proposed method was applied to 3 small- and medium- sized rivers in Korea. Comparisons of the analyzed size distributions with those measured showed that the proposed method could estimate the median diameter within a fair error range. However, the estimated distributions showed a slight deviation from the observed value, which is something that needs improvement in the future.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.4
• /
• pp.62-67
• /
• 2000

The dressing time monitoring in cylindrical grinding is very important with respect to machining efficiency. Therefore, the purpose of this paper is to determine the wheel life by monitoring behavior of grinding power for WA, 19A and GC. For this purpose , we investigated indirectly the attritious wear of grain edge, the loading of grinding wheel and the breakage of grain through the grinding power and the surface roughness under various grinding conditions. From obtained the results, the relationship between the wheel life and the average sectional chip area is examined to guide for the determination of dressing time.

• Journal of the Korean Ceramic Society
• /
• v.42 no.9 s.280
• /
• pp.599-601
• /
• 2005

The coarsening process of two different $BaTiO_3$ single crystal seeds, one with a (111) double twin and the other without it, was investigated. Due to the presence of Twin Plane Reentrant Edge (TPRE), the coarsening rate of the twinned seed crystal was significantly higher than that without a twin. For the coarsening by the 2-dimensional nucleation and lateral growth, the energy barrier for nucleation at the TPRE was analyzed to be about a half compared with that at the terrace planes.