• 한국산학기술학회논문지
• /
• 제14권1호
• /
• pp.57-62
• /
• 2013

카트 차체에는 현가장치와 차동장치가 존재하지 않으므로 카트주행 중 발생하는 프레임의 변형은 탄성변형으로 인한 주행성능과 프레임의 피로수명에 영향을 미친다. 선회주행 시 비틀림 변형에 의한 카트의 거동은 이 두 가지 변형에 결정적 원인을 제공한다. 이러한 곡선구간에서 카트의 동적 거동을 분석하기 위하여 GPS를 이용하여 차량의 궤적을 추적하고 카트 프레임 강에 작용하는 비틀림 응력을 측정하였다. 레저와 레이싱 카트 프레임의 기계적 성질을 파악하기 위해 재질 분석과 인장시험을 실시하여 각 프레임의 재료 특성을 분석하였다. 비틀림 응력집중과 프레임 비틀림은 프레임 해석을 통해 조사되었다. 또한 주행 분석 장치를 이용하여 레저와 레이싱 카트를 각 조건별로 실차실험을 수행하였고, 이를 통해 곡선구간에서 카트의 주행거동을 분석하였다. 선회주행 시 차량에 원심력에 의한 하중이동의 현상이 발생했으며, 이로 인해 카트 프레임 강에 비틀림 응력이 발생하였다.

• 한국지반공학회논문집
• /
• 제16권1호
• /
• pp.157-165
• /
• 2000

본 연구에서는 선철의 제조과정에서 부산물로 발생되는 수경성 입도조정 고로 슬래그(이하HMS-25라 함)의 철도 노반재로서의 적용성 및 성능평가 검토를 하였다. 실험은 기본물성 측정을 위한실내시험, 일축압축강도시험 및 정ㆍ동적 특성분석을 위한 모형토조실험 및 공진주/비틂 전단시험을 실시하였다. HMS-25의 일축압축강도시험 결과, 수경성에 의한 강도 증진 효과를 확인하였다. 토조시헌에서는 HMS-25를 이용하여 조성한 노반이 흙노반에 비해 지지력 및 침하량측면에서 효과적인 것으로 나타났다. 공진주/비틂전단시험에서는 전단탄성계수는 구속압의 0.5 제곱으로 증가하였으며, 재령에 따라 증가하는 경향을 보였다.

• 대한금속재료학회지
• /
• 제46권9호
• /
• pp.563-571
• /
• 2008

The influence of annealing treatment on dynamic deformation behavior of ultra-fine grained aluminum alloys was investigated in this study. After equal-channel angular pressing at $200^{\circ}C$, most of the grains were considerably reduced to nearly equiaxed grains of $0.3{\mu}m$ in size. With an increment of various annealing treatments for 1 hour, resultant microstructures were found to be fairly stable at temperatures up to $200^{\circ}C$, suggesting that static recovery would be dominantly operative, whereas grain growth was pronounced above $250^{\circ}C$. The tensile test results showed that yield and ultimate tensile strengths decreased, but elongation-to-failure and strain hardening rate increased with increasing annealing temperature. The dynamic deformation behavior retrieved with a series of torsional tests was explored with respect to annealed microstructures. Such mechanical response was analyzed in relation to resultant microstructure and fracture mode.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.306-309
• /
• 2009

The influence of equal-channel angular pressing (ECAP) route on dynamic deformation behavior of ultra-fine grained Al-4.4%Mg alloys was investigated in this study. The 8-pass ECAPed specimens consisted of ultra-fine grains of $0.5{\mu}m$ in size, and contained the considerable amount of second phase particles, which were fragmented and distributed homogeneously in the matrix. The result of dynamic torsional tests indicated that the maximum shear stress and fracture shear strain were lowest in the specimen deformed by ECAP via route A among the 8-pass ECAPed specimens. The formation of adiabatic shear bands was addressed by concepts of critical shear strain, deformation energy required for void initiation, and microstructural homogeneity related to ECAP routes.

• 대한기계학회논문집A
• /
• 제41권6호
• /
• pp.567-573
• /
• 2017

자동차 부품 중 드라이브 샤프트는 엔진에서 발생하는 토크를 바퀴에 전달하는 동력 전달장치의 핵심 부품이다. 엔진에서 입력되는 비틀림 하중과 주행 중 발생하는 실동하중에 의한 부품의 파손을 방지하기 위해, 고주파 열처리로 강도 및 피로수명이 개선되고 있다. 본 연구에서는 고주파 열처리에 따른 드라이브 샤프트의 피로수명을 정량적으로 평가할 수 있는 피로수명 평가기법을 구축하였다. 드라이브 샤프트의 소재인 SAE10B38M2 강재로 모재 및 경화깊이가 서로 다른 고주파 열처리 시편 두 종을 제작하여 비틀림 하중 하에서의 전단 변형률 제어 피로시험을 진행하였고, 변형률-수명 피로수명 평가에 필요한 피로 물성값을 구하였다. 얻어진 피로 물성값을 이용하여 드라이브 샤프트의 변형률 기반 피로해석을 진행하였으며, 얻어진 피로수명 결과를 시제품 피로시험 결과와 비교하여 해석기법의 타당성을 검증하였다.

• 한국지반공학회지:지반
• /
• 제11권1호
• /
• pp.101-112
• /
• 1995

동적하중을 받는 지반-구조물 시스템의 설계를 위해 전단탄성계수와 감쇠비로 표현되는 지반의 변형특성의 결정은 매우 중요하다. 본 논문에서는 공진주/비틂전단시험기를 이용하여 저변형률 및 중간 변형률하에서 건조사질토의 변형특성을 연구하였다. 동적시험인 공진주시험과 반복시험인 비틀전단시험을 동일한 공시 체를 이용하여 실시하였다. 진동측정시스템을 개량하여 응력 -변형관계가 하중반복회수와 전단변형률의 크기에 영향을 받지않는 선형영역을 찾았으며 이 영역에서 이력감쇠가 존재함을 나타내었다. 반복한계변형률 이상에서는 하중반복회수에 따라 전단탄성계수는 증가하고 감쇠비는 감소하였다. 사질토의 전단탄성계수와 감쇠비는 진동주파수에 영향을 받지 않으며 의사정적시험인 비틈전단시험에서 변형특성과 동적시험인 공진주 시험에서 얻은 값은 비교시 하중반복회수의 영향을 고려하면 동일하다. 그러므로 공진주l비틀전단시 험을 통해 얻은 변형특성은 지반-구조물시스템의 동적해석은 물론 정적해석에서도 적용할 수 있다.

• Restorative Dentistry and Endodontics
• /
• 제42권3호
• /
• pp.216-223
• /
• 2017

Objectives: The aim of this study was to compare the mechanical properties of various nickel-titanium (NiTi) files with similar tapers and cross-sectional areas depending on whether they were surface-treated. Materials and Methods: Three NiTi file systems with a similar convex triangular cross-section and the same ISO #25 tip size were selected for this study: G6 (G6), ProTaper Universal (PTU), and Dia-PT (DPT). To test torsional resistance, 5 mm of the straightened file's tip was fixed between polycarbonate blocks (n = 15/group) and continuous clockwise rotation until fracture was conducted using a customized device. To evaluate cyclic fatigue resistance, files were rotated in an artificial curved canal until fracture in a dynamic mode (n = 15/group). The torsional data were analyzed using 1-way analysis of variance and the Tukey post-hoc comparison test, while the cyclic fatigue data were analyzed using the Mann-Whitney U test at a significance level of 95%. Results: PTU showed significantly greater toughness, followed by DPT and G6 (p < 0.05). G6 showed the lowest resistance in ultimate torsional strength, while it showed a higher fracture angle than the other files (p < 0.05). In the cyclic fatigue test, DPT showed a significantly higher number of cycles to failure than PTU or G6 (p < 0.05). Conclusions: Within the limitations of this study, it can be concluded that the torsional resistance of NiTi files was affected by the cross-sectional area, while the cyclic fatigue resistance of NiTi files was influenced by the surface treatment.

• 한국자동차공학회논문집
• /
• 제20권5호
• /
• pp.65-70
• /
• 2012

Torque fluctuation of engine generate gear rattle noise of transmission and many researches have been studied to decrease rattle noise by adjusting clutch damper system. So design optimization of clutch system is very important to decrease rattle noise and need knowing clutch dynamic torque at real vehicle driving condition. This makes it possible to measure clutch dynamic torque by using a small-size magnetic sensor. We install a small-size magnetic sensor on the input shaft of the transmission and measure the relative angular displacement between clutch hub and disc plate. We can obtain the clutch torque correspond to the angular displacement in the clutch torsional characteristics test. The object of this research is to measure clutch dynamic torque on real vehicle condition. Therefore, Clutch dynamic torque is very useful for investigating operating range of clutch according to engine torque and predicting the damping performance of torsional vibration on the powertrain.

• Wind and Structures
• /
• 제12권5호
• /
• pp.413-424
• /
• 2009

A series of wind tunnel free-decay sectional model dynamic tests were conducted to examine the effects of torsional-to-vertical natural frequency ratio of 2DOF bridge dynamic systems on the aerodynamic and dynamic properties of bridge decks. The natural frequency ratios tested were around 2.2:1 and 1.2:1 respectively, with the fundamental vertical natural frequency of the system held constant for all the tests. Three 2.9 m long twin-deck bridge sectional models, with a zero, 16% (intermediate gap) and 35% (large gap) gap-to-width ratio, respectively, were tested to determine whether the effects of frequency ratio are dependent on bridge deck cross-section shapes. The results of wind tunnel tests suggest that for the model with a zero gap-width, a model to approximate a thin flat plate, the flutter derivatives, and consequently the aerodynamic forces, are relatively independent of the torsional-to-vertical frequency ratio for a relatively large range of reduced wind velocities, while for the models with an intermediate gap-width (around 16%) and a large gap-width (around 35%), some of the flutter derivatives, and therefore the aerodynamic forces, are evidently dependent on the frequency ratio for most of the tested reduced velocities. A comparison of the modal damping ratios also suggests that the torsional damping ratio is much more sensitive to the frequency ratio, especially for the two models with nonzero gap (16% and 35% gap-width). The test results clearly show that the effects of the frequency ratio on the flutter derivatives and the aerodynamic forces were dependent on the aerodynamic cross-section shape of the bridge deck.

• Journal of Advanced Research in Ocean Engineering
• /
• 제4권4호
• /
• pp.174-184
• /
• 2018

We herein propose a new design procedure of a flexible container ship model where the vertical bending and torsional vibration modes are similar to its prototype. To achieve similarity in torsional vibration mode shapes, the height of the shear center of the model must be located below the bottom hull, similar to an actual container ship with large opening decks. Therefore, we designed a ship model by imparting appropriate stiffness to the hull, using urethane foam without a backbone. We built a container ship model according to this design strategy and validated its dynamic elastic properties using a decay test. We measured wave-induced structural vibrations and present the results of tank experiments in regular and freak waves.